Source: https://mokxi.com/parts/rf433tx
Updated: 2026-11-17

Part

# RF transmitter, FS1000A

DATA high is the 433 MHz carrier on: rc-switch or RH_ASK sends, and every receiver on the canvas hears it.

See every part

- 4 pins
- In 1 project

Drawn live by the editor's own code, at the size you see it.

At a glance

## The RF transmitter, FS1000A in brief

What it is, and where it sits on the bench.

The FS1000A is the 433 MHz transmitter half of the pair in nearly every Arduino kit: a SAW resonator and one transistor, with no chip, so DATA high switches the carrier on and DATA low switches it off. Its pins are DATA, VCC and GND along the bottom, on 3 to 12 V, plus an ANT pad for a 17 cm wire. A 3.3 V or 5 V board pin keys it, and a library makes every pulse: rc-switch sends remote-socket codes with send(5393, 24), RadioHead’s RH_ASK sends checked messages from pin 12. In Mokxi the ANT pad of every 433 MHz module joins one shared air, so each XY-MK-5V receiver on the canvas hears every transmitter with no wire, and two sending at once spoil each other’s codes. Distance, walls and the antenna are not modeled.

Family

Clocks and links

Pins

4

Pins

## 4 pins

Named as the editor names them, so a wire lands where you expect it.

Pin

Role

What it does

DATA

Input

High switches the 433.92 MHz carrier on, low switches it off. A 3.3 V or a 5 V board pin drives it.

VCC

Input or output

Supply, 3 to 12 V. More volts is more range on a real one.

GND

Input or output

Ground.

ANT

Output

The antenna pad, and the air every 433 MHz module on the canvas shares. Leave it unwired.

How to use it

## How to use the FS1000A 433 MHz transmitter with an Arduino

Wire VCC to 5 V, GND to GND and DATA to any digital pin, and leave the antenna pad alone. The module has no chip: DATA high switches the 433 MHz carrier on and low switches it off, so a library makes every pulse of a code for you.

With rc-switch, call enableTransmit(10) once in setup() and send(code, 24) to send a 24-bit code, the kind remote sockets and doorbells use; send() repeats it so a receiver can check it. Every receiver on the canvas hears every transmitter, with no wire between them, so the receiving board is wired only to its own XY-MK-5V.

Part pin

Board pin

VCC

5 V

DATA

Pin 10

GND

GND

The same code runs on an ESP32 or a Pico; a 3.3 V pin drives DATA. On a real one, more volts on VCC (up to 12 V) and a 17 cm wire on the antenna pad give more range.

Click to open it in the editor

This is the simulator itself, running here. Click anything to open it in the editor.

Open this project in the editor Read the full tutorial

Send a 24-bit code with rc-switch

How it is modeled

## What is true about the RF transmitter, FS1000A, here

In its help article’s own words: what the simulation gets right, and where it stops.

### Not modeled

Distance, walls and the antenna: every receiver on the canvas hears every transmitter at full strength. That is right for a desk; the real pair reaches about 20 to 100 m in the open with a 17 cm wire on ANT. The 315 MHz version is the same part on another frequency, and here all modules share one. The carrier switches at once, where a real one takes some tens of microseconds, and the supply current (about 10 to 40 mA while sending) is not drawn.

From 433 MHz transmitter, FS1000A, in full.

Projects

## See the RF transmitter, FS1000A in a project

One built-in project uses it. It opens in the editor, already wired.

Boards

## The boards it is shown on

This board has a built-in project with the RF transmitter, FS1000A in it.

- Arduino Uno R3

Libraries

## Arduino libraries for the RF transmitter, FS1000A

Built in, so the sketch compiles with nothing to install. Each page has the calls, the wiring and an example to run.

- RadioHead
- rc-switch

More parts

## The rest of the bench

Every one of these is drawn and simulated the same way.

Full-size breadboard

A real 0.1 inch grid with the rails and the center channel, 63 columns wide.

Jumper wires

Drag from any pin or hole to any other. Corners snap, and you can drag them.

Power

A supply rail at the voltage you choose.

Ground

The other end of every circuit.

LED

Lights when current flows. Five colors, and the brightness is what your eye would see.

Filament lamp

A tungsten bulb in a holder: an inrush when it is switched on cold, tens of milliseconds to warm up, and dim on half its voltage.

Resistor

Any value you like, with the color bands drawn to match.

ESP32-C3-DevKitM-1

A RISC-V board that runs your firmware at 160 MHz on the real memory map.

Pushbutton

A 12 mm tactile switch. Hold it while the simulation runs.

Raspberry Pi Pico

The RP2040 board on our own Cortex-M0+ core. Pick a program and press Run.

Raspberry Pi Pico W

Raspberry Pi Pico W (RP2040). The same board and the same pinout as a Pico, with the CYW43439 on it. The WiFi is simulated (no radio; real internet through the Cloud panel’s switch), and the on-board LED, which hangs off that chip rather than off GP25, is driven through the same path. Everything else is the Pico.

Raspberry Pi 4 Model B

Raspberry Pi 4 Model B: the 40-pin header, driven by main.py with RPi.GPIO or gpiozero.

See every part

## Wire up the RF transmitter, FS1000A

Open the editor and push it into the breadboard. It is free, and it runs on your own machine.

Start building free Open the editor
