Source: https://mokxi.com/learn/path/build-bench-tools
Updated: 2026-11-20

All paths

# Build your own bench tools

A frequency counter, a capacitance meter, a resistor tester, a battery tester and a DAC signal generator, then all five in one LCD box.

Arduino Uno R3 Free 6 lessons 5 h 3 chapters 1,902 XP Maker · Intermediate +150 XP

0 of 6 done

Start the course free A frequency counter Lesson plan for teachers

What you will build

## 3 projects, built step by step

6 lessons in 3 chapters, about 5 hours on a simulated Arduino Uno R3. Free, in your browser, every step checked by the simulator.

Chapter 1 project

### A capacitance meter

Charge a capacitor through 10k, time how long it takes to reach 63.2% of the supply, and that time is R x C: a capacitance meter from one resistor and a stopwatch.
Open it in the simulator

Chapter 2 project

### A battery tester

Run an AA cell into a 10 ohm load through an INA219, add up the milliamp-hours every second, and stop at 0.9 V with the capacity it really delivered.
Open it in the simulator

Chapter 3 project

### One box, five tools

Put all five instruments behind one 16x2 LCD and a MENU button: frequency, capacitance, resistance, battery and a DAC staircase, the same numbers as the lessons before.
Open it in the simulator

The map

## Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

## Measure time

Count edges in a gate and time a capacitor charging.

Open 236 XP

### A frequency counter

Count the rising edges of a signal for exactly one second with an interrupt, and see how the gate sets the resolution and where the meter stops being right.

0 of 6 steps

Start What is in it

Project Locked 410 XP

### A capacitance meter

Charge a capacitor through 10k, time how long it takes to reach 63.2% of the supply, and that time is R x C: a capacitance meter from one resistor and a stopwatch.

0 of 5 steps

4 questions, graded as you go.

Chapter 2

## Parts and power

Resistors by divider and batteries by the milliamp-hour.

Locked 205 XP

### A component tester

Read an unknown resistor with a known 10k and the ADC, work out its color bands, and see why a two-resistor meter is sharp in the middle and blunt at the ends.

0 of 5 steps

Project Locked 410 XP

### A battery tester

Run an AA cell into a 10 ohm load through an INA219, add up the milliamp-hours every second, and stop at 0.9 V with the capacity it really delivered.

0 of 5 steps

5 questions, graded as you go.

Chapter 3

## Signals and the box

A DAC that makes voltages, then all five tools in one box.

Locked 205 XP

### A signal generator

Set any voltage from 0 to 5 V in 1.2 mV steps with an MCP4725 DAC, then step a 32-point sine table out of it at 5 Hz.

0 of 5 steps

Project Locked 436 XP

### One box, five tools

Put all five instruments behind one 16x2 LCD and a MENU button: frequency, capacitance, resistance, battery and a DAC staircase, the same numbers as the lessons before.

0 of 6 steps

4 questions, graded as you go.

Syllabus

## Every lesson in the course

All 6 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

### Measure time

- A frequency counter Count the rising edges of a signal for exactly one second with an interrupt, and see how the gate sets the resolution and where the meter stops being right.
- A capacitance meter Charge a capacitor through 10k, time how long it takes to reach 63.2% of the supply, and that time is R x C: a capacitance meter from one resistor and a stopwatch.

Chapter 2

### Parts and power

- A component tester Read an unknown resistor with a known 10k and the ADC, work out its color bands, and see why a two-resistor meter is sharp in the middle and blunt at the ends.
- A battery tester Run an AA cell into a 10 ohm load through an INA219, add up the milliamp-hours every second, and stop at 0.9 V with the capacity it really delivered.

Chapter 3

### Signals and the box

- A signal generator Set any voltage from 0 to 5 V in 1.2 mV steps with an MCP4725 DAC, then step a 32-point sine table out of it at 5 Hz.
- One box, five tools Put all five instruments behind one 16x2 LCD and a MENU button: frequency, capacitance, resistance, battery and a DAC staircase, the same numbers as the lessons before.

Keep going

## The next course on your track

Build your own bench tools is part of the maker track, a ladder of courses from zero to expert.

Next course

### Build a cat laser toy

Your first robot: a pan and tilt laser turret on two servos that plays with a cat on its own, with random glides, tuned speed and pauses, real laser eye safety, a session timer, and a toy at the end of every game.
Open the next course

Track

### Maker track

Follow the starter kit you already own, then build a claw machine, a balance bot, a handheld console or an LED cube, each a short course checked by the simulator.
See every course on the track

Kits

## Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

### Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kit

Questions

## About Build your own bench tools

Is Build your own bench tools free?

Yes. All 6 lessons of Build your own bench tools are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need a real Arduino Uno R3?

No. Every lesson runs on a simulated Arduino Uno R3 with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.

How long does Build your own bench tools take?

About 5 hours: 6 lessons in 3 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

What will I build?

Each chapter ends in a project that puts it together: A capacitance meter, A battery tester and One box, five tools.

Where do I start?

With "A frequency counter", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.
