Source: https://mokxi.com/parts/epaper29
Updated: 2026-11-19

Part

# E-paper display, 2.9 inch

296x128 black and white e-paper over SPI. Three seconds to refresh, and it keeps the picture with no power.

See every part

- 8 pins
- In 1 project
- In 1 lesson

Drawn live by the editor's own code, at the size you see it.

At a glance

## The E-paper display, 2.9 inch in brief

What it is, and where it sits on the bench.

The 2.9 inch e-paper display is a black and white module on the Solomon Systech SSD1680, 296 by 128 pixels, over SPI: the Waveshare 2.9 inch V2 and the WeAct 2.9 inch boards. The pins are VCC and GND, 2.2 to 3.7 V, SDA, the SPI data in, SCL, the clock, CS, active low, DC, low for a command and high for its data, RES, reset and active low, and BUSY, high while the controller works, above all during a refresh. It is the same SSD1680 model as the 2.13 inch panel, with the two RAMs, the RAM window and counters, data entry modes, reset and deep sleep. Mokxi ships GxEPD2 as GxEPD2_BW.h with the GxEPD2_290_BS, GxEPD2_290_T94 and GxEPD2_290_T94_V2 panels.

Family

Displays

Pins

8

Pins

## 8 pins

Named as the editor names them, so a wire lands where you expect it.

Pin

Role

What it does

VCC

Input or output

Supply, 2.2 to 3.7 V.

GND

Input or output

Ground.

SDA

Input

SPI data in (DIN on the Waveshare board).

SCL

Input

SPI clock (CLK).

CS

Input

Chip select, active low.

DC

Input

Low for a command, high for its data.

RES

Input

Reset, active low (RST).

BUSY

Output

High while the controller works, above all during a refresh.

How to use it

## How to use a 2.9 inch e-paper display with an Arduino and GxEPD2

The module runs on 3.3 V, so VCC goes to the Uno’s 3V3 pin, not 5 V: its supply is 2.2 to 3.7 V. SDA goes to pin 11 and SCL to pin 13, the Uno’s SPI pins, CS to 10, DC to 9, RES to 8 and BUSY to 7. A button on pin 2 marks the price down.

The GxEPD2 constructor takes CS, DC, RES and BUSY in that order. The sketch draws a label with a full window, then redraws only the price with a partial window when the button is pressed, which is faster than refreshing the whole panel. BUSY is high while the controller works, so the library waits on it. Call hibernate() when you are done to put the panel in deep sleep.

Part pin

Board pin

VCC

3V3

GND

GND

SDA, SCL

Pins 11, 13

CS, DC

Pins 10, 9

RES, BUSY

Pins 8, 7

Hold the button

This is the simulator itself, running here. Click anything to open it in the editor.

Open this project in the editor Read the full tutorial

Hello on e-paper

Common errors

## Common E-paper display, 2.9 inch errors and fixes

What goes wrong

The fix

The display is blank.

Check VCC is on 3.3 V, and CS, DC, RES and BUSY match the constructor’s order and pins. Use the panel class that matches your module.

The refresh is slow.

A full refresh takes a while and BUSY is high all the time. Use a partial window to redraw a small area.

The module is run from 5 V.

Its supply is 2.2 to 3.7 V. Use the 3.3 V pin.

Questions

## Questions and answers

### What resolution is the 2.9 inch e-paper?

296 by 128 pixels, black and white, on the SSD1680.

### What does hibernate() do on the e-paper display?

It puts the controller into deep sleep once the picture is drawn, which the model supports along with reset and the two RAMs.

### Which library does Mokxi use for e-paper?

GxEPD2, as GxEPD2_BW.h, with the GxEPD2_290_BS, GxEPD2_290_T94 and GxEPD2_290_T94_V2 panels.

How it is modeled

## What is true about the E-paper display, 2.9 inch, here

In its help article’s own words: what the simulation gets right, and where it stops.

### Modeled

It is the same SSD1680 model as the 2.13 inch panel, on 128 sources and 296 gates:
the two RAMs, the RAM window and counters, data entry modes, reset and deep sleep,
and a picture that changes only when a refresh finishes, with BUSY high while it
runs: about 3 s for a full refresh and 0.3 s for a partial one, Waveshare's typical
times. The picture stays with the power off.

### Not modeled

The flashing of a full refresh, ghosting, the temperature's effect on the refresh
time, and reading the RAM back.

From E-paper display, 2.9 inch, in full.

Projects

## See the E-paper display, 2.9 inch in a project

One built-in project uses it. It opens in the editor, already wired.

Lessons

## Where it turns up in a lesson

One lesson places it in its own circuit.

### Learn articles

1 lesson

- Arduino E-Paper Display: GxEPD2 on a 2.9 Inch Panel

Boards

## The boards it is shown on

This board has a built-in project with the E-paper display, 2.9 inch in it.

- Arduino Uno R3

Libraries

## Arduino libraries for the E-paper display, 2.9 inch

Built in, so the sketch compiles with nothing to install. Each page has the calls, the wiring and an example to run.

- GxEPD2

Keep going

## Keep going

- SPI Explained: Clock, Data and Chip Select
- Arduino OLED Display (SSD1306) Tutorial
- E-paper display, SSD1680 2.13 inch
- OLED display, 128x64
- Nokia 5110 display, PCD8544

More parts

## The rest of the bench

Every one of these is drawn and simulated the same way.

Full-size breadboard

A real 0.1 inch grid with the rails and the center channel, 63 columns wide.

Jumper wires

Drag from any pin or hole to any other. Corners snap, and you can drag them.

Power

A supply rail at the voltage you choose.

Ground

The other end of every circuit.

LED

Lights when current flows. Five colors, and the brightness is what your eye would see.

Filament lamp

A tungsten bulb in a holder: an inrush when it is switched on cold, tens of milliseconds to warm up, and dim on half its voltage.

Resistor

Any value you like, with the color bands drawn to match.

ESP32-C3-DevKitM-1

A RISC-V board that runs your firmware at 160 MHz on the real memory map.

Pushbutton

A 12 mm tactile switch. Hold it while the simulation runs.

Raspberry Pi Pico

The RP2040 board on our own Cortex-M0+ core. Pick a program and press Run.

Raspberry Pi Pico W

Raspberry Pi Pico W (RP2040). The same board and the same pinout as a Pico, with the CYW43439 on it. The WiFi is simulated (no radio; real internet through the Cloud panel’s switch), and the on-board LED, which hangs off that chip rather than off GP25, is driven through the same path. Everything else is the Pico.

Raspberry Pi 4 Model B

Raspberry Pi 4 Model B: the 40-pin header, driven by main.py with RPi.GPIO or gpiozero.

See every part

## Wire up the E-paper display, 2.9 inch

Open the editor and push it into the breadboard. It is free, and it runs on your own machine.

Start building free Open the editor
