Source: https://mokxi.com/learn/path/build-hexapod-walker
Updated: 2026-11-20

All paths

# Build a hexapod walker

Six legs, twelve servos, real gaits: leg geometry, servo maps and calibration, a current budget, tripod, ripple and wave gaits with their support polygons, turning, terrain and a walking demo.

Arduino Uno R3 Free 7 lessons 7 h 3 chapters 2,493 XP Robotics · Advanced +250 XP

0 of 7 done

Start the course free Leg geometry Lesson plan for teachers

What you will build

## 2 projects, built step by step

7 lessons in 3 chapters, about 7 hours on a simulated Arduino Uno R3. Free, in your browser, every step checked by the simulator.

Chapter 1 project

### The current budget

Meter one side of the robot: six servos idle, then all moving. Scale it to 18 servos carrying a body, size the supply, and watch an undersized one collapse.
Open it in the simulator

Chapter 2 project

### Turning and terrain

Turn on the spot by walking the two sides opposite ways, add an arc turn, lift higher for rough ground, and move the center of mass forward until the tripod would tip.
Open it in the simulator

The map

## Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

## Legs and servos

The leg’s geometry, the pulse math and calibration, and the current twelve or eighteen servos draw.

Open 288 XP

### Leg geometry

Six legs with a hip and a knee each. Pose them from the Serial Monitor, see why the right side is mirrored, and work out the stride and the ground clearance from the leg’s lengths and angles.

0 of 6 steps

Start What is in it

Locked 288 XP

### Servo maps and calibration

An angle is a pulse width, and the PCA9685 sends it in ticks of 4.88 us. Map degrees to ticks, send a raw pulse, find the servo from another batch that stands off square, and trim it in code.

0 of 6 steps

Project Locked 500 XP

### The current budget

Meter one side of the robot: six servos idle, then all moving. Scale it to 18 servos carrying a body, size the supply, and watch an undersized one collapse.

0 of 5 steps

5 questions, graded as you go.

Chapter 2

## Gaits

Duty factor and phase: tripod, ripple and wave, stability margins, turning and rough ground.

Locked 288 XP

### Tripod gait

Two triangles of legs take turns. Walk the tripod gait, count the feet in the air, work out its speed from the duty factor, read its stability margin, and speed up the swing.

0 of 6 steps

Locked 250 XP

### Ripple and wave gaits

Keep more feet down. Switch to the ripple gait (duty 2/3) and the wave gait (duty 5/6), count the feet in the air, and trade speed for a stability margin almost twice as wide.

0 of 5 steps

Project Locked 576 XP

### Turning and terrain

Turn on the spot by walking the two sides opposite ways, add an arc turn, lift higher for rough ground, and move the center of mass forward until the tripod would tip.

0 of 6 steps

5 questions, graded as you go.

Chapter 3

## Project: a walking demo

A scripted demo from one button, extended and made safe.

Locked 303 XP

### Project: a walking demo

Script a demo the robot runs from one button: tripod forward, a turn, a careful wave. Add a turn, raise the lift for the careful part, and make a second press stop it safely.

0 of 7 steps

3 questions, graded as you go.

Syllabus

## Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

### Legs and servos

- Leg geometry Six legs with a hip and a knee each. Pose them from the Serial Monitor, see why the right side is mirrored, and work out the stride and the ground clearance from the leg’s lengths and angles.
- Servo maps and calibration An angle is a pulse width, and the PCA9685 sends it in ticks of 4.88 us. Map degrees to ticks, send a raw pulse, find the servo from another batch that stands off square, and trim it in code.
- The current budget Meter one side of the robot: six servos idle, then all moving. Scale it to 18 servos carrying a body, size the supply, and watch an undersized one collapse.

Chapter 2

### Gaits

- Tripod gait Two triangles of legs take turns. Walk the tripod gait, count the feet in the air, work out its speed from the duty factor, read its stability margin, and speed up the swing.
- Ripple and wave gaits Keep more feet down. Switch to the ripple gait (duty 2/3) and the wave gait (duty 5/6), count the feet in the air, and trade speed for a stability margin almost twice as wide.
- Turning and terrain Turn on the spot by walking the two sides opposite ways, add an arc turn, lift higher for rough ground, and move the center of mass forward until the tripod would tip.

Chapter 3

### Project: a walking demo

- Project: a walking demo Script a demo the robot runs from one button: tripod forward, a turn, a careful wave. Add a turn, raise the lift for the careful part, and make a second press stop it safely.

Keep going

## The next course on your track

Build a hexapod walker is part of the maker track, a ladder of courses from zero to expert.

Next course

### Build a line-following racer

A line-following race car taught as real control engineering: a five-sensor array, the line’s position in millimeters, differential drive on a TB6612, P then PD steering, speed against grip, and lap timing with a wheel encoder.
Open the next course

Track

### Maker track

Follow the starter kit you already own, then build a claw machine, a balance bot, a handheld console or an LED cube, each a short course checked by the simulator.
See every course on the track

Kits

## Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

### Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kit

Questions

## About Build a hexapod walker

Is Build a hexapod walker free?

Yes. All 7 lessons of Build a hexapod walker are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need a real Arduino Uno R3?

No. Every lesson runs on a simulated Arduino Uno R3 with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.

How long does Build a hexapod walker take?

About 7 hours: 7 lessons in 3 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

What will I build?

Each chapter ends in a project that puts it together: The current budget and Turning and terrain.

Where do I start?

With "Leg geometry", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.
