Source: https://mokxi.com/parts/solenoid
Updated: 2026-11-16

Part

# Solenoid

A coil and a plunger. It needs a transistor, and a diode across it for the kick when it lets go.

See every part

- 2 pins
- 8 settings
- In 7 projects
- In 1 lesson

Drawn live by the editor's own code, at the size you see it.

At a glance

## The Solenoid in brief

What it is, and every setting the properties panel gives it.

A push-pull solenoid is a coil around a steel plunger that is pulled in while current flows and springs back out when it stops. It is the simplest actuator there is, and the part that teaches the flyback diode, because it is an inductor with a moving core. The Mokxi coil is an inductance in series with its winding resistance, solved in the circuit’s matrix, so the current builds with the L over R time constant and the kick when it is switched off comes out of the same equations. The default is a 12 V coil of 40 ohms and 30 mH, which draws 300 mA, far more than a pin gives. The plunger moves in when the current passes 75 percent of rated and releases at 15 percent, with a travel time each way. Two named models are included, a 12 V door lock and a 12 V water valve. The way the inductance rises as the plunger closes, the force over the stroke and heat are not modeled.

Family

Outputs

Pins

2

model

custom (or 12V door lock, 12V water valve)

voltage

12

resistance

40

inductance

30

pull

0.75

release

0.15

pull_ms

15

release_ms

10

Pins

## 2 pins

Named as the editor names them, so a wire lands where you expect it.

Pin

What it does

1

The two ends of the coil. It has no polarity.

2

The two ends of the coil. It has no polarity.

How to use it

## How to drive a solenoid from an Arduino

A pin cannot drive the coil: it draws 300 mA at 12 V for the default part. So the pin goes to the gate of a logic-level MOSFET, an IRLZ44N in the project, and the transistor switches the coil. One coil lead goes to the 12 V supply, the other to the drain, the source goes to ground shared with the Uno, and a 1N4007 diode sits across the coil with its cathode on the supply side. The sketch then taps once a second, HIGH to pull the plunger in and LOW to let it go.

The diode is the point of the circuit. A coil’s current cannot stop at once. When the MOSFET turns off, the coil keeps pushing and the voltage at the drain climbs until something conducts. With no diode that is the transistor itself, at hundreds of volts. With the diode the current circulates through the coil and diode, the drain sits one drop above the supply, and the current dies away over a few milliseconds. Put a meter on the drain, remove the diode, and watch.

The coil has no polarity, so either lead can go either way. Change the model to the door lock, 18.5 ohms and 650 mA, and the same driver now has to carry twice the current. The lock is rated for 1 to 10 seconds on at a time, which the simulator does not enforce.

Part pin

Board pin

Coil lead 1

The 12 V supply and the diode’s cathode

Coil lead 2

The MOSFET’s drain and the diode’s anode

MOSFET gate

Uno pin 9

MOSFET source

Ground, shared with the Uno

Supply minus

Ground

A 3.3 V board needs a MOSFET that is fully on at 3.3 V, so check the gate threshold, or use a driver module, before trusting the part number.

Click to open it in the editor

This is the simulator itself, running here. Click anything to open it in the editor.

Open this project in the editor Read the full tutorial

A sketch that taps once a second

Common errors

## Common Solenoid errors and fixes

What goes wrong

The fix

The driving transistor is destroyed after a few taps.

There is no diode across the coil. Add one, cathode to the supply side, so the current has somewhere to go when the transistor turns off.

The solenoid buzzes or barely moves.

The coil needs 75 percent of its rated current to pull in. A 12 V coil on 5 V or through a transistor that is only half on will not make it. Use a logic-level MOSFET and the rated supply.

A pin drives the coil directly and the Uno resets or the plunger stays out.

300 mA is far beyond a pin’s limit. Drive the coil through a MOSFET or a TIP120 and join the grounds of the supply and the board.

The plunger releases late.

The diode slows the release, as it does on a bench: the current decays through the diode over several milliseconds. A faster release needs a Zener in series with the diode, at the cost of a bigger kick.

Questions

## Questions and answers

### Why does a solenoid need a diode?

A coil’s current cannot stop at once, so switching it off makes a voltage spike at the switched end. The diode gives the current a path, keeping the spike to one diode drop above the supply.

### Can an Arduino pin drive a solenoid directly?

No. The default 12 V coil draws 300 mA, and a pin gives a small fraction of that. Use a logic-level MOSFET such as the IRLZ44N.

### What do the pull and release settings mean?

They are the fractions of the rated current at which the plunger starts in (0.75) and starts back out (0.15). pull_ms and release_ms set how long each travel takes.

### Does it model the force of the plunger?

No. The model gives the current build-up, the kick on switch-off and the plunger’s on or off state. The force over the stroke, heat in an overdriven coil and what the plunger hits are not modeled.

How it is modeled

## What is true about the Solenoid, here

In its help article’s own words: what the simulation gets right, and where it stops.

### Modeled

The coil is an inductance in series with its winding resistance, solved in the
circuit's matrix, so the current builds with the L/R time constant and the kick
on switch-off comes out of the same equations. The plunger follows the "must
operate" and release figures small solenoid datasheets give, with a travel time
each way. A diode across the coil slows the release, as it does on the bench.

### Not modeled

The inductance rising as the plunger closes the gap (the dip in the current that
tells a driver the plunger moved), the force over the stroke, heat in an
overdriven coil, and whatever the plunger hits.

From Solenoid, in full.

Projects

## See the Solenoid in a project

7 built-in projects use it. Each opens in the editor, already wired.

Lessons

## Where it turns up in a lesson

One lesson places it in its own circuit.

### Learn articles

1 lesson

- ULN2003 Simulator: Darlington Driver and COM Pin

Boards

## The boards it is shown on

This board has a built-in project with the Solenoid in it.

- Arduino Uno R3

Keep going

## Keep going

- NPN Transistor as a Switch: a 2N2222 and an Arduino
- Arduino MOSFET Module: Why the IRF520 Is Half On
- Diode
- Transistor (NPN or PNP)
- Relay module

More parts

## The rest of the bench

Every one of these is drawn and simulated the same way.

Full-size breadboard

A real 0.1 inch grid with the rails and the center channel, 63 columns wide.

Jumper wires

Drag from any pin or hole to any other. Corners snap, and you can drag them.

Power

A supply rail at the voltage you choose.

Ground

The other end of every circuit.

LED

Lights when current flows. Five colors, and the brightness is what your eye would see.

Filament lamp

A tungsten bulb in a holder: an inrush when it is switched on cold, tens of milliseconds to warm up, and dim on half its voltage.

Resistor

Any value you like, with the color bands drawn to match.

ESP32-C3-DevKitM-1

A RISC-V board that runs your firmware at 160 MHz on the real memory map.

Pushbutton

A 12 mm tactile switch. Hold it while the simulation runs.

Raspberry Pi Pico

The RP2040 board on our own Cortex-M0+ core. Pick a program and press Run.

Raspberry Pi Pico W

Raspberry Pi Pico W (RP2040). The same board and the same pinout as a Pico, with the CYW43439 on it. The WiFi is simulated (no radio; real internet through the Cloud panel’s switch), and the on-board LED, which hangs off that chip rather than off GP25, is driven through the same path. Everything else is the Pico.

Raspberry Pi 4 Model B

Raspberry Pi 4 Model B: the 40-pin header, driven by main.py with RPi.GPIO or gpiozero.

See every part

## Wire up the Solenoid

Open the editor and push it into the breadboard. It is free, and it runs on your own machine.

Start building free Open the editor
