Source: https://mokxi.com/solar-panel-simulator Simulator # A solar panel simulator: find the 1 W point Mokxi is a free online solar panel simulator that runs in your browser, with nothing to install and no account needed. A 6 V 1 W panel, the small epoxy kind in STEM kits, drives a load resistor with one meter on its current and one on its voltage. Drag the sunlight, change the load, and see why a solar panel does not behave like a battery. Start building free or put a regulator after it - 455 parts on the bench - 43 boards running now - 1.00x real time, on every board Click to open it in the editor The meters read about 161.8 mA and 5.99 V, about 0.97 W. Drag the panel’s sunlight slider, or click the circuit to open it in the editor and change the load. ## What you can do here In the circuit above, or in the editor it opens. - Drag the sunlight from full sun down to dark - Change the load and plot the panel’s current against its voltage - Find the load that takes the most power, the maximum power point - See why a panel is a current source and not a battery - Charge an 18650 cell from the panel through a TP4056 charger - Run a microcontroller from the panel and a cell ## What the running circuit shows The light sets the current; the load sets the voltage. In full sun, the slider at 1000 W/m², the panel gives about 161.8 mA into 36 ohms at about 5.99 V: about 0.97 W, near its 1 W rating. The amps meter’s 1 ohm shunt is in series, so the panel sees 37 ohms. Take the load away and the panel reads its open-circuit voltage, about 7.18 V. Make the load 1 ohm and the current is about 199.6 mA, almost the whole 0.2 A it gives into a short, at only 0.40 V. That is the shape of every solar cell: nearly the same current from a short up to about 5.5 V, then the voltage climbs the last stretch to 7.2 V as the cells’ own diode takes the current back. Power is current times voltage, so it is small at both ends. 10 ohms gets almost the full 0.2 A at 2.17 V, about 0.43 W, and 100 ohms gets 6.89 V at 68 mA, about 0.47 W. Between them is the maximum power point, near 33 ohms here, where the panel gives about 0.99 W. Drag the sunlight to 500 and the current the panel can give halves, to about 0.1 A, while the open-circuit voltage barely moves, to about 6.70 V. Now 36 ohms gets only about 0.34 W, while 56 ohms gets about 0.44 W: in dimmer light the best load is a bigger resistance. That moving target is why solar chargers with maximum power point tracking exist. ## How the panel is modeled A current source and a diode, fitted to the listing. Like a real cell, the panel is a current source set by the light with a diode across it, here twelve cells in series. The diode is fitted to what these panels are sold with: 7.2 V open, 0.2 A into a short and 1 W at 6 V. That fit comes from a product listing, not a datasheet, since most small panels are sold without one. The meters load the circuit the way real ones do: a 10 megohm input on volts and a 1 ohm shunt on amps. What it leaves out: temperature, which costs a hot panel about half a percent of its voltage a degree; the angle of the sun, so tilting the panel does nothing here; partial shading; and a blocking diode, which is a separate part you can add. For a whole project, the Solar sensor node example charges an 18650 from the same panel through a TP4056 and runs a Pro Mini from it, and the Solar tracker example steers a panel with four light sensors and two servos. The voltage regulator simulator The series and parallel circuit simulator The multimeter simulator Ohm’s law, running ## Questions Is it free? Yes. The circuit on this page, every part in it and the editor it opens in are on the free plan, with no card. Do I need an account? No. The circuit runs the moment the page does, and the editor opens without one. A free account is only for saving a project to the cloud and sharing it by link. Why does my solar panel read 7 V but give less under load? Because 7 V is its open-circuit voltage, with no current flowing. A panel is a current source: under load it gives what the light makes, about 0.2 A for this one in full sun, at whatever voltage the load sets. Into 36 ohms that is about 6 V. What is the maximum power point of a solar panel? The load at which the panel gives the most power, where current times voltage is largest. For this 6 V 1 W panel in full sun it is near 33 ohms, about 0.99 W. At half sun it moves to a larger resistance, around 60 ohms. Can I charge a battery from a solar panel? Yes, through a charger. Put a TP4056 between the panel and an 18650 cell; the charger stops at 4.2 V. Wiring a lithium cell straight to a panel is how cells get overcharged. ## More simulators Each one opens on a circuit that is already running. Online circuit simulator Breadboard simulator ESP32 simulator Op-amp simulator Logic gate simulator LED circuit simulator Servo simulator LCD simulator OLED simulator NeoPixel simulator 7 segment display simulator LED matrix simulator Stepper motor simulator Motor driver simulator Ultrasonic sensor simulator Rectifier simulator Digital circuit simulator Potentiometer simulator PWM simulator Relay simulator Shift register simulator DHT11 simulator RFID simulator Accelerometer simulator RGB LED simulator Buzzer simulator MOSFET simulator Circuit simulator for kids Flip-flop simulator Multiplexer simulator Full adder simulator I2C simulator UART simulator Thermistor simulator PIR sensor simulator Oscilloscope simulator Multimeter simulator DC motor simulator Traffic light simulator Diode simulator Capacitor simulator Series and parallel circuit simulator Wheatstone bridge simulator Voltage regulator simulator Soil moisture sensor simulator Zener diode simulator AC circuit simulator Thevenin simulator Decoder simulator Encoder simulator PID simulator Robot arm simulator Load cell simulator IR sensor simulator LM35 simulator HC-05 Bluetooth simulator nRF24L01 simulator ## Put a panel in the sun Open the circuit, drag the sunlight and change the load until the power peaks. Nothing to install, and no account needed. Start building free Open the editor