Source: https://mokxi.com/learn/path/build-robot-vacuum
Updated: 2026-11-20

All paths

# Build a robot vacuum

Bumpers and cliff sensors, wheel encoders and a map, random bounce against spiral against rows, a five-layer behavior ladder, and a battery that sends it home to its dock.

Arduino Uno R3 Free 7 lessons 6 h 4 chapters 2,173 XP Robotics · Advanced +250 XP

0 of 7 done

Start the course free Bump sensors Lesson plan for teachers

What you will build

## 3 projects, built step by step

7 lessons in 4 chapters, about 6 hours on a simulated Arduino Uno R3. Free, in your browser, every step checked by the simulator.

Chapter 1 project

### Cliff sensors

A TCRT5000 looking at the floor: infrared light that comes back means floor, none means a stair. Find the edge, see the cliff beat a bump, and meet the black rug every robot vacuum fears.
Open it in the simulator

Chapter 2 project

### Coverage patterns

Three ways to clean the same room and a map that scores them: random bounce, a widening spiral, and rows back and forth (boustrophedon). Measure how much each covers, and tighten the rows.
Open it in the simulator

Chapter 3 project

### Battery and docking

Read the pack through a voltage divider, decide when to head home, and drive back to the dock by dead reckoning. Then raise the threshold and see why real docks use an infrared beacon for the last bit.
Open it in the simulator

The map

## Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

## Sensing the world

Two bumpers and a cliff sensor, and the layers that decide which one wins.

Open 250 XP

### Bump sensors

The gallery’s robot vacuum: two lever microswitches on the front corners. Hit a wall on each side, watch it back up and turn away from the hit, and see why the turn is random.

0 of 5 steps

Start What is in it

Project Locked 424 XP

### Cliff sensors

A TCRT5000 looking at the floor: infrared light that comes back means floor, none means a stair. Find the edge, see the cliff beat a bump, and meet the black rug every robot vacuum fears.

0 of 4 steps

4 questions, graded as you go.

Chapter 2

## Covering a room

Encoders and dead reckoning, then three coverage patterns scored on a map.

Locked 250 XP

### Where am I? Encoders

The vacuum grown up: wheel encoders, dead reckoning and a map of a room in 10 cm squares. Drive a meter, count the edges, turn on the spot, and calibrate the wheel size.

0 of 5 steps

Project Locked 424 XP

### Coverage patterns

Three ways to clean the same room and a map that scores them: random bounce, a widening spiral, and rows back and forth (boustrophedon). Measure how much each covers, and tighten the rows.

0 of 4 steps

5 questions, graded as you go.

Chapter 3

## Behaviors and power

A five-layer behavior ladder, a battery read through a divider, and the trip home to the dock.

Locked 212 XP

### The behavior ladder

Five layers, the higher always winning: cliff, bumper, obstacle, battery, clean. Trigger each one while it cleans, and prove a cliff beats a bump.

0 of 4 steps

Project Locked 424 XP

### Battery and docking

Read the pack through a voltage divider, decide when to head home, and drive back to the dock by dead reckoning. Then raise the threshold and see why real docks use an infrared beacon for the last bit.

0 of 4 steps

4 questions, graded as you go.

Chapter 4

## Project

Clean a whole room, survive the furniture and dock.

Locked 189 XP

### Project: clean a room

Put it all together: clean the whole room in rows, with the ladder watching, deal with a chair leg and a stair on the way, then drive home and dock.

0 of 4 steps

3 questions, graded as you go.

Syllabus

## Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

### Sensing the world

- Bump sensors The gallery’s robot vacuum: two lever microswitches on the front corners. Hit a wall on each side, watch it back up and turn away from the hit, and see why the turn is random.
- Cliff sensors A TCRT5000 looking at the floor: infrared light that comes back means floor, none means a stair. Find the edge, see the cliff beat a bump, and meet the black rug every robot vacuum fears.

Chapter 2

### Covering a room

- Where am I? Encoders The vacuum grown up: wheel encoders, dead reckoning and a map of a room in 10 cm squares. Drive a meter, count the edges, turn on the spot, and calibrate the wheel size.
- Coverage patterns Three ways to clean the same room and a map that scores them: random bounce, a widening spiral, and rows back and forth (boustrophedon). Measure how much each covers, and tighten the rows.

Chapter 3

### Behaviors and power

- The behavior ladder Five layers, the higher always winning: cliff, bumper, obstacle, battery, clean. Trigger each one while it cleans, and prove a cliff beats a bump.
- Battery and docking Read the pack through a voltage divider, decide when to head home, and drive back to the dock by dead reckoning. Then raise the threshold and see why real docks use an infrared beacon for the last bit.

Chapter 4

### Project

- Project: clean a room Put it all together: clean the whole room in rows, with the ladder watching, deal with a chair leg and a stair on the way, then drive home and dock.

Keep going

## The next course on your track

Build a robot vacuum is part of the maker track, a ladder of courses from zero to expert.

Next course

### Build a smartwatch

Build a watch you could wear: a round display, an analog face in fixed-point trig, real time, steps, days of battery and a menu.
Open the next course

Track

### Maker track

Follow the starter kit you already own, then build a claw machine, a balance bot, a handheld console or an LED cube, each a short course checked by the simulator.
See every course on the track

Kits

## Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

### Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kit

Questions

## About Build a robot vacuum

Is Build a robot vacuum free?

Yes. All 7 lessons of Build a robot vacuum are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need a real Arduino Uno R3?

No. Every lesson runs on a simulated Arduino Uno R3 with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.

How long does Build a robot vacuum take?

About 6 hours: 7 lessons in 4 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

What will I build?

Each chapter ends in a project that puts it together: Cliff sensors, Coverage patterns and Battery and docking.

Where do I start?

With "Bump sensors", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.
