Source: https://mokxi.com/learn/path/kit-project-book
Updated: 2026-11-20

All paths

# Starter kit companion: the project book

Follows the fifteen projects in the official Arduino Starter Kit book, in its order, each one running in your browser.

Arduino Uno R3 Free 15 lessons 10 h 4 chapters 2,145 XP Maker · Beginner +100 XP

0 of 15 done

Start the course free Build your first circuit Build it as a kit Retails for about $48, free on Mokxi. Lesson plan for teachers

What you will build

## 4 projects, built step by step

15 lessons in 4 chapters, about 10 hours on a simulated Arduino Uno R3. Free, in your browser, every step checked by the simulator.

Chapter 1 project

### Kit: a color-mixing lamp

Three light sensors behind colored gels set the red, green and blue of one LED.
Open it in the simulator

Chapter 2 project

### Kit: a tilt hourglass

Six LEDs light on a millis() timer while the sketch keeps watching a tilt switch to start again.
Open it in the simulator

Chapter 3 project

### Kit: a spinning zoetrope

The L293D H-bridge runs the motor either way, a button starts and stops it, and a knob sets the speed.
Open it in the simulator

Chapter 4 project

### Kit: pressing a button with an optocoupler

An LED and a light sensor in one chip let the board press another gadget’s button without sharing a wire.
Open it in the simulator

The map

## Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

## First lights

Wire a loop, read a button and a sensor, and mix colors.

Open 165 XP

### Build your first circuit

Start with the parts in place. Draw every wire yourself, close the loop, press Run and light the LED.

0 of 5 steps

Start What is in it

Locked 110 XP

### Kit: a starship control panel

A green lamp waits, and two red lamps flash while you hold the button. Your first if and else, and a pull-down resistor.

0 of 4 steps

Locked 110 XP

### Kit: a warm-hands meter

A TMP36 temperature sensor, three LEDs and some floating-point math: squeeze the sensor and watch the lights climb.

0 of 4 steps

Project Locked 220 XP

### Kit: a color-mixing lamp

Three light sensors behind colored gels set the red, green and blue of one LED.

0 of 4 steps

Chapter 2

## Motion and sound

Point a servo, play light as a note, and build a keyboard on one pin.

Locked 110 XP

### Kit: a mood dial

Turn a potentiometer and a servo points to match. map() turns one range of numbers into another.

0 of 4 steps

Locked 110 XP

### Kit: a light theremin

Light on a phototransistor becomes a pitch on a piezo. Wave your hand over it to play.

0 of 4 steps

Locked 110 XP

### Kit: a four-key keyboard

Four buttons share one analog pin through a ladder of resistors, and a piezo plays a note for each.

0 of 4 steps

Project Locked 220 XP

### Kit: a tilt hourglass

Six LEDs light on a millis() timer while the sketch keeps watching a tilt switch to start again.

0 of 4 steps

Chapter 3

## Motors

Switch a motor with a MOSFET, then run one both ways with an H-bridge.

Locked 110 XP

### Kit: a motor pinwheel

A MOSFET lets a pin switch a motor on a 9 V battery, and a diode catches the motor’s kick.

0 of 4 steps

Project Locked 220 XP

### Kit: a spinning zoetrope

The L293D H-bridge runs the motor either way, a button starts and stops it, and a knob sets the speed.

0 of 4 steps

Chapter 4

## Bigger builds

An answer ball, a knock lock, a touch lamp, and talking to other things.

Locked 110 XP

### Kit: an answer ball

Ask a question, tip the tilt switch, and the LCD shows an answer picked with random().

0 of 4 steps

Locked 110 XP

### Kit: a secret knock lock

Listen for a rhythm of knocks and slide a servo bolt open only for the right one.

0 of 4 steps

Locked 110 XP

### Kit: a touch lamp

A piece of foil and a 1 megohm resistor make a touch sensor, read with the CapacitiveSensor library.

0 of 4 steps

Locked 110 XP

### Kit: sending a knob to your computer

Read a potentiometer and send the number over serial, the board’s half of talking to a program on your computer.

0 of 4 steps

Project Locked 220 XP

### Kit: pressing a button with an optocoupler

An LED and a light sensor in one chip let the board press another gadget’s button without sharing a wire.

0 of 4 steps

Syllabus

## Every lesson in the course

All 15 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

### First lights

- Build your first circuit Start with the parts in place. Draw every wire yourself, close the loop, press Run and light the LED.
- Kit: a starship control panel A green lamp waits, and two red lamps flash while you hold the button. Your first if and else, and a pull-down resistor.
- Kit: a warm-hands meter A TMP36 temperature sensor, three LEDs and some floating-point math: squeeze the sensor and watch the lights climb.
- Kit: a color-mixing lamp Three light sensors behind colored gels set the red, green and blue of one LED.

Chapter 2

### Motion and sound

- Kit: a mood dial Turn a potentiometer and a servo points to match. map() turns one range of numbers into another.
- Kit: a light theremin Light on a phototransistor becomes a pitch on a piezo. Wave your hand over it to play.
- Kit: a four-key keyboard Four buttons share one analog pin through a ladder of resistors, and a piezo plays a note for each.
- Kit: a tilt hourglass Six LEDs light on a millis() timer while the sketch keeps watching a tilt switch to start again.

Chapter 3

### Motors

- Kit: a motor pinwheel A MOSFET lets a pin switch a motor on a 9 V battery, and a diode catches the motor’s kick.
- Kit: a spinning zoetrope The L293D H-bridge runs the motor either way, a button starts and stops it, and a knob sets the speed.

Chapter 4

### Bigger builds

- Kit: an answer ball Ask a question, tip the tilt switch, and the LCD shows an answer picked with random().
- Kit: a secret knock lock Listen for a rhythm of knocks and slide a servo bolt open only for the right one.
- Kit: a touch lamp A piece of foil and a 1 megohm resistor make a touch sensor, read with the CapacitiveSensor library.
- Kit: sending a knob to your computer Read a potentiometer and send the number over serial, the board’s half of talking to a program on your computer.
- Kit: pressing a button with an optocoupler An LED and a light sensor in one chip let the board press another gadget’s button without sharing a wire.

Keep going

## The next course on your track

Starter kit companion: the project book is part of the maker track, a ladder of courses from zero to expert.

Next course

### Starter kit companion: the 24-lesson kit

Follows the lessons in the Elegoo Uno R3 Super Starter Kit tutorial, in its order, each one running in your browser.
Open the next course

Track

### Maker track

Follow the starter kit you already own, then build a claw machine, a balance bot, a handheld console or an LED cube, each a short course checked by the simulator.
See every course on the track

Kits

## Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

The kit for this course

### Starter Projects Kit

The starter kit book, part one: an Uno, LEDs, light and heat sensors, a servo, a piezo and four keys.
Open the kit

Starter kit

### Arduino Starter Kit

10 lessons of this kit's manual are in this course.
Every lesson of the kit

Have a kit already?

### Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kit

Questions

## About Starter kit companion: the project book

Is Starter kit companion: the project book free?

Yes. All 15 lessons of Starter kit companion: the project book are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need a real Arduino Uno R3?

No. Every lesson runs on a simulated Arduino Uno R3 with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.

How long does Starter kit companion: the project book take?

About 10 hours: 15 lessons in 4 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

What will I build?

Each chapter ends in a project that puts it together: Kit: a color-mixing lamp, Kit: a tilt hourglass, Kit: a spinning zoetrope and Kit: pressing a button with an optocoupler.

Where do I start?

With "Build your first circuit", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.
