Source: https://mokxi.com/parts/max6675
Updated: 2026-11-19

Part

# Thermocouple converter, MAX6675

A K-type thermocouple on SPI, a quarter degree a count up to 1023. Read it no faster than four times a second.

See every part

- 5 pins
- 2 settings
- In 1 project
- In 1 lesson

Drawn live by the editor's own code, at the size you see it.

At a glance

## The Thermocouple converter, MAX6675 in brief

What it is, and every setting the properties panel gives it.

The MAX6675 board is the usual way to put a K-type thermocouple on an Arduino: the probe of kilns, smokers, reflow ovens and 3D printer hot ends. A thermocouple makes only tens of microvolts per degree, far below what a board’s ADC can see, so the MAX6675 amplifies it, corrects for the temperature of its own screw terminals and sends the result over a read-only SPI line as twelve bits at a quarter degree each, up to 1023 °C. On the Mokxi bench a slider sets the probe tip from 0 to 1000 °C, and a property takes the probe off the terminals. The model clocks out sixteen bits per read, flags an open thermocouple, keeps SO high impedance while CS is high and takes 0.22 s per conversion after CS rises, so a sketch that reads faster just sees the same number again, as it would with the real chip.

Family

Sensors

Pins

5

temperature

25

probe

true

Pins

## 5 pins

Named as the editor names them, so a wire lands where you expect it.

Pin

Role

What it does

GND

Input or output

Ground.

VCC

Input or output

Supply, 3.0 to 5.5 V.

SCK

Input

The clock, from the board.

CS

Input

Low to read. Its rising edge starts the next conversion.

SO

Output

The data out, high-Z while CS is high.

How to use it

## How to read a MAX6675 thermocouple with an Arduino

Five wires: VCC to 5 V, GND to ground, and the three signal pins to any digital pins, here SCK to 6, CS to 5 and SO to 4. SO is the chip’s output, so it goes to an input, never to MOSI. The thermocouple itself screws into the board’s terminals; on the canvas it is already in place.

The library takes the three pins in the order SCK, CS, SO and does the clocking itself. Give the chip half a second after power-up to finish its first conversion, then call readCelsius() no more than about four times a second. The thermocouple project reads twice a second and prints Celsius and Fahrenheit. Drag the slider and the next line follows; untick the probe property and readCelsius() returns NAN, which the sketch reports as no thermocouple.

Part pin

Board pin

VCC

5 V

GND

GND

SCK

Pin 6

CS

Pin 5

SO

Pin 4

The chip runs from 3.0 to 5.5 V, so on an ESP32 or a Pico power it from 3.3 V and pick any three free GPIO pins.

Click to open it in the editor

This is the simulator itself, running here. Click anything to open it in the editor.

Open this project in the editor Read the full tutorial

Reading it, from the thermocouple sketch

Common errors

## Common Thermocouple converter, MAX6675 errors and fixes

What goes wrong

The fix

The temperature repeats the same value line after line.

A conversion takes 0.22 s after CS rises, and a read before it ends returns the last result. Wait at least a quarter of a second between reads.

readCelsius() returns NAN.

The chip sees no thermocouple on its terminals. Check the probe’s connection; in the simulator, check that the probe property is ticked.

Every read returns 0 or garbage.

SO is wired to MOSI or swapped with SCK. SO is the chip’s data output and goes to an input pin; pass the pins to the constructor in the order SCK, CS, SO.

A freezer probe reads 0 °C.

The MAX6675 does not report below 0 °C. Use a sensor made for cold, such as a DS18B20, for that range.

Questions

## Questions and answers

### What is the highest temperature the MAX6675 can read?

1023.75 °C, the top of its twelve bits at a quarter degree each. The slider on the part goes to 1000 °C.

### Can the MAX6675 share SPI with other devices?

Yes. SCK and SO can be shared; each device gets its own CS, and the MAX6675 leaves SO high impedance while its CS is high.

### Why does the first reading come out wrong?

The chip needs a conversion, 0.22 s, before it has anything to give. That is why the sketch waits half a second in setup().

### How accurate is a MAX6675 reading?

The chip is specified to within a few degrees, and the thermocouple adds its own error. The simulation reports the slider exactly, at the chip’s quarter-degree step.

How it is modeled

## What is true about the Thermocouple converter, MAX6675, here

In its help article’s own words: what the simulation gets right, and where it stops.

### Modeled

From the MAX6675 datasheet: CS low puts bit 15 on SO and each falling edge of
SCK the next bit, sixteen in all; the temperature in bits 14 to 3 at 0.25
degrees a count; bit 2 set for an open thermocouple; SO high-Z while
deselected. A conversion takes 0.22 s after CS rises, and a read before it
finishes returns the last result, so reading faster than about four times a
second repeats the same number.

### Not modeled

The thermocouple's own voltage and the chip's accuracy (plus or minus 2 degrees),
temperatures below 0 (the chip reads 0), and the 4.3 MHz clock limit.

From MAX6675 thermocouple converter, in full.

Projects

## See the Thermocouple converter, MAX6675 in a project

One built-in project uses it. It opens in the editor, already wired.

Lessons

## Where it turns up in a lesson

One lesson places it in its own circuit.

### Learn articles

1 lesson

- Arduino MAX6675 Thermocouple: Wiring and Code

Boards

## The boards it is shown on

This board has a built-in project with the Thermocouple converter, MAX6675 in it.

- Arduino Uno R3

Libraries

## Arduino libraries for the Thermocouple converter, MAX6675

Built in, so the sketch compiles with nothing to install. Each page has the calls, the wiring and an example to run.

- MAX6675 library

Keep going

## Keep going

- SPI Explained: Clock, Data and Chip Select
- Arduino Temperature Data Logger Lab, Step by Step
- Temperature sensor, DS18B20
- IR thermometer, MLX90614
- NTC temperature sensor module

More parts

## The rest of the bench

Every one of these is drawn and simulated the same way.

Full-size breadboard

A real 0.1 inch grid with the rails and the center channel, 63 columns wide.

Jumper wires

Drag from any pin or hole to any other. Corners snap, and you can drag them.

Power

A supply rail at the voltage you choose.

Ground

The other end of every circuit.

LED

Lights when current flows. Five colors, and the brightness is what your eye would see.

Filament lamp

A tungsten bulb in a holder: an inrush when it is switched on cold, tens of milliseconds to warm up, and dim on half its voltage.

Resistor

Any value you like, with the color bands drawn to match.

ESP32-C3-DevKitM-1

A RISC-V board that runs your firmware at 160 MHz on the real memory map.

Pushbutton

A 12 mm tactile switch. Hold it while the simulation runs.

Raspberry Pi Pico

The RP2040 board on our own Cortex-M0+ core. Pick a program and press Run.

Raspberry Pi Pico W

Raspberry Pi Pico W (RP2040). The same board and the same pinout as a Pico, with the CYW43439 on it. The WiFi is simulated (no radio; real internet through the Cloud panel’s switch), and the on-board LED, which hangs off that chip rather than off GP25, is driven through the same path. Everything else is the Pico.

Raspberry Pi 4 Model B

Raspberry Pi 4 Model B: the 40-pin header, driven by main.py with RPi.GPIO or gpiozero.

See every part

## Wire up the Thermocouple converter, MAX6675

Open the editor and push it into the breadboard. It is free, and it runs on your own machine.

Start building free Open the editor
