Source: https://mokxi.com/learn/path/kit-super-starter
Updated: 2026-11-20

All paths

# Starter kit companion: the 24-lesson kit

Follows the lessons in the Elegoo Uno R3 Super Starter Kit tutorial, in its order, each one running in your browser.

Arduino Uno R3 Free 24 lessons 14 h 5 chapters 3,375 XP Maker · Beginner +100 XP

0 of 24 done

Start the course free Making the board talk Lesson plan for teachers

What you will build

## 5 projects, built step by step

24 lessons in 5 chapters, about 14 hours on a simulated Arduino Uno R3. Free, in your browser, every step checked by the simulator.

Chapter 1 project

### Kit: a button that lights an LED

Read a pushbutton with the chip’s own pull-up resistor and light an LED only while it is held.
Open it in the simulator

Chapter 2 project

### Kit: sweeping a servo

A servo turns to an angle and holds it. Send it to 0, 90 and 180 degrees, then sweep it back one degree at a time.
Open it in the simulator

Chapter 3 project

### Kit: decoding an IR remote

The receiver turns flashes of infrared into pulses, and the IRremote library turns the pulses into a button’s code.
Open it in the simulator

Chapter 4 project

### Kit: four digits by multiplexing

Four digits share their segment pins and take turns, four milliseconds each, faster than your eye can follow.
Open it in the simulator

Chapter 5 project

### Kit: a stepper on the IR remote

Put two lessons together: VOL+ and VOL- on the remote turn the stepper a quarter turn each way.
Open it in the simulator

The map

## Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

## First steps

Print, blink, light an LED, mix colors and read a button.

Open 160 XP

### Making the board talk

Printing is how you find out what a board thinks. What Serial.begin does, what a baud rate really costs, and how to print a number without lying about it.

0 of 6 steps

Start What is in it

Locked 140 XP

### Make it blink with an Uno

Two wires from an Arduino Uno to the LED you already know, then press Run and let a program do the switching. Four steps, no code to write.

0 of 4 steps

Locked 165 XP

### Build your first circuit

Start with the parts in place. Draw every wire yourself, close the loop, press Run and light the LED.

0 of 5 steps

Locked 110 XP

### Kit: mixing colors with an RGB LED

Three LEDs under one lens. Fade red, green and blue with analogWrite and watch the colors in between appear.

0 of 4 steps

Project Locked 220 XP

### Kit: a button that lights an LED

Read a pushbutton with the chip’s own pull-up resistor and light an LED only while it is held.

0 of 4 steps

Chapter 2

## Sound and motion

Two kinds of buzzer, a tilt switch and a servo.

Locked 110 XP

### Kit: an active buzzer

A buzzer with its own oscillator: power it and it sounds. The sketch only decides when.

0 of 4 steps

Locked 110 XP

### Kit: playing notes on a passive buzzer

A passive buzzer makes no sound on its own. tone() switches the pin at a note’s frequency and plays a tune.

0 of 4 steps

Locked 110 XP

### Kit: a ball tilt switch

A little ball that closes a contact while it stands up. Read it, filter its bounce, and light an LED when it tips.

0 of 4 steps

Project Locked 220 XP

### Kit: sweeping a servo

A servo turns to an angle and holds it. Send it to 0, 90 and 180 degrees, then sweep it back one degree at a time.

0 of 4 steps

Chapter 3

## Sensors and inputs

Distance, temperature, a joystick and a remote control.

Locked 110 XP

### Kit: measuring distance with sound

The HC-SR04 times an echo. Turn the time into centimeters, then beep faster as something comes closer.

0 of 4 steps

Locked 110 XP

### Kit: temperature and humidity with a DHT11

A sensor with its own little chip, read over one wire. Print the temperature and the humidity every two seconds.

0 of 4 steps

Locked 110 XP

### Kit: reading a thumb joystick

A joystick is two knobs and a button. Read both axes with analogRead and draw the position on a bar of LEDs.

0 of 4 steps

Project Locked 220 XP

### Kit: decoding an IR remote

The receiver turns flashes of infrared into pulses, and the IRremote library turns the pulses into a button’s code.

0 of 4 steps

Chapter 4

## Displays

An LCD, a shift register, the serial monitor and seven-segment digits.

Locked 110 XP

### Kit: hello on a 16x2 LCD

Wire the character display with six signal lines and the LiquidCrystal library, then count the seconds on it.

0 of 4 steps

Locked 110 XP

### Kit: a thermistor thermometer

A resistor that changes with temperature, a voltage divider, and the beta equation: degrees on the LCD.

0 of 4 steps

Locked 110 XP

### Kit: eight LEDs from three pins

The 74HC595 shift register takes a byte one bit at a time and shows all eight bits at once.

0 of 4 steps

Locked 160 XP

### Taking commands

The monitor is an input too. Read characters without blocking, act on them, and answer everything, including the things you do not understand.

0 of 6 steps

Locked 110 XP

### Kit: a photocell light meter

A resistor that changes with light, read on A0, shown as a bar of LEDs on the shift register.

0 of 4 steps

Locked 110 XP

### Kit: a countdown on a seven-segment digit

Drive a one-digit display from the 74HC595, one bit per segment, and count down from 9 to 0.

0 of 4 steps

Project Locked 220 XP

### Kit: four digits by multiplexing

Four digits share their segment pins and take turns, four milliseconds each, faster than your eye can follow.

0 of 4 steps

Chapter 5

## Motors

A DC motor both ways, a relay and a stepper, finished on the remote.

Locked 110 XP

### Kit: a DC motor both ways with the L293D

An H-bridge chip turns a motor forward, backward and off, with the speed set by PWM.

