Source: https://mokxi.com/learn/path/battery-management-systems
Updated: 2026-11-20

All paths

# Battery management systems

What a BMS measures and why: chemistries, series strings, balancing, state of charge, protection and charging, ending in a 2S pack monitor you wire and set for your own pack.

Free 7 lessons 6 h 7 chapters 1,765 XP Electrical · Advanced +250 XP

0 of 7 done

Start the course free Chemistries: what a cell's voltage tells you Lesson plan for teachers

What you will build

## 0 projects, built step by step

7 lessons in 7 chapters, about 6 hours on a simulated breadboard. Free, in your browser, every step checked by the simulator.

The map

## Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

## Chemistries

Full, empty and nominal, and the resistance inside a cell.

Open 288 XP

### Chemistries: what a cell's voltage tells you

One 18650 on a meter and a 4 ohm load: 4.2 V full, 3.0 V empty, the sag under load from internal resistance, a small pouch that sags more, and how lithium-ion, LiFePO4, NiMH and lead-acid compare.

0 of 6 steps

Start What is in it

4 questions, graded as you go.

Chapter 2

## Series strings

2S adds voltages, and the weakest cell sets the end.

Locked 250 XP

### Series strings: 2S and the weakest cell

Two 18650s in series make 8.4 V: the same current through both, a mismatched cell, and a weak cell that hits empty while the pack voltage still looks healthy, which is why a BMS measures every cell.

0 of 5 steps

4 questions, graded as you go.

Chapter 3

## Balancing

A bleed resistor and a MOSFET per cell.

Locked 250 XP

### Balancing: bleeding the high cell

A 2S pack 0.24 V out of balance: a bleed resistor and an AO3400A drain the high cell alone, watch it come down to its neighbor, work out the heat, and balance the bottom cell too.

0 of 5 steps

3 questions, graded as you go.

Chapter 4

## State of charge

Volts against counted coulombs, and a capacity that fades.

Locked 212 XP

### State of charge: volts and coulombs

An Uno watches a 2S pack with a cell tap, a divider and an INA219: state of charge from the lowest cell's voltage, and by counting the charge that flows out, which agree until the capacity is wrong.

0 of 4 steps

3 questions, graded as you go.

Chapter 5

## Protection

Overcurrent, undervoltage and imbalance, latched until reset.

Locked 250 XP

### Protection: the MOSFET that says no

The pack monitor opens its low-side MOSFET on overcurrent, latches until reset, cuts off a weak cell at 3.0 V, takes a higher undervoltage setting, and warns of imbalance.

0 of 5 steps

4 questions, graded as you go.

Chapter 6

## Charging profiles

Constant current, constant voltage and the end of charge.

Locked 227 XP

### Charging profiles: CC, then CV, then stop

A TP4056 charges one 18650: a constant 1 A, the cell voltage climbing, the switch to constant 4.2 V as the current tapers, and the standby lamp at the end, with the rules for charging lithium safely.

0 of 5 steps

4 questions, graded as you go.

Chapter 7

## Boss build

A 2S monitor with your own limits.

Locked 288 XP

### Boss: a 2S pack monitor

Wire the protection MOSFET, then run a 2S monitor that watches each cell, counts the charge out, trips on overcurrent and undervoltage, and takes the limits you set for your own pack.

0 of 6 steps

3 questions, graded as you go.

Syllabus

## Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

### Chemistries

- Chemistries: what a cell's voltage tells you One 18650 on a meter and a 4 ohm load: 4.2 V full, 3.0 V empty, the sag under load from internal resistance, a small pouch that sags more, and how lithium-ion, LiFePO4, NiMH and lead-acid compare.

Chapter 2

### Series strings

- Series strings: 2S and the weakest cell Two 18650s in series make 8.4 V: the same current through both, a mismatched cell, and a weak cell that hits empty while the pack voltage still looks healthy, which is why a BMS measures every cell.

Chapter 3

### Balancing

- Balancing: bleeding the high cell A 2S pack 0.24 V out of balance: a bleed resistor and an AO3400A drain the high cell alone, watch it come down to its neighbor, work out the heat, and balance the bottom cell too.

Chapter 4

### State of charge

- State of charge: volts and coulombs An Uno watches a 2S pack with a cell tap, a divider and an INA219: state of charge from the lowest cell's voltage, and by counting the charge that flows out, which agree until the capacity is wrong.

Chapter 5

### Protection

- Protection: the MOSFET that says no The pack monitor opens its low-side MOSFET on overcurrent, latches until reset, cuts off a weak cell at 3.0 V, takes a higher undervoltage setting, and warns of imbalance.

Chapter 6

### Charging profiles

- Charging profiles: CC, then CV, then stop A TP4056 charges one 18650: a constant 1 A, the cell voltage climbing, the switch to constant 4.2 V as the current tapers, and the standby lamp at the end, with the rules for charging lithium safely.

Chapter 7

### Boss build

- Boss: a 2S pack monitor Wire the protection MOSFET, then run a 2S monitor that watches each cell, counts the charge out, trips on overcurrent and undervoltage, and takes the limits you set for your own pack.

Kits

## Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

### Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kit

Questions

## About Battery management systems

Is Battery management systems free?

Yes. All 7 lessons of Battery management systems are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need any parts?

No. Every circuit is built on a simulated breadboard, and the simulator checks each step as you go. When you want to build it for real, the same parts and wiring work on a real bench.

How long does Battery management systems take?

About 6 hours: 7 lessons in 7 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

Where do I start?

With "Chemistries: what a cell's voltage tells you", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.
