Source: https://mokxi.com/learn/path/fight-stick
Updated: 2026-11-20

All paths

# Build your own fight stick

One button to a full leverless controller on a Pico: SOCD, eight buttons, lit buttons, an OLED and modes.

Raspberry Pi Pico Free 5 lessons 4 h 2 chapters 1,604 XP Maker · Advanced +250 XP

0 of 5 done

Start the course free One button, read like a controller Build it as a kit Retails for about $55, free on Mokxi. Lesson plan for teachers

What you will build

## 2 projects, built step by step

5 lessons in 2 chapters, about 4 hours on a simulated Raspberry Pi Pico. Free, in your browser, every step checked by the simulator.

Chapter 1 project

### All eight attack buttons

Add the eight attack buttons in the two-row layout, keep the pins and names in one table, and report every combination at once.
Open it in the simulator

Chapter 2 project

### The full controller

Add the OLED input display, Select, Start, Home and turbo, switch SOCD and stick modes with GP2040-CE's combos, and make the template yours.
Open it in the simulator

The map

## Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

## The inputs

A button, the directions with SOCD cleaning, then all eight attacks.

Open 227 XP

### One button, read like a controller

Wire a 30 mm LED arcade button to a Pico, light its lamp, and debounce it the way controller firmware does: no added lag at all.

0 of 5 steps

Start What is in it

Locked 242 XP

### Four directions and SOCD cleaning

Wire the left-hand cluster of a leverless controller, report it in numpad notation, and clean left + right the way tournament rules ask.

0 of 6 steps

Project Locked 454 XP

### All eight attack buttons

Add the eight attack buttons in the two-row layout, keep the pins and names in one table, and report every combination at once.

0 of 5 steps

Chapter 2

## The finish

Lit buttons, a screen, mode combos and turbo: the flagship template.

Locked 227 XP

### Lit buttons with themes

Swap in LED arcade buttons, fade each lamp with PWM on its own pin, and give the controller themes that react to every press.

0 of 5 steps

Project Locked 454 XP

### The full controller

Add the OLED input display, Select, Start, Home and turbo, switch SOCD and stick modes with GP2040-CE's combos, and make the template yours.

0 of 5 steps

Syllabus

## Every lesson in the course

All 5 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

### The inputs

- One button, read like a controller Wire a 30 mm LED arcade button to a Pico, light its lamp, and debounce it the way controller firmware does: no added lag at all.
- Four directions and SOCD cleaning Wire the left-hand cluster of a leverless controller, report it in numpad notation, and clean left + right the way tournament rules ask.
- All eight attack buttons Add the eight attack buttons in the two-row layout, keep the pins and names in one table, and report every combination at once.

Chapter 2

### The finish

- Lit buttons with themes Swap in LED arcade buttons, fade each lamp with PWM on its own pin, and give the controller themes that react to every press.
- The full controller Add the OLED input display, Select, Start, Home and turbo, switch SOCD and stick modes with GP2040-CE's combos, and make the template yours.

Kits

## Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

The kit for this course

### Fight Stick Kit

A Pico, a leverless layout of arcade buttons, lit caps and a little OLED screen.
Open the kit

Have a kit already?

### Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kit

Questions

## About Build your own fight stick

Is Build your own fight stick free?

Yes. All 5 lessons of Build your own fight stick are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need a real Raspberry Pi Pico?

No. Every lesson runs on a simulated Raspberry Pi Pico with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.

How long does Build your own fight stick take?

About 4 hours: 5 lessons in 2 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

What will I build?

Each chapter ends in a project that puts it together: All eight attack buttons and The full controller.

Where do I start?

With "One button, read like a controller", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.
