Source: https://mokxi.com/learn/arduino-bmp180 Updated: 2026-10-25 Learn # A BMP180 on an Arduino: pressure, temperature and altitude Intermediate Written by the Mokxi team, updated October 25, 2026 Start building free Open the editor Or see every lesson. - 455 parts on the bench - 43 boards running now - 1.00x real time, on every board Click to open it in the editor The Barometer example on a simulated ATmega328P: drag the temperature and pressure sliders on the GY-68. The BMP180 is a tiny Bosch barometer: it measures air pressure, and the temperature beside it, and talks to an Arduino over I2C. It is the chip on the purple GY-68 breakout that comes in many sensor kits, and it is the classic first way to make a weather station or an altimeter. The circuit above is an Uno reading a BMP180 with the Adafruit BMP085 library (the BMP180 is the BMP085’s successor and uses the same code). Twice a second it prints the temperature, the pressure in pascals and the altitude that pressure works out to. Press Run, then drag the two sliders on the breakout and watch the numbers follow. ## What you need - An Arduino Uno - A BMP180 breakout (GY-68) - Four jumper wires - A breadboard (optional) ## Wiring Part and pin | Goes to | Note BMP180 VCC | 5 V | The GY-68 has its own 3.3 V regulator, so 5 V is fine BMP180 GND | GND | BMP180 SDA | A4 | The Uno’s I2C data pin BMP180 SCL | A5 | The Uno’s I2C clock pin BMP180 3V3 | Nothing | The regulator’s output; leave it free ## What the BMP180 measures Air has weight, and the pressure of all the air above you pushes on everything at about 101,325 pascals at sea level. That is 1013.25 hectopascals (hPa), the same thing as millibars, or 29.92 inches of mercury on a US weather report. Climb a hill and there is less air above you, so the pressure drops by about 12 Pa for every meter near sea level. Inside the BMP180 is a small membrane that bends with the pressure, and a temperature sensor next to it. The chip does not hand over pascals, though. It gives raw counts and eleven calibration numbers stored at the factory, and the library runs the datasheet’s math to turn them into a temperature to a tenth of a degree and a pressure to one pascal. The chip sits at I2C address 0x77, and only there, so one Uno can read one BMP180 on its bus. ## The sketch bmp.begin() checks that the chip answers with its ID and reads the calibration. If it fails, the sketch prints the library’s famous line, "Could not find a valid BMP085 sensor, check wiring!", and stops. Then every half second it prints three readings. The barometer sketch ## Why the altitude is only a guess readAltitude() uses the standard barometric formula: altitude = 44330 x (1 - (p / p0) ^ 0.1903), where p is the pressure you measured and p0 is the pressure at sea level. By default p0 is the standard 101,325 Pa, which is only true on an average day. Weather moves the sea-level pressure up and down by 30 hPa or more, and at about 8 meters per hectopascal that shifts the altitude by tens of meters while the sensor sits still on your desk. So a barometer can tell you very well how much you climbed in the last ten minutes, and only roughly how high you are. To get a true altitude, look up today’s sea-level pressure for your area (weather services list it, often as "pressure" or "QNH") and pass it in: bmp.readAltitude(102000) for 1020 hPa. Or go the other way: if you know your height, bmp.readSealevelPressure(250) gives the sea-level pressure for a sensor 250 meters up, which is the number weather maps show. ## BMP180, BMP280 or BME280? Bosch stopped making the BMP180 years ago, and you mostly find it in older kits now. Its replacement, the BMP280, is more exact and also talks SPI. The BME280 adds humidity. Both need a different library (Adafruit_BMP280 or Adafruit_BME280), since their registers are different, but the idea and the altitude math are the same. If your board says BMP280 and this sketch says it cannot find the sensor, that is the reason: the BMP085 library looks for the BMP180’s chip ID, 0x55, and a BMP280 answers 0x58. ## Common mistakes SDA and SCL swapped, or one of them loose. The library cannot find the chip and prints "Could not find a valid BMP085 sensor, check wiring!". Swap A4 and A5 in the circuit above and you get exactly that. Trusting the altitude to the meter. It is pressure, turned into height with a guess about the weather. Give it today’s sea-level pressure, or only use the change. Using the BMP085 library on a BMP280 or BME280. The chip ID does not match, so begin() fails. Use the library for your chip. Putting the sensor next to something warm, like the Uno’s regulator, or in direct sun. The temperature reading is the chip’s own, so it reads the heat around it, not the room. Reading faster than the chip converts. A pressure reading at the highest accuracy takes 25.5 ms. The library waits for you, but a sketch that writes to the chip by hand has to wait too, or it reads the last result again. ## Questions How do I connect a BMP180 to an Arduino Uno? Four wires: VCC to 5 V, GND to GND, SDA to A4 and SCL to A5. The GY-68 board has a regulator and pull-up resistors, so nothing else is needed. Which library do I use for a BMP180? The Adafruit BMP085 Library. The BMP180 kept the BMP085’s registers, so the same library and calls work: bmp.begin(), bmp.readTemperature(), bmp.readPressure() and bmp.readAltitude(). Why does my BMP180 altitude change when I have not moved? Because the weather changes the air pressure, and the altitude is worked out from pressure. Pass today’s sea-level pressure to readAltitude() for a better number. What is the BMP180 I2C address? 0x77. It cannot be changed, so you cannot put two of them on one I2C bus without a multiplexer. Related ## Keep going I2C Explained: Addresses, Acknowledges and Pull-Ups Arduino BME680: Air Quality, Gas and Weather Arduino DHT22 and DHT11: Temperature and Humidity Arduino DS18B20 Temperature Sensor: Wiring and Code Arduino LCD I2C 16x2: Wiring, Code, Scrolling Text How the BMP180 is modeled Two barometers on an ESP32-C3, a BMP280 beside a BME280 Intermediate The Arduino Uno simulator The project page, with the full sketch Intermediate ## Build this for real Open the editor, change a value and watch the number move with it. Nothing to install, and no account needed. Start building free Open the editor