Source: https://mokxi.com/learn/path/home-energy-monitoring
Updated: 2026-11-20

All paths

# Measuring energy at home

How an energy monitor works: current and voltage sensing, the PZEM-004T, real power from samples, kWh and cost, and alerts, ending in a whole-house monitor. Mains stays numbers on sliders.

Free 7 lessons 6 h 7 chapters 1,404 XP Electrical · Intermediate +150 XP

0 of 7 done

Start the course free Current sensing: a shunt and a Hall sensor Lesson plan for teachers

What you will build

## 0 projects, built step by step

7 lessons in 7 chapters, about 6 hours on a simulated breadboard. Free, in your browser, every step checked by the simulator.

The map

## Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

## Current sensing

A shunt and a Hall sensor, and why a CT goes in a panel.

Open 205 XP

### Current sensing: a shunt and a Hall sensor

A 12 V load through a 0.1 ohm shunt and an ACS712: the sensor's 2.5 V zero, 185 mV an amp, the shunt's 0.1 V an amp, a predicted reading, the 20 A board's smaller step, and why a current transformer is what goes in a panel.

0 of 5 steps

Start What is in it

4 questions, graded as you go.

Chapter 2

## Voltage sensing

A ZMPT101B, RMS, a sag and a calibration.

Locked 174 XP

### Voltage sensing: a transformer and RMS

A ZMPT101B steps the mains down to a small wave on A0: the sketch finds the middle, takes the RMS and scales it, at 230 V and 120 V, through a sag, and with a trimmer that needs calibrating.

0 of 4 steps

3 questions, graded as you go.

Chapter 3

## PZEM-004T

A complete meter over Modbus, and power factor.

Locked 205 XP

### PZEM-004T: a meter in a box

An ESP32 reads a PZEM-004T over Modbus: volts, amps, power, energy, frequency and power factor, a 120 V load, what a poor power factor does to the watts, and the energy counter climbing.

0 of 5 steps

3 questions, graded as you go.

Chapter 4

## Real power from samples

EmonLib: the mean of volts times amps.

Locked 174 XP

### Real power from samples

OpenEnergyMonitor's EmonLib samples a ZMPT101B and an ACS712 in turn: RMS volts and amps, real power as the mean of volts times amps, the power factor it implies, unplugging the appliance, and watt-hours adding up.

0 of 4 steps

3 questions, graded as you go.

Chapter 5

## kWh and cost

Energy counted, priced at your rate and projected over a day.

Locked 205 XP

### kWh and cost

A whole-house monitor: the PZEM-004T's kWh, what it has cost at your rate in cents, a day's projection at the present draw, and the arithmetic every bill is built on.

0 of 5 steps

3 questions, graded as you go.

Chapter 6

## Alerts

Raise once, clear once: power and line voltage.

Locked 205 XP

### Alerts: telling someone

The monitor raises an alert once when the house passes a power limit, clears it once when it drops back, catches a low and a high line voltage, and takes your own thresholds.

0 of 5 steps

3 questions, graded as you go.

Chapter 7

## Boss build

A main and a branch, your rate and your limits.

Locked 236 XP

### Boss: a whole-house monitor

Wire the branch's current sensor, then run a monitor with a meter on the main and one on a branch: the house in watts and cents, the branch's share, your rate, your limit and a voltage alert.

0 of 6 steps

3 questions, graded as you go.

Syllabus

## Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

### Current sensing

- Current sensing: a shunt and a Hall sensor A 12 V load through a 0.1 ohm shunt and an ACS712: the sensor's 2.5 V zero, 185 mV an amp, the shunt's 0.1 V an amp, a predicted reading, the 20 A board's smaller step, and why a current transformer is what goes in a panel.

Chapter 2

### Voltage sensing

- Voltage sensing: a transformer and RMS A ZMPT101B steps the mains down to a small wave on A0: the sketch finds the middle, takes the RMS and scales it, at 230 V and 120 V, through a sag, and with a trimmer that needs calibrating.

Chapter 3

### PZEM-004T

- PZEM-004T: a meter in a box An ESP32 reads a PZEM-004T over Modbus: volts, amps, power, energy, frequency and power factor, a 120 V load, what a poor power factor does to the watts, and the energy counter climbing.

Chapter 4

### Real power from samples

- Real power from samples OpenEnergyMonitor's EmonLib samples a ZMPT101B and an ACS712 in turn: RMS volts and amps, real power as the mean of volts times amps, the power factor it implies, unplugging the appliance, and watt-hours adding up.

Chapter 5

### kWh and cost

- kWh and cost A whole-house monitor: the PZEM-004T's kWh, what it has cost at your rate in cents, a day's projection at the present draw, and the arithmetic every bill is built on.

Chapter 6

### Alerts

- Alerts: telling someone The monitor raises an alert once when the house passes a power limit, clears it once when it drops back, catches a low and a high line voltage, and takes your own thresholds.

Chapter 7

### Boss build

- Boss: a whole-house monitor Wire the branch's current sensor, then run a monitor with a meter on the main and one on a branch: the house in watts and cents, the branch's share, your rate, your limit and a voltage alert.

Kits

## Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

### Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kit

Questions

## About Measuring energy at home

Is Measuring energy at home free?

Yes. All 7 lessons of Measuring energy at home are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need any parts?

No. Every circuit is built on a simulated breadboard, and the simulator checks each step as you go. When you want to build it for real, the same parts and wiring work on a real bench.

How long does Measuring energy at home take?

About 6 hours: 7 lessons in 7 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

Where do I start?

With "Current sensing: a shunt and a Hall sensor", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.
