Source: https://mokxi.com/parts/rf433rx
Updated: 2026-11-17

Part

# RF receiver, XY-MK-5V

Hears every FS1000A on the canvas, and hisses random noise when nothing sends, like the real one.

See every part

- 5 pins
- 1 setting
- In 1 project

Drawn live by the editor's own code, at the size you see it.

At a glance

## The RF receiver, XY-MK-5V in brief

What it is, and every setting the properties panel gives it.

The XY-MK-5V is the 433 MHz receiver half of the kit pair: a superregenerative receiver and an LM358 that turns the carrier into a logic level on DATA, high while a transmitter’s carrier is on. Its pins are VCC, DATA, DATA and GND, the two DATA pins one line, rated for 5 V; the LM358’s high stops about 1.5 V short of VCC, so on 3.3 V it is too weak for a 3.3 V board. With nothing sending it has no squelch and DATA toggles at random, which Mokxi models after 20 ms without a carrier. That noise is why rc-switch takes a code only after it arrives twice and RH_ASK waits for a preamble, a start symbol and a CRC. Use enableReceive(0) for pin 2 on an Uno, or RH_ASK on pin 11.

Family

Clocks and links

Pins

5

noise

true

Pins

## 5 pins

Named as the editor names them, so a wire lands where you expect it.

Pin

Role

What it does

VCC

Input or output

Supply. Rated 5 V; it works from 3 V with a weak high on DATA.

DATA

Output

High while a carrier is heard, low while not.

DATA2

Output

GND

Input or output

Ground.

ANT

Input

The antenna pad, and the air every 433 MHz module on the canvas shares. Leave it unwired.

How to use it

## How to use the XY-MK-5V 433 MHz receiver with an Arduino

Wire VCC to 5 V, GND to GND and either DATA pin to pin 2, the Uno’s interrupt 0, and leave the antenna pad alone. DATA is high while a carrier is heard; between codes it is random noise, as on a real bench, which the logic analyzer shows.

With rc-switch, call enableReceive(0) once in setup(), then check available() in loop() and read getReceivedValue(). rc-switch only takes a code that arrives twice the same way, so the noise never prints. Run it at 5 V: on 3.3 V the module’s high is under 2 V, which an ESP32 may read as low.

Part pin

Board pin

VCC

5 V

DATA

Pin 2

GND

GND

On an ESP32 or a Pico, pass the pin itself to enableReceive(). Give the module 5 V and put a divider on DATA, because those boards are not 5 V tolerant.

Click to open it in the editor

This is the simulator itself, running here. Click anything to open it in the editor.

Open this project in the editor Read the full tutorial

Print each code rc-switch hears

How it is modeled

## What is true about the RF receiver, XY-MK-5V, here

In its help article’s own words: what the simulation gets right, and where it stops.

### Not modeled

Distance, walls, signal strength and interference: every transmitter on the canvas is heard at full strength. The edges come out when the carrier switches, where a real one lags by some tens of microseconds and its pulse widths wander. The tuning coil is assumed set to 433.92 MHz.

From 433 MHz receiver, XY-MK-5V, in full.

Projects

## See the RF receiver, XY-MK-5V in a project

One built-in project uses it. It opens in the editor, already wired.

Boards

## The boards it is shown on

This board has a built-in project with the RF receiver, XY-MK-5V in it.

- Arduino Uno R3

Libraries

## Arduino libraries for the RF receiver, XY-MK-5V

Built in, so the sketch compiles with nothing to install. Each page has the calls, the wiring and an example to run.

- RadioHead
- rc-switch

More parts

## The rest of the bench

Every one of these is drawn and simulated the same way.

Full-size breadboard

A real 0.1 inch grid with the rails and the center channel, 63 columns wide.

Jumper wires

Drag from any pin or hole to any other. Corners snap, and you can drag them.

Power

A supply rail at the voltage you choose.

Ground

The other end of every circuit.

LED

Lights when current flows. Five colors, and the brightness is what your eye would see.

Filament lamp

A tungsten bulb in a holder: an inrush when it is switched on cold, tens of milliseconds to warm up, and dim on half its voltage.

Resistor

Any value you like, with the color bands drawn to match.

ESP32-C3-DevKitM-1

A RISC-V board that runs your firmware at 160 MHz on the real memory map.

Pushbutton

A 12 mm tactile switch. Hold it while the simulation runs.

Raspberry Pi Pico

The RP2040 board on our own Cortex-M0+ core. Pick a program and press Run.

Raspberry Pi Pico W

Raspberry Pi Pico W (RP2040). The same board and the same pinout as a Pico, with the CYW43439 on it. The WiFi is simulated (no radio; real internet through the Cloud panel’s switch), and the on-board LED, which hangs off that chip rather than off GP25, is driven through the same path. Everything else is the Pico.

Raspberry Pi 4 Model B

Raspberry Pi 4 Model B: the 40-pin header, driven by main.py with RPi.GPIO or gpiozero.

See every part

## Wire up the RF receiver, XY-MK-5V

Open the editor and push it into the breadboard. It is free, and it runs on your own machine.

Start building free Open the editor
