Source: https://mokxi.com/parts/gsr
Updated: 2026-11-16

Part

# Galvanic skin response sensor

Two finger straps and an op-amp: sweatier skin conducts more, and the reading falls.

See every part

- 3 pins
- In 1 project

Drawn live by the editor's own code, at the size you see it.

At a glance

## The Galvanic skin response sensor in brief

What it is, and where it sits on the bench.

The galvanic skin response sensor is the Grove GSR module: two finger straps on a lead and a small board that turns your skin’s conductance into a voltage. Skin conducts more when it sweats, even slightly, and the board puts a small voltage across the straps and an op-amp turns the current into SIG. The pins are GND, VCC, 3.3 V to 5 V, and SIG, ratiometric to VCC: half the supply with no fingers on the straps and lower as the skin conducts more. The reading follows the module’s published formula R = (1024 + 2x) x 10 k / (512 - x), so open straps read 512 on a 5 V Arduino. A slider sets the conductance in microsiemens. It is not a lie detector, and nothing is.

Family

Sensors

Pins

3

Pins

## 3 pins

Named as the editor names them, so a wire lands where you expect it.

Pin

Role

What it does

GND

Input or output

Ground.

VCC

Input or output

Supply, 3.3 V to 5 V.

SIG

Output

The reading, ratiometric to VCC: half the supply with no fingers on the straps, lower as the skin conducts more.

How to use it

## How to read a GSR skin response sensor with an Arduino

The module has three wires: VCC to the Uno’s IOREF, which is its 5 V, GND to ground and SIG to A0. Skin conducts more when it sweats, and the module reads lower as it does, so open straps read 512 and a calmer finger reads higher than a sweaty one. The sketch turns the reading into microsiemens with the module’s own formula: ohms = (1024 + 2x) x 10 k / (512 - x), then 1 000 000 divided by ohms.

This is a science fair demo of the stress response, not a lie detector. Skin conductance and heart rate rise with surprise, effort and laughter as readily as with a fib. The sketch learns a calm baseline for 10 seconds when you press the calibrate button on A3, adds a MAX30102 heart rate, and shows how far the body has moved from baseline on a ten segment LED bar on pins 2 to 11. Drag the GSR slider up to see it.

Part pin

Board pin

VCC

IOREF (the Uno’s 5 V)

GND

GND

SIG

A0

Hold the button

This is the simulator itself, running here. Click anything to open it in the editor.

Open this project in the editor Read the full tutorial

The reading in microsiemens

Common errors

## Common Galvanic skin response sensor errors and fixes

What goes wrong

The fix

More sweat gives a smaller number.

The module reads lower as the skin conducts more. Turn it around in the sketch, or convert to microsiemens and compare against a baseline.

The reading is stuck at 512.

That is open straps, nothing between them. Put a finger on both straps, or set the slider above 0.

SIG is not driven.

Below 3 V the module is not running. Give it 3.3 V to 5 V on VCC.

Questions

## Questions and answers

### Is a GSR sensor a lie detector?

No. Skin conductance rises with surprise, effort, laughter and a cold room as readily as with a fib. It is a good sensor for a science fair on the body’s stress response.

### What is the GSR reading with open straps?

512 on a 5 V Arduino, half the supply.

### What is a normal skin conductance?

The model’s calm, dry fingers sit around 2 microsiemens, and a startle lifts that by a few. Real skin responds slowly, over seconds.

How it is modeled

## What is true about the Galvanic skin response sensor, here

In its help article’s own words: what the simulation gets right, and where it stops.

### Modeled

The reading follows the module's own published formula,
R = (1024 + 2x) * 10 k / (512 - x), run backwards from the conductance you set, so
the same sketch that converts a reading to ohms on a real module gets your number back
here. Open straps read 512 on a 5 V Arduino. Below 3 V the module is not running and
SIG is not driven.

### Not modeled

How slowly real skin responds (a peak rises over one to three seconds and fades over
ten), temperature, the trim pot (the model assumes it is set the way the module's
instructions say, with open straps at 512), and the electrodes' own drift.

It is also not a lie detector, and nothing is. Skin conductance rises with surprise,
effort, laughter and a cold room as readily as with a fib. It is a lovely sensor for a
science fair about the body's stress response, which is exactly how to present it.

From Galvanic skin response sensor, in full.

Projects

## See the Galvanic skin response sensor in a project

One built-in project uses it. It opens in the editor, already wired.

Boards

## The boards it is shown on

This board has a built-in project with the Galvanic skin response sensor in it.

- Arduino Uno R3

Keep going

## Keep going

- Arduino Pulse Sensor: Heart Rate on an OLED
- Analog vs Digital Pins, and ADC Resolution
- MAX30102 pulse oximeter
- LED bar graph, 10 segments

More parts

## The rest of the bench

Every one of these is drawn and simulated the same way.

Full-size breadboard

A real 0.1 inch grid with the rails and the center channel, 63 columns wide.

Jumper wires

Drag from any pin or hole to any other. Corners snap, and you can drag them.

Power

A supply rail at the voltage you choose.

Ground

The other end of every circuit.

LED

Lights when current flows. Five colors, and the brightness is what your eye would see.

Filament lamp

A tungsten bulb in a holder: an inrush when it is switched on cold, tens of milliseconds to warm up, and dim on half its voltage.

Resistor

Any value you like, with the color bands drawn to match.

ESP32-C3-DevKitM-1

A RISC-V board that runs your firmware at 160 MHz on the real memory map.

Pushbutton

A 12 mm tactile switch. Hold it while the simulation runs.

Raspberry Pi Pico

The RP2040 board on our own Cortex-M0+ core. Pick a program and press Run.

Raspberry Pi Pico W

Raspberry Pi Pico W (RP2040). The same board and the same pinout as a Pico, with the CYW43439 on it. The WiFi is simulated (no radio; real internet through the Cloud panel’s switch), and the on-board LED, which hangs off that chip rather than off GP25, is driven through the same path. Everything else is the Pico.

Raspberry Pi 4 Model B

Raspberry Pi 4 Model B: the 40-pin header, driven by main.py with RPi.GPIO or gpiozero.

See every part

## Wire up the Galvanic skin response sensor

Open the editor and push it into the breadboard. It is free, and it runs on your own machine.

Start building free Open the editor
