Source: https://mokxi.com/learn/path/alarm-and-security-circuits
Updated: 2026-11-20

All paths

# Low-voltage alarm circuits

How a burglar alarm thinks: NC loops, end-of-line and supervised zones, sirens and strobes, keypads and arming, battery backup, and a four-zone panel you wire and make your own.

Free 7 lessons 6 h 7 chapters 1,727 XP Electrical · Intermediate +150 XP

0 of 7 done

Start the course free Normally closed loops: why alarms are wired backwards Lesson plan for teachers

What you will build

## 0 projects, built step by step

7 lessons in 7 chapters, about 6 hours on a simulated breadboard. Free, in your browser, every step checked by the simulator.

The map

## Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

## Normally closed loops

Contacts in series that fail safe, and an NO button that fails silently.

Open 249 XP

### Normally closed loops: why alarms are wired backwards

Three door contacts in series hold a MOSFET off: open any door and the alarm lamp lights, cut the wire and it lights too. The same test on a normally open panic button shows why alarms fail safe.

0 of 7 steps

Start What is in it

4 questions, graded as you go.

Chapter 2

## End-of-line resistors

A resistor at the far end lets the panel see a jumper.

Locked 236 XP

### End-of-line resistors: seeing the wire itself

A 4.7k resistor at the far end of the loop gives the panel a middle voltage to expect: a door reads high, a burglar's jumper reads low, and a plain loop cannot tell the jumper from a shut door.

0 of 6 steps

4 questions, graded as you go.

Chapter 3

## Supervised zones

Double end-of-line: normal, open, cut and short on two wires.

Locked 205 XP

### Supervised zones: four states on two wires

Double end-of-line wiring: a resistor in series and another across the contact give a panel four voltages, so it tells a shut door, an open door, a cut wire and a short apart.

0 of 5 steps

4 questions, graded as you go.

Chapter 4

## Sirens and strobes

A MOSFET bell output, its current, and the run that silences a siren.

Locked 236 XP

### Sirens and strobes: the bell output

A MOSFET switches a 12 V siren and a strobe at the end of a wire run: their current, why a long thin run can silence a siren, and adding a second siren to the bell output.

0 of 6 steps

4 questions, graded as you go.

Chapter 5

## Keypads and arming

An Uno panel: away, stay, exit and entry delays, and not-ready zones.

Locked 267 XP

### Keypads and arming: an Uno becomes a panel

An Uno reads three DEOL zones on its analog pins, a PIR and a 4x4 keypad: arm away, the exit delay, not-ready zones, the entry delay, an alarm with siren and strobe, and arming stay.

0 of 7 steps

4 questions, graded as you go.

Chapter 6

## Battery backup

A float charger and a lead-acid battery that take over without a gap.

Locked 236 XP

### Battery backup: an alarm that works in a power cut

A 13.8 V charger, a 12 V 7 Ah lead-acid battery and a panel on one bus: watch the battery current change sign when the power fails, carry the siren, and drain, and work out standby time.

0 of 6 steps

4 questions, graded as you go.

Chapter 7

## Boss build

Wire a zone, walk test, change the code, bypass, catch a tamper, set the bell cutoff.

Locked 298 XP

### Boss: a four-zone panel

Wire the window's DEOL loop, walk test every zone, change the master code, bypass a zone, catch a tamper and set your own bell cutoff: a four-zone panel with keypad, siren and strobe, made yours.

0 of 8 steps

4 questions, graded as you go.

Syllabus

## Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

### Normally closed loops

- Normally closed loops: why alarms are wired backwards Three door contacts in series hold a MOSFET off: open any door and the alarm lamp lights, cut the wire and it lights too. The same test on a normally open panic button shows why alarms fail safe.

Chapter 2

### End-of-line resistors

- End-of-line resistors: seeing the wire itself A 4.7k resistor at the far end of the loop gives the panel a middle voltage to expect: a door reads high, a burglar's jumper reads low, and a plain loop cannot tell the jumper from a shut door.

Chapter 3

### Supervised zones

- Supervised zones: four states on two wires Double end-of-line wiring: a resistor in series and another across the contact give a panel four voltages, so it tells a shut door, an open door, a cut wire and a short apart.

Chapter 4

### Sirens and strobes

- Sirens and strobes: the bell output A MOSFET switches a 12 V siren and a strobe at the end of a wire run: their current, why a long thin run can silence a siren, and adding a second siren to the bell output.

Chapter 5

### Keypads and arming

- Keypads and arming: an Uno becomes a panel An Uno reads three DEOL zones on its analog pins, a PIR and a 4x4 keypad: arm away, the exit delay, not-ready zones, the entry delay, an alarm with siren and strobe, and arming stay.

Chapter 6

### Battery backup

- Battery backup: an alarm that works in a power cut A 13.8 V charger, a 12 V 7 Ah lead-acid battery and a panel on one bus: watch the battery current change sign when the power fails, carry the siren, and drain, and work out standby time.

Chapter 7

### Boss build

- Boss: a four-zone panel Wire the window's DEOL loop, walk test every zone, change the master code, bypass a zone, catch a tamper and set your own bell cutoff: a four-zone panel with keypad, siren and strobe, made yours.

Kits

## Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

### Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kit

Questions

## About Low-voltage alarm circuits

Is Low-voltage alarm circuits free?

Yes. All 7 lessons of Low-voltage alarm circuits are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need any parts?

No. Every circuit is built on a simulated breadboard, and the simulator checks each step as you go. When you want to build it for real, the same parts and wiring work on a real bench.

How long does Low-voltage alarm circuits take?

About 6 hours: 7 lessons in 7 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

Where do I start?

With "Normally closed loops: why alarms are wired backwards", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.
