Source: https://mokxi.com/learn/path/interfacing-and-level-shifting
Updated: 2026-11-20

All paths

# Interfacing and level shifting

Make a 3.3 V board talk to 5 V logic and switch 12 V loads: logic thresholds, level shifters, transistor and MOSFET drivers, the ULN2803A, optocouplers and isolation, and a 12 V panel run from an ESP32-C3.

Free 7 lessons 5 h 7 chapters 1,435 XP Electrical · Intermediate +150 XP

0 of 7 done

Start the course free 3.3 V meets 5 V Lesson plan for teachers

What you will build

## 0 projects, built step by step

7 lessons in 7 chapters, about 5 hours on a simulated breadboard. Free, in your browser, every step checked by the simulator.

The map

## Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

## 3.3 V meets 5 V

Thresholds, an HCT part, a divider and a clamp diode.

Open 236 XP

### 3.3 V meets 5 V

Logic thresholds decide whether a high is a high: a 3.3 V output into 5 V CMOS, a sagging high it misses, the HCT part that accepts it, a divider for the other direction, and the clamp diode that a bare 5 V signal pushes current through.

0 of 6 steps

Start What is in it

3 questions, graded as you go.

Chapter 2

## Level shifters

The BSS138 shifter both ways, and one-way buffers.

Locked 205 XP

### Level shifters

The BSS138 bidirectional shifter on every breakout board, worked both ways round, and the one-way buffers that do the job for push-pull signals: a 74HCT125 up, a CD4050 down.

0 of 5 steps

3 questions, graded as you go.

Chapter 3

## Transistor drivers

NPN, logic-level MOSFET and a high-side P-FET.

Locked 205 XP

### Transistor drivers

A 3.3 V pin switching 12 V loads: an NPN with the right base resistor, what too big a base resistor does, a MOSFET that is not logic level against one that is, and a high-side P-MOSFET switch.

0 of 5 steps

3 questions, graded as you go.

Chapter 4

## ULN2803A

Eight sinks, a Darlington drop and built-in clamps.

Locked 205 XP

### ULN2803A

Eight Darlington sinks with their own base resistors and flyback diodes: one input on, the Darlington's saturation drop, three channels at once, a coil clamped by the chip's COM pin, and the 1.4 V input threshold.

0 of 5 steps

3 questions, graded as you go.

Chapter 5

## Optocouplers

LED current, CTR and the pull-up.

Locked 174 XP

### Optocouplers

An LED and a phototransistor in one package: the LED current a pin supplies, the output pulled low across a gap with no wire, current transfer ratio, and the pull-up that makes it saturate.

0 of 4 steps

3 questions, graded as you go.

Chapter 6

## Isolation

A 24 V field input, and grounds that disagree.

Locked 174 XP

### Isolation

A 24 V industrial input read safely by 3.3 V logic through an optocoupler: the field side's LED current, the logic side's clean low, a reverse-protection diode, and a ground difference between the two sides that changes nothing.

0 of 4 steps

3 questions, graded as you go.

Chapter 7

## Boss build

A 12 V panel with an isolated interlock.

Locked 236 XP

### Boss: a 12 V panel from 3.3 V

An ESP32-C3 runs a 12 V control panel: a transistor, a logic-level MOSFET and a ULN2803A switch lamps and a solenoid lock, and an optocoupler brings an isolated 12 V door switch back in as an interlock. Then add a channel of your own.

0 of 6 steps

3 questions, graded as you go.

Syllabus

## Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

### 3.3 V meets 5 V

- 3.3 V meets 5 V Logic thresholds decide whether a high is a high: a 3.3 V output into 5 V CMOS, a sagging high it misses, the HCT part that accepts it, a divider for the other direction, and the clamp diode that a bare 5 V signal pushes current through.

Chapter 2

### Level shifters

- Level shifters The BSS138 bidirectional shifter on every breakout board, worked both ways round, and the one-way buffers that do the job for push-pull signals: a 74HCT125 up, a CD4050 down.

Chapter 3

### Transistor drivers

- Transistor drivers A 3.3 V pin switching 12 V loads: an NPN with the right base resistor, what too big a base resistor does, a MOSFET that is not logic level against one that is, and a high-side P-MOSFET switch.

Chapter 4

### ULN2803A

- ULN2803A Eight Darlington sinks with their own base resistors and flyback diodes: one input on, the Darlington's saturation drop, three channels at once, a coil clamped by the chip's COM pin, and the 1.4 V input threshold.

Chapter 5

### Optocouplers

- Optocouplers An LED and a phototransistor in one package: the LED current a pin supplies, the output pulled low across a gap with no wire, current transfer ratio, and the pull-up that makes it saturate.

Chapter 6

### Isolation

- Isolation A 24 V industrial input read safely by 3.3 V logic through an optocoupler: the field side's LED current, the logic side's clean low, a reverse-protection diode, and a ground difference between the two sides that changes nothing.

Chapter 7

### Boss build

- Boss: a 12 V panel from 3.3 V An ESP32-C3 runs a 12 V control panel: a transistor, a logic-level MOSFET and a ULN2803A switch lamps and a solenoid lock, and an optocoupler brings an isolated 12 V door switch back in as an interlock. Then add a channel of your own.

Kits

## Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

### Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kit

Questions

## About Interfacing and level shifting

Is Interfacing and level shifting free?

Yes. All 7 lessons of Interfacing and level shifting are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need any parts?

No. Every circuit is built on a simulated breadboard, and the simulator checks each step as you go. When you want to build it for real, the same parts and wiring work on a real bench.

How long does Interfacing and level shifting take?

About 5 hours: 7 lessons in 7 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

Where do I start?

With "3.3 V meets 5 V", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.
