Source: https://mokxi.com/learn/path/protection-circuits
Updated: 2026-11-20

All paths

# Protection circuits

Keep a mistake from killing your electronics: fuses and resettable limits, reverse polarity, surge clamps, inrush limiting, flyback clamps, crowbars, and a power input you harden against all of it.

Free 7 lessons 5 h 7 chapters 1,417 XP Electrical · Intermediate +150 XP

0 of 7 done

Start the course free Fuses and resettable limits Lesson plan for teachers

What you will build

## 0 projects, built step by step

7 lessons in 7 chapters, about 5 hours on a simulated breadboard. Free, in your browser, every step checked by the simulator.

The map

## Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

## Fuses and PTCs

One-shot fuses against resettable limits.

Open 205 XP

### Fuses and resettable limits

A one-shot fuse against a resettable limit: a 2 A fuse that opens on a short and stays open, a current limit that holds a short at a safe current, the rail it collapses, and the recovery a PTC or eFuse gives you.

0 of 5 steps

Start What is in it

3 questions, graded as you go.

Chapter 2

## Reverse polarity

A series diode and a P-MOSFET.

Locked 205 XP

### Reverse polarity

Two ways to survive a battery put in backward: a series Schottky diode and what it costs in volts, and a P-channel MOSFET that does the same with almost no loss, blocking either way around.

0 of 5 steps

3 questions, graded as you go.

Chapter 3

## TVS and ESD

Clamp a surge, and what ESD needs.

Locked 218 XP

### TVS and ESD

A surge on a supply line burns out an unprotected lamp; a clamp diode across the rail holds it at a safe voltage and takes the current instead; and what ESD is, and why it needs a faster part than the simulator models.

0 of 6 steps

3 questions, graded as you go.

Chapter 4

## Inrush limiting

A limiter, its cost, and the bypass.

Locked 205 XP

### Inrush limiting

A big input capacitor that blows the fuse at switch-on, a limiter resistor (an NTC's cold resistance) that stops it, the power the limiter wastes once running, and the bypass that takes it out of the circuit.

0 of 5 steps

3 questions, graded as you go.

Chapter 5

## Flyback diodes

A diode clamp and a diode-Zener clamp.

Locked 174 XP

### Flyback clamps

The coil kick from the magnetism course, clamped two ways: a plain flyback diode that holds the drain one drop above the supply, and a diode-Zener clamp that lets it rise to a set voltage to dump the energy faster.

0 of 4 steps

3 questions, graded as you go.

Chapter 6

## Crowbars

Sense, short, and let the fuse clear it.

Locked 205 XP

### Crowbars

An overvoltage crowbar: a Zener that senses the rail, a switch that shorts it, and the fuse that clears the fault, then the same crowbar on a current-limited supply, and how the trip point is chosen.

0 of 5 steps

3 questions, graded as you go.

Chapter 7

## Boss build

A bulletproof 12 V input.

Locked 205 XP

### Boss: a bulletproof power input

One 12 V input hardened against everything in the course: a fuse, a P-MOSFET for reverse polarity and a clamp for surges in front of a lamp, then test it backward, surged and shorted, and retune the clamp for 16 V parts.

0 of 5 steps

3 questions, graded as you go.

Syllabus

## Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

### Fuses and PTCs

- Fuses and resettable limits A one-shot fuse against a resettable limit: a 2 A fuse that opens on a short and stays open, a current limit that holds a short at a safe current, the rail it collapses, and the recovery a PTC or eFuse gives you.

Chapter 2

### Reverse polarity

- Reverse polarity Two ways to survive a battery put in backward: a series Schottky diode and what it costs in volts, and a P-channel MOSFET that does the same with almost no loss, blocking either way around.

Chapter 3

### TVS and ESD

- TVS and ESD A surge on a supply line burns out an unprotected lamp; a clamp diode across the rail holds it at a safe voltage and takes the current instead; and what ESD is, and why it needs a faster part than the simulator models.

Chapter 4

### Inrush limiting

- Inrush limiting A big input capacitor that blows the fuse at switch-on, a limiter resistor (an NTC's cold resistance) that stops it, the power the limiter wastes once running, and the bypass that takes it out of the circuit.

Chapter 5

### Flyback diodes

- Flyback clamps The coil kick from the magnetism course, clamped two ways: a plain flyback diode that holds the drain one drop above the supply, and a diode-Zener clamp that lets it rise to a set voltage to dump the energy faster.

Chapter 6

### Crowbars

- Crowbars An overvoltage crowbar: a Zener that senses the rail, a switch that shorts it, and the fuse that clears the fault, then the same crowbar on a current-limited supply, and how the trip point is chosen.

Chapter 7

### Boss build

- Boss: a bulletproof power input One 12 V input hardened against everything in the course: a fuse, a P-MOSFET for reverse polarity and a clamp for surges in front of a lamp, then test it backward, surged and shorted, and retune the clamp for 16 V parts.

Kits

## Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

### Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kit

Questions

## About Protection circuits

Is Protection circuits free?

Yes. All 7 lessons of Protection circuits are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need any parts?

No. Every circuit is built on a simulated breadboard, and the simulator checks each step as you go. When you want to build it for real, the same parts and wiring work on a real bench.

How long does Protection circuits take?

About 5 hours: 7 lessons in 7 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

Where do I start?

With "Fuses and resettable limits", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.
