Source: https://mokxi.com/learn/path/python-hardware-playground
Updated: 2026-11-20

All paths

# Python on the Pi's pins

Drive real parts from Python with gpiozero: LEDs and PWM, buttons and events, buzzer signals and tunes, servos, a sonar and a motion sensor, then build a desk alarm as a state machine.

Raspberry Pi 4 Model B Free 7 lessons 5 h 3 chapters 1,445 XP Coding · Beginner +100 XP

0 of 7 done

Start the course free LEDs and PWM Lesson plan for teachers

What you will build

## 2 projects, built step by step

7 lessons in 3 chapters, about 5 hours on a simulated Raspberry Pi 4 Model B. Free, in your browser, every step checked by the simulator.

Chapter 1 project

### Buzzers and tunes

Make ship alarms with gpiozero: a Buzzer on and off, beep() in the background, Morse code sent from a dict, the math that turns note names into frequencies, and a rising tune on a TonalBuzzer, with the circuit's LED standing in for the buzzer so you can see every signal.
Open it in the simulator

Chapter 2 project

### Motion sensor

Watch an airlock with a PIR sensor: wait for motion and stillness, switch to when_motion events so the program is free, log every visit with a time, and add a cooldown so one person does not raise ten alerts.
Open it in the simulator

The map

## Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

## Outputs

Pins high and low, PWM, and signals you can see and hear.

Open 190 XP

### LEDs and PWM

Drive the launch pad lights with gpiozero: on and off, a countdown that blinks, blink() running in the background, PWM for brightness, the duty cycle worked out in milliseconds, and pulse() for a breathing engine glow.

0 of 6 steps

Start What is in it

Locked 165 XP

### Buttons and events

Read a pushbutton three ways: polling is_pressed in a loop, counting presses by watching for the change, and letting gpiozero call your functions with when_pressed and when_held; then build a reaction timer.

0 of 5 steps

Project Locked 330 XP

### Buzzers and tunes

Make ship alarms with gpiozero: a Buzzer on and off, beep() in the background, Morse code sent from a dict, the math that turns note names into frequencies, and a rising tune on a TonalBuzzer, with the circuit's LED standing in for the buzzer so you can see every signal.

0 of 5 steps

4 questions, graded as you go.

Chapter 2

## Motion and sensing

Pulses that set an angle, echoes that measure, and heat that moves.

Locked 140 XP

### Servos

Aim an antenna dish with a hobby servo: Servo min and max, why its default pulses miss this servo's range, AngularServo with the right pulse widths, angles typed in the Serial Monitor and checked first, and a sweep that ends with detach().

0 of 4 steps

Locked 165 XP

### Distance sensor

Build a sonar with an HC-SR04 and gpiozero's DistanceSensor: read the distance, move the target and see it change, light a warning when something comes within 20 cm, draw a bar graph that grows as it nears, and work out the echo times from the speed of sound, in air and under the sea.

0 of 5 steps

Project Locked 280 XP

### Motion sensor

Watch an airlock with a PIR sensor: wait for motion and stillness, switch to when_motion events so the program is free, log every visit with a time, and add a cooldown so one person does not raise ten alerts.

0 of 4 steps

4 questions, graded as you go.

Chapter 3

## Project

Sensing, timing and state in one build: the desk alarm.

Locked 175 XP

### Project: a desk alarm

The finale: a drawer alarm as a state machine. Arm it from the Serial Monitor, let the drawer switch trigger an entry delay, sound a flashing siren when time runs out, stand it down with a secret knock on the same switch, and keep a timed log of what happened.

0 of 6 steps

3 questions, graded as you go.

Syllabus

## Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

### Outputs

- LEDs and PWM Drive the launch pad lights with gpiozero: on and off, a countdown that blinks, blink() running in the background, PWM for brightness, the duty cycle worked out in milliseconds, and pulse() for a breathing engine glow.
- Buttons and events Read a pushbutton three ways: polling is_pressed in a loop, counting presses by watching for the change, and letting gpiozero call your functions with when_pressed and when_held; then build a reaction timer.
- Buzzers and tunes Make ship alarms with gpiozero: a Buzzer on and off, beep() in the background, Morse code sent from a dict, the math that turns note names into frequencies, and a rising tune on a TonalBuzzer, with the circuit's LED standing in for the buzzer so you can see every signal.

Chapter 2

### Motion and sensing

- Servos Aim an antenna dish with a hobby servo: Servo min and max, why its default pulses miss this servo's range, AngularServo with the right pulse widths, angles typed in the Serial Monitor and checked first, and a sweep that ends with detach().
- Distance sensor Build a sonar with an HC-SR04 and gpiozero's DistanceSensor: read the distance, move the target and see it change, light a warning when something comes within 20 cm, draw a bar graph that grows as it nears, and work out the echo times from the speed of sound, in air and under the sea.
- Motion sensor Watch an airlock with a PIR sensor: wait for motion and stillness, switch to when_motion events so the program is free, log every visit with a time, and add a cooldown so one person does not raise ten alerts.

Chapter 3

### Project

- Project: a desk alarm The finale: a drawer alarm as a state machine. Arm it from the Serial Monitor, let the drawer switch trigger an entry delay, sound a flashing siren when time runs out, stand it down with a secret knock on the same switch, and keep a timed log of what happened.

Kits

## Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

### Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kit

Questions

## About Python on the Pi's pins

Is Python on the Pi's pins free?

Yes. All 7 lessons of Python on the Pi's pins are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need a real Raspberry Pi 4 Model B?

No. Every lesson runs on a simulated Raspberry Pi 4 Model B with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.

How long does Python on the Pi's pins take?

About 5 hours: 7 lessons in 3 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

What will I build?

Each chapter ends in a project that puts it together: Buzzers and tunes and Motion sensor.

Where do I start?

With "LEDs and PWM", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.
