Source: https://mokxi.com/learn/path/build-pet-feeder
Updated: 2026-11-20

All paths

# Build a pet feeder

A first robot with a real job: a servo hatch, meals on a clock, portions weighed by a load cell, a snack button with a ration, and a log of every meal.

Arduino Uno R3 Free 6 lessons 5 h 3 chapters 1,330 XP Robotics · Beginner +100 XP

0 of 6 done

Start the course free A servo hatch Lesson plan for teachers

What you will build

## 2 projects, built step by step

6 lessons in 3 chapters, about 5 hours on a simulated Arduino Uno R3. Free, in your browser, every step checked by the simulator.

Chapter 1 project

### Schedules from an RTC

A DS3231 clock keeps time even with the power off. Watch a meal served on the minute, ask for an extra one, set the clock to dinner time, and write your own schedule.
Open it in the simulator

Chapter 2 project

### Logging meals

Did the cat eat? Keep a log of every meal, snack, skip and empty hopper, skip a meal when the bowl is still full, and read the day’s total.
Open it in the simulator

The map

## Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

## Open and on time

A servo hatch, then meals served on the minute by a real-time clock.

Open 165 XP

### A servo hatch

A servo opens a food hatch when you press a button and closes it again. Change how wide it opens and how long it stays open, the two numbers that decide a portion.

0 of 5 steps

Start What is in it

Project Locked 380 XP

### Schedules from an RTC

A DS3231 clock keeps time even with the power off. Watch a meal served on the minute, ask for an extra one, set the clock to dinner time, and write your own schedule.

0 of 6 steps

4 questions, graded as you go.

Chapter 2

## Weigh and keep track

Portions by weight, a rationed snack button, and a log of every meal.

Locked 190 XP

### Portion by weight

Put a load cell under the bowl and stop guessing. Weigh the bowl, serve a meal that closes the hatch on exactly 40 g, catch an empty hopper, and calibrate a different cell.

0 of 6 steps

Locked 140 XP

### A manual button

A snack button for the humans, with a daily ration so nobody overfeeds. Give a snack, run out of snacks, and set your own limit.

0 of 4 steps

Project Locked 330 XP

### Logging meals

Did the cat eat? Keep a log of every meal, snack, skip and empty hopper, skip a meal when the bowl is still full, and read the day’s total.

0 of 5 steps

5 questions, graded as you go.

Chapter 3

## Project: a two-meal feeder

Your pet’s times and portions, and a build sheet.

Locked 125 XP

### Project: a two-meal feeder

Make the feeder yours: check dinner, set your pet’s own times and portion, and write the build sheet for a real one.

0 of 4 steps

3 questions, graded as you go.

Syllabus

## Every lesson in the course

All 6 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

### Open and on time

- A servo hatch A servo opens a food hatch when you press a button and closes it again. Change how wide it opens and how long it stays open, the two numbers that decide a portion.
- Schedules from an RTC A DS3231 clock keeps time even with the power off. Watch a meal served on the minute, ask for an extra one, set the clock to dinner time, and write your own schedule.

Chapter 2

### Weigh and keep track

- Portion by weight Put a load cell under the bowl and stop guessing. Weigh the bowl, serve a meal that closes the hatch on exactly 40 g, catch an empty hopper, and calibrate a different cell.
- A manual button A snack button for the humans, with a daily ration so nobody overfeeds. Give a snack, run out of snacks, and set your own limit.
- Logging meals Did the cat eat? Keep a log of every meal, snack, skip and empty hopper, skip a meal when the bowl is still full, and read the day’s total.

Chapter 3

### Project: a two-meal feeder

- Project: a two-meal feeder Make the feeder yours: check dinner, set your pet’s own times and portion, and write the build sheet for a real one.

Keep going

## The next course on your track

Build a pet feeder is part of the maker track, a ladder of courses from zero to expert.

Next course

### Build a pocket oscilloscope

Turn an Uno and a TFT into a scope: fast sampling, a trigger, scales, measurements and a screen, honest about its limits.
Open the next course

Track

### Maker track

Follow the starter kit you already own, then build a claw machine, a balance bot, a handheld console or an LED cube, each a short course checked by the simulator.
See every course on the track

Kits

## Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

### Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kit

Questions

## About Build a pet feeder

Is Build a pet feeder free?

Yes. All 6 lessons of Build a pet feeder are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need a real Arduino Uno R3?

No. Every lesson runs on a simulated Arduino Uno R3 with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.

How long does Build a pet feeder take?

About 5 hours: 6 lessons in 3 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

What will I build?

Each chapter ends in a project that puts it together: Schedules from an RTC and Logging meals.

Where do I start?

With "A servo hatch", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.
