Source: https://mokxi.com/learn/path/build-load-cell-pedals
Updated: 2026-11-20

All paths

# Build load cell pedals

Sim racing pedals on a Pro Micro in three short lessons: a load cell brake on an HX711, a hall throttle and a pot clutch, and the curve that makes it feel right.

SparkFun Pro Micro Free 3 lessons 1 h 2 chapters 570 XP Maker · Intermediate +150 XP

0 of 3 done

Start the course free A brake that measures force Lesson plan for teachers

What you will build

## One project, built step by step

3 lessons in 2 chapters, about 1 hour on a simulated SparkFun Pro Micro. Free, in your browser, every step checked by the simulator.

Chapter 1 project

### Throttle and clutch

A hall sensor throttle and a pot clutch: calibrating two readings into a full 0 to 1023, with a little dead travel at each end.
Open it in the simulator

The map

## Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

## Force and position

A brake that weighs your push, and two pedals that measure travel.

Open 156 XP

### A brake that measures force

A beam load cell on an HX711: why a brake should read how hard you push rather than how far, taring at start-up, and counts per kilogram.

0 of 4 steps

Start What is in it

Project Locked 276 XP

### Throttle and clutch

A hall sensor throttle and a pot clutch: calibrating two readings into a full 0 to 1023, with a little dead travel at each end.

0 of 4 steps

Chapter 2

## The feel

A curve, a deadzone and a report that does not chatter.

Locked 138 XP

### The brake curve and the report

Shape the brake with a curve and a deadzone, keep load cell noise out of the report, and know what changes on a real Pro Micro.

0 of 4 steps

Syllabus

## Every lesson in the course

All 3 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

### Force and position

- A brake that measures force A beam load cell on an HX711: why a brake should read how hard you push rather than how far, taring at start-up, and counts per kilogram.
- Throttle and clutch A hall sensor throttle and a pot clutch: calibrating two readings into a full 0 to 1023, with a little dead travel at each end.

Chapter 2

### The feel

- The brake curve and the report Shape the brake with a curve and a deadzone, keep load cell noise out of the report, and know what changes on a real Pro Micro.

Keep going

## The next course on your track

Build load cell pedals is part of the maker track, a ladder of courses from zero to expert.

Next course

### Build a slot machine

Pull a real arcade lever, spin three OLED reels and pay out by a table whose odds you can check, on an Uno.
Open the next course

Track

### Maker track

Follow the starter kit you already own, then build a claw machine, a balance bot, a handheld console or an LED cube, each a short course checked by the simulator.
See every course on the track

Kits

## Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

### Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kit

Questions

## About Build load cell pedals

Is Build load cell pedals free?

Yes. All 3 lessons of Build load cell pedals are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need a real SparkFun Pro Micro?

No. Every lesson runs on a simulated SparkFun Pro Micro with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.

How long does Build load cell pedals take?

About 1 hour: 3 lessons in 2 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

What will I build?

Each chapter ends in a project that puts it together: Throttle and clutch.

Where do I start?

With "A brake that measures force", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.
