Source: https://mokxi.com/learn/path/discrete-transistor-design
Updated: 2026-11-20

All paths

# Discrete transistor design

The building blocks inside every op-amp and audio amp, built from single transistors: current sources, mirrors, Darlingtons, the differential pair, push-pull stages, thermal stability, and a headphone amp of your own.

Free 7 lessons 6 h 7 chapters 1,917 XP Electrical · Advanced +250 XP

0 of 7 done

Start the course free Current sources Lesson plan for teachers

What you will build

## 0 projects, built step by step

7 lessons in 7 chapters, about 6 hours on a simulated breadboard. Free, in your browser, every step checked by the simulator.

The map

## Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

## Current sources

A transistor that holds a current, and its compliance.

Open 288 XP

### Current sources

A transistor that holds a current whatever the load: diode bias, an emitter resistor that sets the amps, compliance, supply rejection, and a 1 mA source designed from scratch.

0 of 6 steps

Start What is in it

3 questions, graded as you go.

Chapter 2

## Current mirrors

Copy a current, the Early effect, and degeneration.

Locked 288 XP

### Current mirrors

Copy a current from one transistor to another: the diode-connected reference, a mirror that follows it, the Early effect, what a mismatched pair costs, and emitter degeneration that fixes it.

0 of 6 steps

3 questions, graded as you go.

Chapter 3

## Darlington and Sziklai

Gains multiplied, and what each pair costs.

Locked 288 XP

### Darlington and Sziklai

Two transistors as one with the gains multiplied: a Darlington against a single part, its doubled base drop and high saturation, the Sziklai pair that keeps one Vbe, and a TIP120 that packs a Darlington in one case.

0 of 6 steps

3 questions, graded as you go.

Chapter 4

## Differential pair

A shared tail, gain from millivolts, common-mode rejection.

Locked 288 XP

### The differential pair

Two transistors sharing one tail current: the balanced split, small-signal gain measured in millivolts, full steering, common-mode rejection, and the input stage of every op-amp.

0 of 6 steps

3 questions, graded as you go.

Chapter 5

## Push-pull

Class B, crossover, class AB and its idle current.

Locked 250 XP

### Push-pull output stages

An NPN pushes and a PNP pulls: the dead zone of class B, crossover distortion, two diodes that bias it into class AB, its idle current, and a clean sine into a load.

0 of 5 steps

3 questions, graded as you go.

Chapter 6

## Thermal stability

Bias that survives heat, and thermal runaway.

Locked 265 XP

### Thermal stability

Why a hot transistor draws more current, fixed bias that runs away with beta, divider bias with an emitter resistor that holds steady, the Vbe drift of 2 mV per degree, and the loop behind thermal runaway.

0 of 6 steps

3 questions, graded as you go.

Chapter 7

## Boss build

A two-stage discrete headphone amplifier.

Locked 250 XP

### Boss: a discrete headphone amp

A common-emitter gain stage driving a class AB push-pull pair into a 32 ohm earpiece: check the bias, center the output, measure the gain and the power, then turn it up and find where it clips.

0 of 5 steps

3 questions, graded as you go.

Syllabus

## Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

### Current sources

- Current sources A transistor that holds a current whatever the load: diode bias, an emitter resistor that sets the amps, compliance, supply rejection, and a 1 mA source designed from scratch.

Chapter 2

### Current mirrors

- Current mirrors Copy a current from one transistor to another: the diode-connected reference, a mirror that follows it, the Early effect, what a mismatched pair costs, and emitter degeneration that fixes it.

Chapter 3

### Darlington and Sziklai

- Darlington and Sziklai Two transistors as one with the gains multiplied: a Darlington against a single part, its doubled base drop and high saturation, the Sziklai pair that keeps one Vbe, and a TIP120 that packs a Darlington in one case.

Chapter 4

### Differential pair

- The differential pair Two transistors sharing one tail current: the balanced split, small-signal gain measured in millivolts, full steering, common-mode rejection, and the input stage of every op-amp.

Chapter 5

### Push-pull

- Push-pull output stages An NPN pushes and a PNP pulls: the dead zone of class B, crossover distortion, two diodes that bias it into class AB, its idle current, and a clean sine into a load.

Chapter 6

### Thermal stability

- Thermal stability Why a hot transistor draws more current, fixed bias that runs away with beta, divider bias with an emitter resistor that holds steady, the Vbe drift of 2 mV per degree, and the loop behind thermal runaway.

Chapter 7

### Boss build

- Boss: a discrete headphone amp A common-emitter gain stage driving a class AB push-pull pair into a 32 ohm earpiece: check the bias, center the output, measure the gain and the power, then turn it up and find where it clips.

Kits

## Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

### Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kit

Questions

## About Discrete transistor design

Is Discrete transistor design free?

Yes. All 7 lessons of Discrete transistor design are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need any parts?

No. Every circuit is built on a simulated breadboard, and the simulator checks each step as you go. When you want to build it for real, the same parts and wiring work on a real bench.

How long does Discrete transistor design take?

About 6 hours: 7 lessons in 7 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

Where do I start?

With "Current sources", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.