0 of 4 steps

Locked 110 XP

### Kit: switching a motor with a relay

A transistor drives the relay coil, a diode protects it, and the relay’s contacts switch a separate circuit.

0 of 4 steps

Locked 110 XP

### Kit: a stepper motor that follows a knob

A stepper turns a precise number of steps. Drive the 28BYJ-48 from its ULN2003 board and point it with a knob.

0 of 4 steps

Project Locked 220 XP

### Kit: a stepper on the IR remote

Put two lessons together: VOL+ and VOL- on the remote turn the stepper a quarter turn each way.

0 of 4 steps

Syllabus

## Every lesson in the course

All 24 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

### First steps

- Making the board talk Printing is how you find out what a board thinks. What Serial.begin does, what a baud rate really costs, and how to print a number without lying about it.
- Make it blink with an Uno Two wires from an Arduino Uno to the LED you already know, then press Run and let a program do the switching. Four steps, no code to write.
- Build your first circuit Start with the parts in place. Draw every wire yourself, close the loop, press Run and light the LED.
- Kit: mixing colors with an RGB LED Three LEDs under one lens. Fade red, green and blue with analogWrite and watch the colors in between appear.
- Kit: a button that lights an LED Read a pushbutton with the chip’s own pull-up resistor and light an LED only while it is held.

Chapter 2

### Sound and motion

- Kit: an active buzzer A buzzer with its own oscillator: power it and it sounds. The sketch only decides when.
- Kit: playing notes on a passive buzzer A passive buzzer makes no sound on its own. tone() switches the pin at a note’s frequency and plays a tune.
- Kit: a ball tilt switch A little ball that closes a contact while it stands up. Read it, filter its bounce, and light an LED when it tips.
- Kit: sweeping a servo A servo turns to an angle and holds it. Send it to 0, 90 and 180 degrees, then sweep it back one degree at a time.

Chapter 3

### Sensors and inputs

- Kit: measuring distance with sound The HC-SR04 times an echo. Turn the time into centimeters, then beep faster as something comes closer.
- Kit: temperature and humidity with a DHT11 A sensor with its own little chip, read over one wire. Print the temperature and the humidity every two seconds.
- Kit: reading a thumb joystick A joystick is two knobs and a button. Read both axes with analogRead and draw the position on a bar of LEDs.
- Kit: decoding an IR remote The receiver turns flashes of infrared into pulses, and the IRremote library turns the pulses into a button’s code.

Chapter 4

### Displays

- Kit: hello on a 16x2 LCD Wire the character display with six signal lines and the LiquidCrystal library, then count the seconds on it.
- Kit: a thermistor thermometer A resistor that changes with temperature, a voltage divider, and the beta equation: degrees on the LCD.
- Kit: eight LEDs from three pins The 74HC595 shift register takes a byte one bit at a time and shows all eight bits at once.
- Taking commands The monitor is an input too. Read characters without blocking, act on them, and answer everything, including the things you do not understand.
- Kit: a photocell light meter A resistor that changes with light, read on A0, shown as a bar of LEDs on the shift register.
- Kit: a countdown on a seven-segment digit Drive a one-digit display from the 74HC595, one bit per segment, and count down from 9 to 0.
- Kit: four digits by multiplexing Four digits share their segment pins and take turns, four milliseconds each, faster than your eye can follow.

Chapter 5

### Motors

- Kit: a DC motor both ways with the L293D An H-bridge chip turns a motor forward, backward and off, with the speed set by PWM.
- Kit: switching a motor with a relay A transistor drives the relay coil, a diode protects it, and the relay’s contacts switch a separate circuit.
- Kit: a stepper motor that follows a knob A stepper turns a precise number of steps. Drive the 28BYJ-48 from its ULN2003 board and point it with a knob.
- Kit: a stepper on the IR remote Put two lessons together: VOL+ and VOL- on the remote turn the stepper a quarter turn each way.

Keep going

## The next course on your track

Starter kit companion: the 24-lesson kit is part of the maker track, a ladder of courses from zero to expert.

Next course

### Starter kit companion: the 33-lesson kit

Follows the lessons in the Elegoo Uno R3 Most Complete Starter Kit tutorial, in its order, each one running in your browser.
Open the next course

Track

### Maker track

Follow the starter kit you already own, then build a claw machine, a balance bot, a handheld console or an LED cube, each a short course checked by the simulator.
See every course on the track

Kits

## Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Starter kit

### ELEGOO UNO R3 Super Starter Kit

6 lessons of this kit's manual are in this course.
Every lesson of the kit

Starter kit

### ELEGOO UNO R3 Most Complete Starter Kit

6 lessons of this kit's manual are in this course.
Every lesson of the kit

Starter kit

### LAFVIN Super Starter Kit

5 lessons of this kit's manual are in this course.
Every lesson of the kit

Have a kit already?

### Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kit

Questions

## About Starter kit companion: the 24-lesson kit

Is Starter kit companion: the 24-lesson kit free?

Yes. All 24 lessons of Starter kit companion: the 24-lesson kit are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need a real Arduino Uno R3?

No. Every lesson runs on a simulated Arduino Uno R3 with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.

How long does Starter kit companion: the 24-lesson kit take?

About 14 hours: 24 lessons in 5 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

What will I build?

Each chapter ends in a project that puts it together: Kit: a button that lights an LED, Kit: sweeping a servo, Kit: decoding an IR remote, Kit: four digits by multiplexing and Kit: a stepper on the IR remote.

Where do I start?

With "Making the board talk", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.
