Source: https://mokxi.com/learn/arduino-mlx90614 Updated: 2026-11-02 Learn # An MLX90614 on an Arduino: a no-touch thermometer Beginner Written by the Mokxi team, updated November 2, 2026 Start building free Open the editor Or see every lesson. - 505 parts on the bench - 45 boards running now - 1.00x real time, on every board Click to open it in the editor The Fever thermometer example: drag the object temperature on the GY-906 past 38 C and the LCD says FEVER. The MLX90614 reads the temperature of whatever it points at without touching it. It is the sensor inside many forehead thermometers and the little "IR thermometer" guns, and it comes on a small GY-906 board with four pins that plug straight into an Arduino’s I2C bus. The circuit above is an Uno, an MLX90614 and a 16x2 LCD with an I2C backpack, sharing one bus, plus a piezo on pin 8. Twice a second the LCD shows the forehead’s temperature and the room’s; over 38.0 C (100.4 F) the first line says FEVER and the piezo beeps. Press Run, then drag the object slider on the sensor past 38 and listen. ## What you need - An Arduino Uno - An MLX90614 module (GY-906) - A 16x2 LCD with an I2C backpack (address 0x27) - A passive piezo - A breadboard and jumper wires ## Wiring Part and pin | Goes to | Note MLX90614 VIN | 5 V | The GY-906 runs on 3 to 5 V MLX90614 GND | GND | MLX90614 SDA | SDA (A4) | Shares the bus with the LCD MLX90614 SCL | SCL (A5) | LCD VCC and GND | 5 V and GND | LCD SDA and SCL | A4 and A5 | The same two bus wires Piezo | Pin 8 | Other leg to GND ## How a thermometer reads without touching Everything warmer than absolute zero gives off infrared light, and the warmer it is, the more it gives off. Behind the MLX90614’s window is a thermopile, a stack of tiny junctions that warm up a little when infrared falls on them. A second sensor inside measures the can itself. The chip compares the two and works out the temperature of what is in front of it. So you get two numbers: the object temperature (what it sees) and the ambient temperature (its own, which is about the room’s). The chip keeps both in memory, and an Arduino reads them over I2C at address 0x5A. The value is stored in fiftieths of a kelvin; the library turns it into degrees Celsius for you. ## The sketch The sketch reads both temperatures, multiplies by 10 and rounds, so it can work in whole tenths of a degree: 36.6 C becomes 366. That makes the fever check a plain whole-number comparison, object > 380, and keeps the display to one decimal place. When the forehead is over 380 tenths, the first line reads FEVER and tone(PIEZO, 2000, 150) gives a short 2000 Hz beep, once for each reading while the fever lasts. At exactly 38.0 there is no beep; at 38.1 there is. Run it and drag the slider to see. The serial monitor gets the same reading, "forehead 36.6 C" at the start, with "FEVER" on the end of the line when it is over. The fever thermometer’s loop, trimmed ## Two sensors on one I2C bus The LCD backpack is at 0x27 and the MLX90614 at 0x5A, so both hang on the same two wires and the Uno talks to each by its address. That is the point of I2C: up to dozens of parts on two pins, as long as no two share an address. Watch for parts that do share 0x5A. The MPR121 touch sensor lives there too, so the two cannot share a bus unless you move the MPR121’s address. If you are not sure what is on your bus, run an I2C scanner first (see the I2C page below). ## Getting a real reading A real MLX90614 sees a cone, not a dot. The common GY-906 (the MLX90614ESF-AAA) has a 90 degree field of view, so at 10 cm it averages a circle about 20 cm wide. Hold it a couple of centimeters from a forehead, or it reads the wall behind as well. Shiny things lie. The chip assumes the surface gives off infrared like skin does (an emissivity of 1.0, close to skin’s 0.98). Polished metal gives off much less, so it reads far too cold. The library can change the emissivity with writeEmissivity(), but it is stored in the chip’s memory, so most people leave it alone and put tape on a metal part instead. Also, a forehead reads cooler than the inside of your body, so a medical thermometer adds a correction. This project is a demo for learning, not a medical device. ## Common mistakes The sensor not found. With SDA pulled out, mlx.begin() fails, the LCD says "No MLX90614" and the sketch stops. Check SDA, SCL and power. Measuring from too far away, so the reading is the room’s average, not the object’s. Another part at 0x5A on the same bus, such as an MPR121. Pointing it at glass or shiny metal and believing the number. Infrared does not pass through glass, so through a window it reads the glass. Comparing floats for the alarm and getting a beep that flickers at the limit. Rounding to whole tenths, as this sketch does, keeps the check steady. Open this circuit in the editor. Arduino Uno: an MLX90614 fever thermometer, wired as it runs at the top of this page. Change a part or a value and run it again. Open the circuit ## Questions What library do I need for the MLX90614? The Adafruit MLX90614 Library. Call mlx.begin(), then mlx.readObjectTempC() for what it points at and mlx.readAmbientTempC() for its own temperature. There are F versions for Fahrenheit. What is the MLX90614 I2C address? 0x5A by default. It can be changed in the chip’s memory, which is how two of them share a bus. How accurate is the MLX90614? About 0.5 C around room and body temperature, by the datasheet, for a surface that fills its field of view. The medical grade version is better, around 0.2 C. Can it measure through glass? No. Glass blocks the infrared it reads, so it measures the glass. Related ## Keep going I2C Explained: Addresses, Acknowledges and Pull-Ups Arduino LCD I2C 16x2: Wiring, Code, Scrolling Text Arduino Buzzer and Piezo: Beeps, Notes, Metronome Arduino TMP36 Temperature Sensor in °F and °C Arduino MAX30102 Pulse Oximeter: Code and Wiring How the MLX90614 is modeled The I2C LCD, pin by pin The Arduino Uno simulator The project page, with the full sketch Beginner ## Build this for real Open the editor, change a value and watch the number move with it. Nothing to install, and no account needed. Start building free Open the editor