Source: https://mokxi.com/parts/mb102
Updated: 2026-11-16

Part

# Breadboard power supply, MB102

The Elegoo kit power module: a 9 V battery on its jack, 5 V or 3.3 V on each pair of rails by jumper.

See every part

- 8 pins
- 3 settings
- In 1 project

Drawn live by the editor's own code, at the size you see it.

At a glance

## The Breadboard power supply, MB102 in brief

What it is, and every setting the properties panel gives it.

The MB102 is the small green starter kit board that plugs into both pairs of rails at the end of a breadboard. It takes a 9 volt battery or a 6.5 to 12 volt adapter on its barrel jack, or 5 volts from its USB socket, and a jumper on each side puts 5 V, 3.3 V or nothing on that pair of rails. Mokxi models the two real regulators: the jack feeds an AMS1117-5.0 and the 5 volt net feeds an AMS1117-3.3, with about a volt of dropout and a current limit near an amp, so a 9 volt battery gives a solid 5 volts, four fresh AA cells just manage it at a light load, and three leave both rails short. Clicking the module works its power switch. Wired with an Arduino, share the ground and nothing else: joining the module’s 5 V to the Uno’s 5V pin sets two supplies fighting over one rail, and leaving out the ground wire makes a servo twitch. Heat and reversed polarity on the jack are not modeled.

Family

Power and wiring

Pins

8

top

5V (or 3.3V, off)

bottom

5V (or 3.3V, off)

usb

false

Pins

## 8 pins

Named as the editor names them, so a wire lands where you expect it.

Pin

What it does

VIN

The barrel jack's center: the battery or supply's plus.

GND

The jack's sleeve, and the board's ground.

5V

A header pin on the 5 V net, for a jumper wire.

3V3

A header pin on the 3.3 V net.

TOP+

Into the first holes of the top pair of rails.

TOP-

Into the first holes of the top pair of rails.

BOT+

Into the first holes of the bottom pair.

BOT-

Into the first holes of the bottom pair.

How to use it

## How to use the MB102 power module with an Arduino

Stand the module on the left end of the breadboard with TOP+ in the first hole of the top red rail, so all four rail pins land in their rails. Feed the jack from a 9 V battery, set the top jumper to 5V and the bottom one to 3.3V, and put the servo on the top rails.

The Uno shares only its ground and the servo’s signal on pin 9. Its 5V pin stays off the module’s rails, so the two supplies never fight. Click the module while it runs and both rails go dead. Forget the ground wire instead and the servo’s signal has no reference, so it twitches or does nothing.

Part pin

Board pin

VIN

9 V battery V+

GND

9 V battery V-

TOP+ (5 V rail)

Servo VCC

TOP- (ground rail)

Servo GND and Uno GND

BOT+ (3.3 V rail)

A0

Hold the button

This is the simulator itself, running here. Click anything to open it in the editor.

Open this project in the editor Read the full tutorial

The servo on pin 9, and A0 watching the 3.3 V rail

How it is modeled

## What is true about the Breadboard power supply, MB102, here

In its help article’s own words: what the simulation gets right, and where it stops.

### Modeled

Two real regulators. The jack feeds an AMS1117-5.0 and the 5 V net feeds an
AMS1117-3.3, both the bench's regulator model with the
AMS1117 card: about a volt of dropout, an amp of current limit, 5 mA of bias. A
9 V battery gives a solid 5 V; four fresh AA cells (6.4 V) just manage it at a
light load; three cells leave both rails short, because the 3.3 V side runs off
the 5 V net.

The loads add up. Everything on the 3.3 V rail comes through the 5 V regulator
too, and a short on either rail is held to about an amp.

The battery's own resistance. A 9 V battery is a volt and a half of sag at
an amp, so heavy loads on a battery-fed module drop out sooner than on a wall
supply.

USB puts 5 V from the socket on the 5 V net, and the 5 V regulator has nothing to
do.

The switch cuts both the jack and USB, and the rails go dead.

### Not modeled

Heat: the 5 V regulator turning 9 V into 5 V at 300 mA burns 1.2 W, and a long
stall gets the SOT-223 too hot to touch, which here never happens. Reversed
polarity on the jack, which on most copies destroys the regulators. The power
LED is drawn as its current only, and the 3.3 V net carries a third of a milliamp
of bleed so it always has a load.

From Breadboard power supply (MB102), in full.

Projects

## See the Breadboard power supply, MB102 in a project

One built-in project uses it. It opens in the editor, already wired.

Boards

## The boards it is shown on

This board has a built-in project with the Breadboard power supply, MB102 in it.

- Arduino Uno R3

More parts

## The rest of the bench

Every one of these is drawn and simulated the same way.

Full-size breadboard

A real 0.1 inch grid with the rails and the center channel, 63 columns wide.

Jumper wires

Drag from any pin or hole to any other. Corners snap, and you can drag them.

Power

A supply rail at the voltage you choose.

Ground

The other end of every circuit.

LED

Lights when current flows. Five colors, and the brightness is what your eye would see.

Filament lamp

A tungsten bulb in a holder: an inrush when it is switched on cold, tens of milliseconds to warm up, and dim on half its voltage.

Resistor

Any value you like, with the color bands drawn to match.

ESP32-C3-DevKitM-1

A RISC-V board that runs your firmware at 160 MHz on the real memory map.

Pushbutton

A 12 mm tactile switch. Hold it while the simulation runs.

Raspberry Pi Pico

The RP2040 board on our own Cortex-M0+ core. Pick a program and press Run.

Raspberry Pi Pico W

Raspberry Pi Pico W (RP2040). The same board and the same pinout as a Pico, with the CYW43439 on it. The WiFi is simulated (no radio; real internet through the Cloud panel’s switch), and the on-board LED, which hangs off that chip rather than off GP25, is driven through the same path. Everything else is the Pico.

Raspberry Pi 4 Model B

Raspberry Pi 4 Model B: the 40-pin header, driven by main.py with RPi.GPIO or gpiozero.

See every part

## Wire up the Breadboard power supply, MB102

Open the editor and push it into the breadboard. It is free, and it runs on your own machine.

Start building free Open the editor
