Source: https://mokxi.com/learn/path/linear-power-supplies
Updated: 2026-11-20

All paths

# Linear power supplies

From a transformer's AC to clean DC: bridge rectifiers and ripple, Zener regulators, the LM317, low-dropout regulators, heat and heatsinks, and a dual bench supply you design down to every part.

Free 7 lessons 5 h 7 chapters 1,448 XP Electrical · Intermediate +150 XP

0 of 7 done

Start the course free Transformer to DC Lesson plan for teachers

What you will build

## 0 projects, built step by step

7 lessons in 7 chapters, about 5 hours on a simulated breadboard. Free, in your browser, every step checked by the simulator.

The map

## Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

## Transformer to DC

A secondary, a bridge and a smoothing capacitor.

Open 205 XP

### Transformer to DC

From the wall to a DC rail: a transformer's 12 V secondary, a bridge rectifier that flips every half cycle the same way, the two diode drops it costs, and the smoothing capacitor that turns humps into a rail.

0 of 5 steps

Start What is in it

3 questions, graded as you go.

Chapter 2

## Ripple

I / (2 f C), on an AC range and a scope.

Locked 205 XP

### Ripple

The sawtooth a reservoir capacitor leaves on the rail: reading it on an AC range, the I / (2 f C) rule, a bigger capacitor, a heavier load, and why the lowest point of the ripple is the number that matters.

0 of 5 steps

3 questions, graded as you go.

Chapter 3

## Zener regulators

A resistor, a Zener, and the load they can carry.

Locked 205 XP

### Zener regulators

The simplest regulator: a resistor and a Zener on the raw rail, how well it holds 5 V as the load changes, the current it wastes, and the load it cannot carry.

0 of 5 steps

3 questions, graded as you go.

Chapter 4

## LM317

Two resistors set the voltage; headroom keeps it.

Locked 205 XP

### The LM317

An adjustable regulator from three legs and two resistors: 5 V from 240 and 720 ohms, a new voltage from a new resistor, how little ripple gets through, and the headroom it needs.

0 of 5 steps

3 questions, graded as you go.

Chapter 5

## LDO dropout

How low the input can go.

Locked 205 XP

### LDO dropout

How close to its output a regulator's input can fall: a 7805 that gives up 2 V short, an AMS1117 that needs 1.1 V, and an MCP1700 that runs a 3.3 V board from a single lithium cell to the end.

0 of 5 steps

3 questions, graded as you go.

Chapter 6

## Heatsinks

Watts, degrees per watt, and cutting the heat.

Locked 187 XP

### Heatsinks

A linear regulator turns the voltage it drops into heat: measure it, work out the junction temperature from the datasheet's degrees per watt, see what a heatsink buys, and cut the heat at the source.

0 of 5 steps

3 questions, graded as you go.

Chapter 7

## Boss build

A dual bench supply.

Locked 236 XP

### Boss: a bench supply

A small dual bench supply from the course's parts: a 24 V transformer, a bridge and a reservoir, an adjustable LM317 output, and a fixed 5 V output fed through a Zener pre-regulator. Set it, load it, check its ripple and headroom, and give it the voltage you need.

0 of 6 steps

3 questions, graded as you go.

Syllabus

## Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

### Transformer to DC

- Transformer to DC From the wall to a DC rail: a transformer's 12 V secondary, a bridge rectifier that flips every half cycle the same way, the two diode drops it costs, and the smoothing capacitor that turns humps into a rail.

Chapter 2

### Ripple

- Ripple The sawtooth a reservoir capacitor leaves on the rail: reading it on an AC range, the I / (2 f C) rule, a bigger capacitor, a heavier load, and why the lowest point of the ripple is the number that matters.

Chapter 3

### Zener regulators

- Zener regulators The simplest regulator: a resistor and a Zener on the raw rail, how well it holds 5 V as the load changes, the current it wastes, and the load it cannot carry.

Chapter 4

### LM317

- The LM317 An adjustable regulator from three legs and two resistors: 5 V from 240 and 720 ohms, a new voltage from a new resistor, how little ripple gets through, and the headroom it needs.

Chapter 5

### LDO dropout

- LDO dropout How close to its output a regulator's input can fall: a 7805 that gives up 2 V short, an AMS1117 that needs 1.1 V, and an MCP1700 that runs a 3.3 V board from a single lithium cell to the end.

Chapter 6

### Heatsinks

- Heatsinks A linear regulator turns the voltage it drops into heat: measure it, work out the junction temperature from the datasheet's degrees per watt, see what a heatsink buys, and cut the heat at the source.

Chapter 7

### Boss build

- Boss: a bench supply A small dual bench supply from the course's parts: a 24 V transformer, a bridge and a reservoir, an adjustable LM317 output, and a fixed 5 V output fed through a Zener pre-regulator. Set it, load it, check its ripple and headroom, and give it the voltage you need.

Kits

## Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

### Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kit

Questions

## About Linear power supplies

Is Linear power supplies free?

Yes. All 7 lessons of Linear power supplies are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need any parts?

No. Every circuit is built on a simulated breadboard, and the simulator checks each step as you go. When you want to build it for real, the same parts and wiring work on a real bench.

How long does Linear power supplies take?

About 5 hours: 7 lessons in 7 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

Where do I start?

With "Transformer to DC", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.
