Source: https://mokxi.com/parts/ili9341cap
Updated: 2026-11-16

Part

# Touch TFT, 2.8 inch ILI9341 with FT6206

The 2.8 inch color TFT with a capacitive touch panel: the display on SPI, the touch on I2C.

See every part

- 11 pins
- In 1 project

Drawn live by the editor's own code, at the size you see it.

At a glance

## The Touch TFT, 2.8 inch ILI9341 with FT6206 in brief

What it is, and where it sits on the bench.

This is the 2.8 inch 240x320 ILI9341 TFT with an FT6206 capacitive touch controller, laid out like Adafruit’s cap-touch breakout. Unlike the resistive ili9341touch, whose XPT2046 is a second SPI device with its own T_CS, the touch here is I2C at 0x38 on two extra pins with 4.7 k pull-ups on the board. Its eleven pins are VCC, GND, CS, RST, DC, MOSI, SCK, LED, MISO, SCL and SDA. On an Uno the display takes 13 and 11 with CS on 10, DC on 9 and RST on 8, and the touch takes A5 and A4; on an ESP32 DevKit, SPI on 18 and 23 and I2C on 21 and 22. The display is the ILI9341 model. The FT6206 answers FocalTech’s registers: chip ID 0x06, vendor ID 0x11, the touch count in 0x02 and a 12-bit point with its down, contact or lift flag, read in one burst. The point comes back the other way up from the display, (239 - x, 319 - y), so a sketch that skips the flip draws in the opposite corner, and setRotation() does not turn the film. A second finger, gestures, the threshold and the INT and RST lines are not modeled.

Family

Displays

Pins

11

Pins

## 11 pins

Named as the editor names them, so a wire lands where you expect it.

Pin

Role

What it does

VCC

Input or output

Supply.

GND

Input or output

Ground.

CS

Input

The display's SPI bus, as on the ILI9341.

RST

Input

The display's SPI bus, as on the ILI9341.

DC

Input

The display's SPI bus, as on the ILI9341.

MOSI

Input

The display's SPI bus, as on the ILI9341.

SCK

Input

The display's SPI bus, as on the ILI9341.

LED

Input or output

The backlight: low puts it out.

MISO

Output

The display's SPI bus, as on the ILI9341.

SCL

Input or output

The touch controller's I2C bus, address 0x38.

SDA

Input or output

The touch controller's I2C bus, address 0x38.

How to use it

## How to use a capacitive touch ILI9341 with an Arduino

Two buses on one board. The display is SPI: CS to pin 10, DC to 9, RST to 8, MOSI to 11 and SCK to 13, with VCC and LED on 5 V. The FT6206 touch controller is I2C at 0x38: SCL to A5 and SDA to A4. That is the difference from the resistive ILI9341 touch board, whose XPT2046 needs a chip select and an SPI bus of its own.

Call tft.begin() and ctp.begin(40), then in loop() check ctp.touched() and read ctp.getPoint(). The point is in pixels, but the film is laminated the other way up from the display’s memory, so the Cap touch sketch flips both axes with map() before it draws. Leave that out and the dot appears in the opposite corner; rotate the display and the touch does not rotate with it.

Part pin

Board pin

CS

Pin 10

DC

Pin 9

RST

Pin 8

MOSI

Pin 11

SCK

Pin 13

SCL

A5

SDA

A4

LED

5 V

VCC

5 V

GND

GND

On an ESP32 DevKit the touch goes on GPIO 21 (SDA) and 22 (SCL), the pins Wire.begin() uses there; both libraries compile on every board here but the ATtiny85.

Click to open it in the editor

This is the simulator itself, running here. Click anything to open it in the editor.

Open this project in the editor Read the full tutorial

Drawing where the finger is, from the Cap touch sketch

How it is modeled

## What is true about the Touch TFT, 2.8 inch ILI9341 with FT6206, here

In its help article’s own words: what the simulation gets right, and where it stops.

### Modeled

The display is the ILI9341 model. The touch controller answers FocalTech's
registers: the vendor and chip IDs the library checks, the touch count, and the
point in pixels with its press, contact and lift flags, all read in one go. The
point is the other way up from the display's memory, as on the real module, which
is why every example turns it round.

### Not modeled

A second finger, gestures, the threshold's effect, and the controller's interrupt
and reset lines, which this board does not bring out.

From Touch TFT, 2.8 inch with capacitive touch, in full.

Projects

## See the Touch TFT, 2.8 inch ILI9341 with FT6206 in a project

One built-in project uses it. It opens in the editor, already wired.

Boards

## The boards it is shown on

This board has a built-in project with the Touch TFT, 2.8 inch ILI9341 with FT6206 in it.

- Arduino Uno R3

Libraries

## Arduino libraries for the Touch TFT, 2.8 inch ILI9341 with FT6206

Built in, so the sketch compiles with nothing to install. Each page has the calls, the wiring and an example to run.

- Adafruit FT6206 Library

More parts

## The rest of the bench

Every one of these is drawn and simulated the same way.

Full-size breadboard

A real 0.1 inch grid with the rails and the center channel, 63 columns wide.

Jumper wires

Drag from any pin or hole to any other. Corners snap, and you can drag them.

Power

A supply rail at the voltage you choose.

Ground

The other end of every circuit.

LED

Lights when current flows. Five colors, and the brightness is what your eye would see.

Filament lamp

A tungsten bulb in a holder: an inrush when it is switched on cold, tens of milliseconds to warm up, and dim on half its voltage.

Resistor

Any value you like, with the color bands drawn to match.

ESP32-C3-DevKitM-1

A RISC-V board that runs your firmware at 160 MHz on the real memory map.

Pushbutton

A 12 mm tactile switch. Hold it while the simulation runs.

Raspberry Pi Pico

The RP2040 board on our own Cortex-M0+ core. Pick a program and press Run.

Raspberry Pi Pico W

Raspberry Pi Pico W (RP2040). The same board and the same pinout as a Pico, with the CYW43439 on it. The WiFi is simulated (no radio; real internet through the Cloud panel’s switch), and the on-board LED, which hangs off that chip rather than off GP25, is driven through the same path. Everything else is the Pico.

Raspberry Pi 4 Model B

Raspberry Pi 4 Model B: the 40-pin header, driven by main.py with RPi.GPIO or gpiozero.

See every part

## Wire up the Touch TFT, 2.8 inch ILI9341 with FT6206

Open the editor and push it into the breadboard. It is free, and it runs on your own machine.

Start building free Open the editor
