Source: https://mokxi.com/learn/path/pi-hardware-python
Updated: 2026-11-20

All paths

# Pi hardware in Python: I2C, SPI and PWM

The Raspberry Pi’s hardware from Python: gpiozero beyond blinking, I2C sensors with smbus2, an SPI ADC with spidev, a servo gauge needle, your own OLED driver and callbacks, ending in a Pi weather terminal.

Raspberry Pi 4 Model B Free 7 lessons 6 h 4 chapters 2,446 XP Embedded engineering · Intermediate +150 XP

0 of 7 done

Start the course free gpiozero beyond basics Lesson plan for teachers

What you will build

## 3 projects, built step by step

7 lessons in 4 chapters, about 6 hours on a simulated Raspberry Pi 4 Model B. Free, in your browser, every step checked by the simulator.

Chapter 1 project

### smbus2 sensors

Talk to an I2C chip yourself: scan the bus as i2cdetect does, read one register and a block of them from a BME280, let a driver do the datasheet’s math, and read the error when nobody answers.
Open it in the simulator

Chapter 2 project

### PWM servos: a gauge needle

A servo as a barometer’s needle: a 50 Hz pulse from 1 ms to 2 ms sets its angle, a duty cycle from 5 to 10 percent with RPi.GPIO PWM, and air pressure mapped onto 180 degrees.
Open it in the simulator

Chapter 3 project

### Callbacks

Let the button call your code: when_pressed, when_released and when_held with hold_time, a counter shared with the callbacks, and a main loop that stays free the whole time.
Open it in the simulator

The map

## Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

## Devices and I2C

gpiozero’s devices, and a sensor register by register.

Open 249 XP

### gpiozero beyond basics

Devices with a value, not just on and off: PWMLED brightness, blink a set number of times, a pulse that runs in the background, and devices wired to each other with source.

0 of 7 steps

Start What is in it

Project Locked 498 XP

### smbus2 sensors

Talk to an I2C chip yourself: scan the bus as i2cdetect does, read one register and a block of them from a BME280, let a driver do the datasheet’s math, and read the error when nobody answers.

0 of 7 steps

4 questions, graded as you go.

Chapter 2

## SPI and PWM

An ADC over SPI, and a servo needle on PWM.

Locked 187 XP

### spidev ADC

The Pi has no analog inputs, so an MCP3008 converts for it over SPI. Send the three bytes yourself with spidev and decode the 10-bit answer, then let gpiozero’s MCP3008 do the same in one line.

0 of 5 steps

Project Locked 498 XP

### PWM servos: a gauge needle

A servo as a barometer’s needle: a 50 Hz pulse from 1 ms to 2 ms sets its angle, a duty cycle from 5 to 10 percent with RPi.GPIO PWM, and air pressure mapped onto 180 degrees.

0 of 7 steps

4 questions, graded as you go.

Chapter 3

## Drivers and events

Your own OLED driver, and code the hardware calls.

Locked 218 XP

### An OLED driver in Python

Write the driver yourself: the SSD1306’s setup commands, a 1024-byte framebuffer where each byte is eight stacked pixels, pixel() with bit arithmetic, and show() in 16-byte I2C writes. Then a bar graph of the knob.

0 of 6 steps

Project Locked 498 XP

### Callbacks

Let the button call your code: when_pressed, when_released and when_held with hold_time, a counter shared with the callbacks, and a main loop that stays free the whole time.

0 of 7 steps

4 questions, graded as you go.

Chapter 4

## Boss project

A Pi weather terminal from the whole bench.

Locked 298 XP

### Boss: a Pi weather terminal

The whole bench as one device: BME280 readings on the OLED, a knob that turns the pages, a servo pressure needle, a damp-air light, and a button that logs readings to a CSV file.

0 of 8 steps

3 questions, graded as you go.

Syllabus

## Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

### Devices and I2C

- gpiozero beyond basics Devices with a value, not just on and off: PWMLED brightness, blink a set number of times, a pulse that runs in the background, and devices wired to each other with source.
- smbus2 sensors Talk to an I2C chip yourself: scan the bus as i2cdetect does, read one register and a block of them from a BME280, let a driver do the datasheet’s math, and read the error when nobody answers.

Chapter 2

### SPI and PWM

- spidev ADC The Pi has no analog inputs, so an MCP3008 converts for it over SPI. Send the three bytes yourself with spidev and decode the 10-bit answer, then let gpiozero’s MCP3008 do the same in one line.
- PWM servos: a gauge needle A servo as a barometer’s needle: a 50 Hz pulse from 1 ms to 2 ms sets its angle, a duty cycle from 5 to 10 percent with RPi.GPIO PWM, and air pressure mapped onto 180 degrees.

Chapter 3

### Drivers and events

- An OLED driver in Python Write the driver yourself: the SSD1306’s setup commands, a 1024-byte framebuffer where each byte is eight stacked pixels, pixel() with bit arithmetic, and show() in 16-byte I2C writes. Then a bar graph of the knob.
- Callbacks Let the button call your code: when_pressed, when_released and when_held with hold_time, a counter shared with the callbacks, and a main loop that stays free the whole time.

Chapter 4

### Boss project

- Boss: a Pi weather terminal The whole bench as one device: BME280 readings on the OLED, a knob that turns the pages, a servo pressure needle, a damp-air light, and a button that logs readings to a CSV file.

Kits

## Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

### Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kit

Questions

## About Pi hardware in Python: I2C, SPI and PWM

Is Pi hardware in Python: I2C, SPI and PWM free?

Yes. All 7 lessons of Pi hardware in Python: I2C, SPI and PWM are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need a real Raspberry Pi 4 Model B?

No. Every lesson runs on a simulated Raspberry Pi 4 Model B with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.

How long does Pi hardware in Python: I2C, SPI and PWM take?

About 6 hours: 7 lessons in 4 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

What will I build?

Each chapter ends in a project that puts it together: smbus2 sensors, PWM servos: a gauge needle and Callbacks.

Where do I start?

With "gpiozero beyond basics", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.
