Source: https://mokxi.com/learn/path/build-reflow-oven
Updated: 2026-11-20

All paths

# Build a reflow oven controller

Build the low-voltage side of a reflow oven: a thermocouple, an SSR, solder profiles, PID tracking and the safety cutoffs that make it trustworthy.

Arduino Uno R3 Free 6 lessons 6 h 3 chapters 2,280 XP Maker · Advanced +250 XP

0 of 6 done

Start the course free Thermocouples Lesson plan for teachers

What you will build

## 3 projects, built step by step

6 lessons in 3 chapters, about 6 hours on a simulated Arduino Uno R3. Free, in your browser, every step checked by the simulator.

Chapter 1 project

### SSR control

Drive a solid-state relay from a pin, learn why zero-cross SSRs cannot be dimmed, and control power by switching for part of each one second window.
Open it in the simulator

Chapter 2 project

### PID tracking

Track the profile with PID and feed-forward instead of on/off, and compare the overshoot, the time above liquidus and the worst error.
Open it in the simulator

Chapter 3 project

### Project: a solder profile

The finished controller: pick a paste, track its profile with PID, watch the door and the thermocouple every pass, and finish with a summary and a beep.
Open it in the simulator

The map

## Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

## Measure and switch

A thermocouple in, a solid-state relay out.

Open 250 XP

### Thermocouples

Measure an oven with a type K thermocouple and a MAX6675: the microvolts at the tip, the cold junction they are measured against, quarter degree steps and an open probe.

0 of 5 steps

Start What is in it

Project Locked 500 XP

### SSR control

Drive a solid-state relay from a pin, learn why zero-cross SSRs cannot be dimmed, and control power by switching for part of each one second window.

0 of 5 steps

4 questions, graded as you go.

Chapter 2

## Follow the profile

Solder profiles, then PID to track them.

Locked 250 XP

### Profiles

Follow a solder profile on a simulated oven: preheat, soak, reflow above the liquidus to the peak, and cool, for lead-free and leaded paste.

0 of 5 steps

Project Locked 500 XP

### PID tracking

Track the profile with PID and feed-forward instead of on/off, and compare the overshoot, the time above liquidus and the worst error.

0 of 5 steps

4 questions, graded as you go.

Chapter 3

## Make it safe

Cutoffs that fail safe, then a full run.

Locked 250 XP

### Safety cutoffs

Ring the controller with cutoffs that all fail safe: overtemp, a thermocouple fault, an open door, and a heater that does not warm the oven.

0 of 5 steps

Project Locked 530 XP

### Project: a solder profile

The finished controller: pick a paste, track its profile with PID, watch the door and the thermocouple every pass, and finish with a summary and a beep.

0 of 6 steps

4 questions, graded as you go.

Syllabus

## Every lesson in the course

All 6 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

### Measure and switch

- Thermocouples Measure an oven with a type K thermocouple and a MAX6675: the microvolts at the tip, the cold junction they are measured against, quarter degree steps and an open probe.
- SSR control Drive a solid-state relay from a pin, learn why zero-cross SSRs cannot be dimmed, and control power by switching for part of each one second window.

Chapter 2

### Follow the profile

- Profiles Follow a solder profile on a simulated oven: preheat, soak, reflow above the liquidus to the peak, and cool, for lead-free and leaded paste.
- PID tracking Track the profile with PID and feed-forward instead of on/off, and compare the overshoot, the time above liquidus and the worst error.

Chapter 3

### Make it safe

- Safety cutoffs Ring the controller with cutoffs that all fail safe: overtemp, a thermocouple fault, an open door, and a heater that does not warm the oven.
- Project: a solder profile The finished controller: pick a paste, track its profile with PID, watch the door and the thermocouple every pass, and finish with a summary and a beep.

Keep going

## The next course on your track

Build a reflow oven controller is part of the maker track, a ladder of courses from zero to expert.

Next course

### Build a robot arm

A four-servo arm set up and put to work like a technician does it: safe starts, limits and speeds, joystick control, inverse kinematics on a real linkage, teach and playback, a gripper that feels, and a pick-and-place cell.
Open the next course

Track

### Maker track

Follow the starter kit you already own, then build a claw machine, a balance bot, a handheld console or an LED cube, each a short course checked by the simulator.
See every course on the track

Kits

## Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

### Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kit

Questions

## About Build a reflow oven controller

Is Build a reflow oven controller free?

Yes. All 6 lessons of Build a reflow oven controller are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need a real Arduino Uno R3?

No. Every lesson runs on a simulated Arduino Uno R3 with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.

How long does Build a reflow oven controller take?

About 6 hours: 6 lessons in 3 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

What will I build?

Each chapter ends in a project that puts it together: SSR control, PID tracking and Project: a solder profile.

Where do I start?

With "Thermocouples", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.
