Source: https://mokxi.com/teachers/plans/audio-amplifiers
Updated: 2026-11-19

Lesson plan

# Audio electronics lesson plan

Advanced, after the Op-amp circuit cookbook: preamps, tone controls, amplifier classes, distortion, speakers and impedance, hum and noise, and a class A guitar amp channel you voice yourself.

7 chapters, 7 lessons, about 6 hours, no board. Every lesson runs in the browser, with nothing to install.

Start a class from this course

The unit

## Objectives and materials

### By the end, students can

- Gain, input impedance, headroom and a log volume pot.
- A treble cut and a bass cut, each one RC corner.
- Where the watts go in class AB and class A.
- Soft clipping, hard clipping and asymmetry.
- Watts into ohms, cables and damping factor.
- Ground loops, balanced inputs and grounding rules.
- A class A guitar amp channel, voiced by you.

### Materials for the whole unit

- Capacitor x 2
- Diode x 2
- Function generator x 2
- Multimeter x 5
- Oscilloscope
- Potentiometer
- Resistor x 11
- Signal generator
- Slide switch
- Speaker, 8 ohm x 2
- TL072 dual JFET op-amp
- Transistor (NPN or PNP) x 3

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 55 min

## Preamps

Gain, input impedance, headroom and a log volume pot.

Lesson | Time | What students do

Preamps A guitar into a TL072 preamp: gain in decibels, the input impedance a pickup needs, the headroom a hot pickup eats, and why a volume knob is a log pot. | 55 min

- Run it: a gain of 11
- Gain in decibels
- Input impedance
- Headroom
- The volume knob
- Why the taper is log

### Materials

- Function generator
- Multimeter x 3
- Oscilloscope
- Potentiometer
- Resistor x 5
- TL072 dual JFET op-amp

### Check for understanding

Each student finishes "Preamps" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Why the taper is log".

Chapter 2. About 45 min

## Tone controls

A treble cut and a bass cut, each one RC corner.

Lesson | Time | What students do

Tone controls A guitar's own treble-cut knob and a bass-cut coupling capacitor, each buffered by half a TL072: a 723 Hz corner that darkens the highs and leaves the lows alone, and a 159 Hz corner that thins the bass. | 45 min

- Run it: knob on 10
- Knob on 0
- The lows walk through
- Bass cut
- Predict: a fatter capacitor

### Materials

- Capacitor x 2
- Function generator
- Multimeter x 3
- Resistor x 3
- TL072 dual JFET op-amp

### Check for understanding

Each student finishes "Tone controls" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Predict: a fatter capacitor".

Chapter 3. About 45 min

## Amplifier classes

Where the watts go in class AB and class A.

Lesson | Time | What students do

Amplifier classes Where a power amp's watts go: a class AB push-pull stage that idles at 190 mA and reaches 31 percent at full drive, and a class A stage that burns 22 W to deliver 2. The efficiency arithmetic behind class D. | 45 min

- Run it: class AB
- What the supply gives
- Turn it up
- Class A idles hot
- Class A at full drive

### Materials

- Diode x 2
- Function generator x 2
- Multimeter x 5
- Oscilloscope
- Resistor x 5
- Speaker, 8 ohm x 2
- Transistor (NPN or PNP) x 3

### Check for understanding

Each student finishes "Amplifier classes" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Class A at full drive".

Chapter 4. About 55 min

## Distortion

Soft clipping, hard clipping and asymmetry.

Lesson | Time | What students do

Distortion A TL072 gain stage into back-to-back diodes: a clipper that leaves a small signal alone and squashes a big one, a drive knob that changes the sound more than the level, asymmetric clipping that adds DC, and the hard clip of the rails. | 55 min

- Run it: gain before the clipper
- The diodes squash it
- Drive down: clean
- Drive up: compression
- Asymmetric clipping
- Hard clipping at the rails

### Materials

- Diode x 2
- Function generator
- Multimeter x 3
- Oscilloscope
- Resistor x 5
- TL072 dual JFET op-amp

### Check for understanding

Each student finishes "Distortion" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Hard clipping at the rails".

Chapter 5. About 55 min

## Speakers and impedance

Watts into ohms, cables and damping factor.

Lesson | Time | What students do

Speakers and impedance An amp into an 8 ohm speaker: P = V squared over R, a 4 ohm load that doubles the watts, a thin cable that steals them, a tube amp's output impedance and damping factor, and why half the volts is a quarter of the power. | 55 min

- Run it: 2 W into 8 ohms
- A 4 ohm speaker
- The cable steals watts
- A tube amp's output
- Two cabinets
- Predict: half the volts

### Materials

- Multimeter x 2
- Resistor x 3
- Signal generator
- Slide switch
- Speaker, 8 ohm x 2

### Check for understanding

Each student finishes "Speakers and impedance" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Predict: half the volts".

Chapter 6. About 55 min

## Hum and noise

Ground loops, balanced inputs and grounding rules.

Lesson | Time | What students do

Hum and noise A ground loop puts 60 Hz under the guitar: a single-ended input amplifies it, a balanced input throws it away, a high pass only half helps, and a 120 Hz buzz gets through more. The grounding rules that prevent it. | 55 min

- Run it: guitar plus hum
- Mute the guitar
- A balanced input
- Filter it out?
- The buzz is worse
- Grounding rules

### Materials

- Capacitor
- Function generator
- Multimeter x 3
- Resistor x 7
- Signal generator
- TL072 dual JFET op-amp

### Check for understanding

Each student finishes "Hum and noise" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Grounding rules".

Chapter 7. About 45 min

## Boss build

A class A guitar amp channel, voiced by you.

Lesson | Time | What students do

Boss build: a class A guitar amp channel A whole channel: a TL072 preamp with a gain knob, diode overdrive, a tone knob, a power stage and a class A TIP41C into an 8 ohm load. Set it clean, then dirty, read what the output stage burns, and voice it yourself. | 45 min

- Run it: clean
- Turn the gain up
- What class A costs
- Make it yours: voice the clean channel
- Your amp sheet

### Materials

- Capacitor x 2
- Diode x 2
- Function generator
- Multimeter x 3
- Oscilloscope
- Resistor x 11
- TL072 dual JFET op-amp
- Transistor (NPN or PNP)

### Check for understanding

Each student finishes "Boss build: a class A guitar amp channel" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Your amp sheet".

Your class

## Teach this unit as a class

Start a class from this course and its 7 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.

Start a class from this course See the demo class

More units

## Other lesson plans

Electronics basics 20 lessons, about 10 h. Embedded on the Arduino Uno 16 lessons, about 12 h. Embedded on the ESP32-C3 13 lessons, about 11 h. Embedded on the Raspberry Pi Pico 7 lessons, about 6 h. Build your own fight stick 5 lessons, about 4 h. Embedded on the STM32F411 6 lessons, about 6 h. C++ on a board 13 lessons, about 10 h. Digital logic and memory 4 lessons, about 4 h. Interactive devices on the Uno 9 lessons, about 8 h. From gates to a computer 23 lessons, about 16 h. Build a claw machine 8 lessons, about 6 h. Every unit All the courses as ready-made units, on the teachers page.
