Source: https://mokxi.com/parts/adxl335
Updated: 2026-11-19

Part

# Accelerometer, ADXL335 analog

Three analog outputs, one an axis: 1.65 V at 0 g and 330 mV a g on the GY-61’s 3.3 V.

See every part

- 5 pins
- 2 settings
- In 1 project

Drawn live by the editor's own code, at the size you see it.

At a glance

## The Accelerometer, ADXL335 analog in brief

What it is, and every setting the properties panel gives it.

The ADXL335 is the simplest accelerometer to wire: three analog outputs, one per axis, and nothing to talk to over a bus. The GY-61 board it usually comes on runs the chip from a 3.3 V regulator, so it takes 5 V from an Arduino, and its outputs are ratiometric: at zero g each sits at half the supply, 1.65 V, and one g moves it by a tenth of the supply, 330 mV. On a 5 V Uno that is about 338 counts at rest and 68 counts per g. Mokxi models a part at rest, so gravity is the only acceleration it feels: tip the board with its two sliders and the 1 g moves off Z onto X and Y, never adding up to more. Each output leaves the chip through 32 kilohms, which is what analogRead() sees. Shakes, bumps, noise and the zero-g spread between real chips are not modeled.

Family

Sensors

Pins

5

tilt_x

0

tilt_y

0

Pins

## 5 pins

Named as the editor names them, so a wire lands where you expect it.

Pin

What it does

VCC

Supply, 3 V to 5 V. The board's regulator gives the chip 3.3 V.

X

The X axis, as a voltage.

Y

The Y axis.

Z

The Z axis.

GND

Ground.

How to use it

## How to read an ADXL335 accelerometer with an Arduino

VCC to 5 V and GND to ground, then each axis to an analog input: in the tilt maze, X to A0 and Y to A1. Z is left unwired because a maze on a table only needs two axes. No library is involved: analogRead() on each pin gives the axis directly.

The arithmetic is where people slip. Zero g is not 512 on this board but about 338, half of 3.3 V read on a 5 V scale, and one g is about 68 counts either side of it. The maze treats anything more than a quarter of a g, 17 counts, as a tilt and rolls the dot one cell that way every 150 ms on the 8x8 matrix (DIN on pin 12, CLK on 11, CS on 10). Tip the board with its sliders, steer the dot to the blinking goal and the next maze appears.

Part pin

Board pin

VCC

5 V

GND

GND

X

A0

Y

A1

Z

Not wired

On a 3.3 V board the outputs span the ADC’s whole range, so zero g reads near the middle: about 2048 of 4095 on an ESP32’s ADC1 pins, which is where to wire X, Y and Z there.

Click to open it in the editor

This is the simulator itself, running here. Click anything to open it in the editor.

Open this project in the editor Read the full tutorial

A reading turned into a direction, from the tilt maze sketch

Common errors

## Common Accelerometer, ADXL335 analog errors and fixes

What goes wrong

The fix

The flat board reads as tilted.

Zero g is 1.65 V, about 338 counts on a 5 V Uno, not 512. Measure your own board flat on the table and use that as the center, since real chips vary a little.

The readings barely move with tilt.

One g is only about 68 counts on a 10-bit, 5 V ADC. Compare against a small threshold, as the maze does with 17 counts, or convert to g before deciding.

A bare ADXL335 chip stopped working on 5 V.

The chip itself is a 3.3 V part. The GY-61’s regulator is what makes 5 V safe; without one, power it from 3.3 V.

Shaking the virtual board does nothing.

The model is a part at rest that only tilts, so it measures gravity and no other motion. Test shake and tap logic on hardware.

Questions

## Questions and answers

### Does the ADXL335 need a library?

No. It has no bus: each axis is a voltage, read with analogRead(). The only work is subtracting the zero-g level and scaling by the counts per g.

### How do I turn an ADXL335 reading into an angle?

Convert each axis to g by subtracting zero g and dividing by the counts per g, then take the arcsine of one axis, or atan2 of two, for the tilt in that direction.

### Why is zero g not in the middle of the Arduino’s range?

The GY-61 runs the chip on 3.3 V and its outputs center on half of that supply. An Uno measures against 5 V, so 1.65 V lands at about a third of the scale.

### Should I use the ADXL335 or the ADXL345?

The ADXL335 is analog and needs no code beyond analogRead(); the ADXL345 is digital, over I2C or SPI, with more range settings and tap detection. Both have pages here.

How it is modeled

## What is true about the Accelerometer, ADXL335 analog, here

In its help article’s own words: what the simulation gets right, and where it stops.

### Modeled

From the ADXL335 datasheet:

Ratiometric outputs. At 0 g each output sits at half the chip's supply, and 1 g
moves it by a tenth of the supply: 300 mV/g at the datasheet's 3 V, and 330 mV/g on
the GY-61's 3.3 V. So on a 5 V Uno, 0 g is about 338 counts and 1 g about 68 counts
either side.

Gravity. The part is still, so gravity is the only acceleration: tilted, it moves
from Z onto X and Y, and the three never add up to more than 1 g.

The output resistance. Each output leaves the chip through 32 kohm, which is what
analogRead() sees.

### Not modeled

Shakes, bumps and falls; the chip-to-chip spread of the zero-g level (calibrate a
real one flat on the table); noise; and the self-test pin, which the GY-61 does not
bring out.

From Accelerometer, ADXL335, in full.

Projects

## See the Accelerometer, ADXL335 analog in a project

One built-in project uses it. It opens in the editor, already wired.

Boards

## The boards it is shown on

This board has a built-in project with the Accelerometer, ADXL335 analog in it.

- Arduino Uno R3

Keep going

## Keep going

- Arduino MPU6050: Accelerometer and Tilt
- Arduino ADXL345: Library, Example Code and Tilt
- Accelerometer, ADXL345
- Accelerometer and gyroscope, MPU6050
- Nine-axis IMU, MPU-9250

More parts

## The rest of the bench

Every one of these is drawn and simulated the same way.

Full-size breadboard

A real 0.1 inch grid with the rails and the center channel, 63 columns wide.

Jumper wires

Drag from any pin or hole to any other. Corners snap, and you can drag them.

Power

A supply rail at the voltage you choose.

Ground

The other end of every circuit.

LED

Lights when current flows. Five colors, and the brightness is what your eye would see.

Filament lamp

A tungsten bulb in a holder: an inrush when it is switched on cold, tens of milliseconds to warm up, and dim on half its voltage.

Resistor

Any value you like, with the color bands drawn to match.

ESP32-C3-DevKitM-1

A RISC-V board that runs your firmware at 160 MHz on the real memory map.

Pushbutton

A 12 mm tactile switch. Hold it while the simulation runs.

Raspberry Pi Pico

The RP2040 board on our own Cortex-M0+ core. Pick a program and press Run.

Raspberry Pi Pico W

Raspberry Pi Pico W (RP2040). The same board and the same pinout as a Pico, with the CYW43439 on it. The WiFi is simulated (no radio; real internet through the Cloud panel’s switch), and the on-board LED, which hangs off that chip rather than off GP25, is driven through the same path. Everything else is the Pico.

Raspberry Pi 4 Model B

Raspberry Pi 4 Model B: the 40-pin header, driven by main.py with RPi.GPIO or gpiozero.

See every part

## Wire up the Accelerometer, ADXL335 analog

Open the editor and push it into the breadboard. It is free, and it runs on your own machine.

Start building free Open the editor
