Source: https://mokxi.com/learn/path/printer-cnc-basics
Updated: 2026-11-20

All paths

# 3D printer and CNC basics

Learn what a printer’s firmware does underneath: homing, temperature control with safety, G-code motion and runout detection.

Arduino Uno R3 Free 4 lessons 4 h 2 chapters 1,111 XP Maker · Advanced +250 XP

0 of 4 done

Start the course free Stepper homing Lesson plan for teachers

What you will build

## 2 projects, built step by step

4 lessons in 2 chapters, about 4 hours on a simulated Arduino Uno R3. Free, in your browser, every step checked by the simulator.

Chapter 1 project

### A mini G-code interpreter

Send G28, G0, G1 and M114 to a two-axis plotter line by line, and see what a firmware does with each one: home, interpolate, report, answer ok.
Open it in the simulator

Chapter 2 project

### A filament runout sensor

An optical runout sensor, a debounce, the filament still in the path after the sensor, and a pause that waits for new filament and a press of resume.
Open it in the simulator

The map

## Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

## Motion

Find zero with an endstop, then move two axes from G-code lines.

Open 189 XP

### Stepper homing

How a printer finds zero: an A4988, a NEMA 17 and an endstop, a fast seek, a back-off and a slow second touch, then moves inside software limits.

0 of 4 steps

Start What is in it

Project Locked 378 XP

### A mini G-code interpreter

Send G28, G0, G1 and M114 to a two-axis plotter line by line, and see what a firmware does with each one: home, interpolate, report, answer ok.

0 of 4 steps

Chapter 2

## Printing safely

Hold a heater at temperature, catch a loose sensor and pause for empty spools.

Locked 166 XP

### Heated bed PID and thermal runaway

A thermistor, a MOSFET and a PID loop that hold a bed at temperature, and the protection that switches the heater off when the reading stops following it.

0 of 4 steps

Project Locked 378 XP

### A filament runout sensor

An optical runout sensor, a debounce, the filament still in the path after the sensor, and a pause that waits for new filament and a press of resume.

0 of 4 steps

Syllabus

## Every lesson in the course

All 4 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

### Motion

- Stepper homing How a printer finds zero: an A4988, a NEMA 17 and an endstop, a fast seek, a back-off and a slow second touch, then moves inside software limits.
- A mini G-code interpreter Send G28, G0, G1 and M114 to a two-axis plotter line by line, and see what a firmware does with each one: home, interpolate, report, answer ok.

Chapter 2

### Printing safely

- Heated bed PID and thermal runaway A thermistor, a MOSFET and a PID loop that hold a bed at temperature, and the protection that switches the heater off when the reading stops following it.
- A filament runout sensor An optical runout sensor, a debounce, the filament still in the path after the sensor, and a pause that waits for new filament and a press of resume.

Keep going

## The next course on your track

3D printer and CNC basics is part of the robotics track, a ladder of courses from zero to expert.

Next course

### PLCs and ladder logic

How factory machines think: the scan cycle, contacts and coils, seal-in circuits, timers, counters and sequencers, ending on a crossing controller you design rung by rung.
Open the next course

Track

### Robotics track

Motors, servos, sensors and PID control loops, then a rover, a claw machine and a balance bot, every lesson checked on a simulated board.
See every course on the track

Kits

## Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

### Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kit

Questions

## About 3D printer and CNC basics

Is 3D printer and CNC basics free?

Yes. All 4 lessons of 3D printer and CNC basics are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need a real Arduino Uno R3?

No. Every lesson runs on a simulated Arduino Uno R3 with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.

How long does 3D printer and CNC basics take?

About 4 hours: 4 lessons in 2 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

What will I build?

Each chapter ends in a project that puts it together: A mini G-code interpreter and A filament runout sensor.

Where do I start?

With "Stepper homing", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.
