Source: https://mokxi.com/parts/tmp36 Updated: 2026-11-14 Part # Temperature sensor, TMP36 Half a volt at zero degrees and 10 mV a degree. Drag the slider to change the weather. See every part - 3 pins - 2 settings - In 3 projects - In 2 lessons Drawn live by the editor's own code, at the size you see it. At a glance ## The Temperature sensor, TMP36 in brief What it is, and every setting the properties panel gives it. The TMP36 is Analog Devices’ three-legged temperature sensor in a TO-92 package, sold bare in nearly every starter kit. Flat face toward you, legs down, the pins are VS, VOUT and GND; it runs from 2.7 to 5.5 volts, so VS goes to 5 V on an Uno or 3.3 V on an ESP32, and VOUT to any analog input, A0 on an Uno or an ADC1 pin such as GPIO 34 on an ESP32. VOUT is 500 mV at 0 °C plus 10 mV per degree, so 25 °C is 750 mV and -10 °C is 400 mV, which is how it reads below freezing on one supply. Mokxi models exactly that line, with offset and slope as properties (set offset to 0 and it behaves as an LM35), a slider from -40 to 125 °C that starts at 22.5, a 100 ohm output, and an output that goes high impedance below 2.7 volts of supply. The classic mistake is converting it LM35-style, with no offset, which reads 50 degrees too hot. Self-heating, settling time, noise and the real part’s ±2 °C error are not modeled. Family Sensors Pins 3 offset 500 500 mV by default (a TMP36). Setting it to 0 gives an LM35's output, but for an LM35 use the LM35 part, which also has its 4 V minimum supply. slope 10 10 mV per degree by default. Pins ## 3 pins Named as the editor names them, so a wire lands where you expect it. Pin What it does VS Supply, 2.7 V or more. VOUT offset + slope x temperature. GND Ground. How to use it ## How to use the TMP36 with an Arduino Hold it flat face toward you, legs down: left is VS to 5 V, the middle is VOUT to A0, and right is GND. In the love meter the TMP36 stands in the breadboard that way, with VS and GND on the top rails and VOUT on A0 beside a bar of ten WS2812B LEDs. The sketch turns the count into millivolts with analogRead(A0) * 5000L / 1024 and takes 500 off, because the TMP36 is 500 mV at 0 °C and 10 mV a degree after that, so what is left is tenths of a degree. It averages the room for two seconds first and lights one LED for every half degree above it. Drag the sensor’s slider up as if you were holding it. Forget the 500 mV offset and you read 50 degrees too hot: that is the LM35’s formula, and the two parts are not interchangeable in code. Part pin Board pin VS 5 V VOUT A0 GND GND It runs from 2.7 V, so on an ESP32 power VS from 3.3 V, read VOUT on an ADC1 pin such as GPIO 34, and convert with 3300 and 4096 in place of 5000 and 1024. Click to open it in the editor This is the simulator itself, running here. Click anything to open it in the editor. Open this project in the editor Read the full tutorial Tenths of a degree from a TMP36 How it is modeled ## What is true about the Temperature sensor, TMP36, here In its help article’s own words: what the simulation gets right, and where it stops. ### Modeled Below 2.7 V across VS and GND the part is not running and VOUT is high impedance, exactly what an unpowered sensor does. The output is a low-impedance source clamped to the rails, so a sensor on a 3.3 V board cannot read above 3.3 V; the datasheet's 125 degree top of range simply is not reachable there, which is true of the real part too. ### Not modeled No self-heating, no settling time, no noise, and no datasheet accuracy error. The temperature you set is the temperature that comes back, which makes a demo a demo rather than a calibration exercise. A real TMP36 is ±1 °C at 25 °C and ±2 °C over its range, and the straight line here has none of that. VOUT drives through 100 ohms, which is a stand-in rather than a datasheet figure: a real TMP36 has a much lower output impedance but can only source about 50 µA, and neither the impedance nor the current limit is what the number represents. It is there so a load on the output is not free. There is no supply-current draw, no supply rejection, and no way to overload the output. It simply behaves as a 100 ohm source however much current is taken from it. From TMP36 temperature sensor, in full. Projects ## See the Temperature sensor, TMP36 in a project 3 built-in projects use it. Each opens in the editor, already wired. Lessons ## Where it turns up in a lesson 2 lessons place it in their own circuits. ### Learn articles 2 lessons - Arduino TMP36 Temperature Sensor in °F and °C - Tinkercad Alternatives: 6 Simulators, Compared Boards ## The boards it is shown on This board has a built-in project with the Temperature sensor, TMP36 in it. - Arduino Uno R3 More parts ## The rest of the bench Every one of these is drawn and simulated the same way. Full-size breadboard A real 0.1 inch grid with the rails and the center channel, 63 columns wide. Jumper wires Drag from any pin or hole to any other. Corners snap, and you can drag them. Power A supply rail at the voltage you choose. Ground The other end of every circuit. LED Lights when current flows. Five colors, and the brightness is what your eye would see. Filament lamp A tungsten bulb in a holder: an inrush when it is switched on cold, tens of milliseconds to warm up, and dim on half its voltage. Resistor Any value you like, with the color bands drawn to match. ESP32-C3-DevKitM-1 A RISC-V board that runs your firmware at 160 MHz on the real memory map. Pushbutton A 12 mm tactile switch. Hold it while the simulation runs. Raspberry Pi Pico The RP2040 board on our own Cortex-M0+ core. Pick a program and press Run. Raspberry Pi Pico W Raspberry Pi Pico W (RP2040). The same board and the same pinout as a Pico, with the CYW43439 on it. The WiFi is simulated (no radio; real internet through the Cloud panel’s switch), and the on-board LED, which hangs off that chip rather than off GP25, is driven through the same path. Everything else is the Pico. Raspberry Pi 4 Model B Raspberry Pi 4 Model B: the 40-pin header, driven by main.py with RPi.GPIO or gpiozero. See every part ## Wire up the Temperature sensor, TMP36 Open the editor and push it into the breadboard. It is free, and it runs on your own machine. Start building free Open the editor