Source: https://mokxi.com/learn/path/sensor-signal-conditioning
Updated: 2026-11-20

All paths

# Sensor signal conditioning

Advanced, after Sensors and measurement: bridges on long cables, load cells and the HX711, thermocouples, RTDs, offset and gain, anti-alias filters, and a precision scale built two ways.

Free 7 lessons 6 h 7 chapters 2,107 XP Electrical · Advanced +250 XP

0 of 7 done

Start the course free Wheatstone bridges in practice Lesson plan for teachers

What you will build

## 0 projects, built step by step

7 lessons in 7 chapters, about 6 hours on a simulated breadboard. Free, in your browser, every step checked by the simulator.

The map

## Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

## Wheatstone bridges

Millivolts per volt, lead wires and shunt calibration.

Open 326 XP

### Wheatstone bridges in practice

A strain gauge on the end of a cable: millivolts per volt, a bridge that is not quite linear, lead wires that fake a strain, the three-wire fix, and a shunt resistor that calibrates without a weight.

0 of 7 steps

Start What is in it

4 questions, graded as you go.

Chapter 2

## Load cells

The counts behind a gram, and choosing a cell.

Locked 250 XP

### Load cells and the HX711

A load cell is a bridge in a block of aluminum, read by a 24-bit HX711: the counts behind a gram, the wrong cell for the job, why mV/V over capacity is the number that matters, and what happens past the input range.

0 of 5 steps

3 questions, graded as you go.

Chapter 3

## Thermocouples

The cold junction, the curve and a MAX31855.

Locked 326 XP

### Thermocouples

A type K thermocouple on an OP07 at 10 mV per degree: the cold junction that steals 25 degrees, compensation that tracks the room, the curve that bends at 500 C, and a MAX31855 that does it all in a chip.

0 of 7 steps

4 questions, graded as you go.

Chapter 4

## RTDs

Platinum, four wires and a MAX31865.

Locked 326 XP

### RTDs: platinum and four wires

A PT100 fed 1 mA by an LM358: 100 ohms at 0 C and 138.5 at 100 C, two lead wires that add 6.7 degrees, the four-wire measurement that ignores them, self-heating, and a MAX31865 in a chip.

0 of 7 steps

4 questions, graded as you go.

Chapter 5

## Offset and gain

Zero and span onto an ADC, and the rails that stop you.

Locked 288 XP

### Offset and gain

An LM35 mapped onto an ADC by an LM358 difference amp: gain is the span, the reference is the zero, an output that cannot go below its ground, a re-zero and a re-span, and the ceiling of a single supply.

0 of 6 steps

4 questions, graded as you go.

Chapter 6

## Anti-alias filters

Nyquist, folding and a two-pole filter before the ADC.

Locked 288 XP

### Anti-alias filters

An ADC folds anything above half its sample rate back down as a fake low tone. One RC against a two-pole Sallen-Key on an LM358: both -3 dB at 100 Hz, a tenth against a hundredth at 1 kHz, a corner moved, and the wrong capacitors.

0 of 6 steps

4 questions, graded as you go.

Chapter 7

## Boss build

A precision scale, analog and on a chip.

Locked 303 XP

### Boss build: a precision scale

A load cell read two ways: an LM358 two-op-amp in-amp at a gain of 201 into a low pass for a 10-bit ADC, and an HX711 beside it. Weigh 2.5 kg on both, trim out a cell's zero error, and re-design the analog channel for a 20 kg cell.

0 of 7 steps

3 questions, graded as you go.

Syllabus

## Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

### Wheatstone bridges

- Wheatstone bridges in practice A strain gauge on the end of a cable: millivolts per volt, a bridge that is not quite linear, lead wires that fake a strain, the three-wire fix, and a shunt resistor that calibrates without a weight.

Chapter 2

### Load cells

- Load cells and the HX711 A load cell is a bridge in a block of aluminum, read by a 24-bit HX711: the counts behind a gram, the wrong cell for the job, why mV/V over capacity is the number that matters, and what happens past the input range.

Chapter 3

### Thermocouples

- Thermocouples A type K thermocouple on an OP07 at 10 mV per degree: the cold junction that steals 25 degrees, compensation that tracks the room, the curve that bends at 500 C, and a MAX31855 that does it all in a chip.

Chapter 4

### RTDs

- RTDs: platinum and four wires A PT100 fed 1 mA by an LM358: 100 ohms at 0 C and 138.5 at 100 C, two lead wires that add 6.7 degrees, the four-wire measurement that ignores them, self-heating, and a MAX31865 in a chip.

Chapter 5

### Offset and gain

- Offset and gain An LM35 mapped onto an ADC by an LM358 difference amp: gain is the span, the reference is the zero, an output that cannot go below its ground, a re-zero and a re-span, and the ceiling of a single supply.

Chapter 6

### Anti-alias filters

- Anti-alias filters An ADC folds anything above half its sample rate back down as a fake low tone. One RC against a two-pole Sallen-Key on an LM358: both -3 dB at 100 Hz, a tenth against a hundredth at 1 kHz, a corner moved, and the wrong capacitors.

Chapter 7

### Boss build

- Boss build: a precision scale A load cell read two ways: an LM358 two-op-amp in-amp at a gain of 201 into a low pass for a 10-bit ADC, and an HX711 beside it. Weigh 2.5 kg on both, trim out a cell's zero error, and re-design the analog channel for a 20 kg cell.

Kits

## Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

### Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kit

Questions

## About Sensor signal conditioning

Is Sensor signal conditioning free?

Yes. All 7 lessons of Sensor signal conditioning are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need any parts?

No. Every circuit is built on a simulated breadboard, and the simulator checks each step as you go. When you want to build it for real, the same parts and wiring work on a real bench.

How long does Sensor signal conditioning take?

About 6 hours: 7 lessons in 7 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

Where do I start?

With "Wheatstone bridges in practice", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.
