Source: https://mokxi.com/kits/companion/sunfounder-starter-kit-uno-r3
Updated: 2026-11-07

Kits / Kit companions
Kit companion

# SunFounder Starter Kit for Arduino Uno R3: every lesson, simulated

The kit’s 23 C lessons, in order, each as a circuit that runs in your browser on the pins the lesson uses. Open one beside the tutorial and compare it jumper for jumper.

Open the first lesson Find your lesson What else it can build

Not affiliated with SunFounder. Lesson titles are referenced so you can follow along.

Lesson by lesson

## Every lesson in the kit’s order

Lesson numbers and titles follow the 23 C lessons of the online tutorial "For UNO User" (the 19 Scratch lessons are not covered). Each circuit uses the kit’s parts on the pins the lesson uses.

23 of the 23 lessons with a circuit run here, 1 of them with a change we name.

1

### Blinking LED

Runs here

An LED with a 220 ohm resistor on pin 9, blinking once a second.

Open in the editor Blink an LED on pin 9

2

### Flowing LED Lights

Runs here

Eight LEDs on pins 2 to 9 lit one after another by a for loop.

Open in the editor Flowing lights on pins 2 to 9

3

### Controlling LED by Button

Runs here

A button on pin 12 with a 10k pull-down lights the LED on pin 13.

The 0.1 uF debounce capacitor is left out; the sketch filters the bounce instead.

Open in the editor Button on pin 12 lights the LED on pin 13

4

### Doorbell

Runs here

A button on pin 2 rings a buzzer on pin 8.

The 0.1 uF debounce capacitor is left out; the sketch filters the bounce instead.

Open in the editor Doorbell: button on pin 2, buzzer on pin 8

5

### Tilt Switch

Runs here

Tip the switch on pin 2 and the LED on pin 13 lights.

Open in the editor Tilt switch

6

### Relay

Runs here

Pin 8 drives a transistor that pulls in a relay, and the relay lights an LED.

Open in the editor Relay on pin 8 through a transistor

7

### RGB LED

Runs here

Red on pin 11, green on 10, blue on 9, showing seven colors.

Open in the editor RGB colors on pins 11, 10 and 9

8

### Controlling an LED by Potentiometer

Runs here

A knob on A0 sets the brightness of an LED on pin 9.

Open in the editor Knob on A0 dims the LED on pin 9

9

### Photo resistor

Runs here

A photoresistor on A0 lights up to eight LEDs on pins 5 to 12.

Open in the editor Light meter: photoresistor on A0, LEDs on pins 5 to 12

10

### Servo

Runs here

A servo on pin 9 moving through its range.

Open in the editor Servo sweep

11

### LCD1602

Runs here

A 16x2 LCD on pins 4, 6 and 10 to 13, with a scrolling line.

The contrast knob is left out: the simulated display is always readable, so V0 goes to ground.

Open in the editor LCD1602 on pins 4, 6 and 10 to 13

12

### Thermistor

Runs here

A thermistor on A0 with a 10k pull-up, read out on the LCD in both scales.

The contrast knob is left out: the simulated display is always readable, so V0 goes to ground.

Open in the editor Thermistor on A0, degrees on an LCD (pins 4, 6, 10 to 13)

13

### Ultrasonic

Runs here

An HC-SR04 on pins 2 and 3, the distance on the LCD.

The contrast knob is left out: the simulated display is always readable, so V0 goes to ground.

Open in the editor Ultrasonic distance on an LCD (TRIG 2, ECHO 3)

14

### Infrared-Receiver

Runs here

An IR receiver on pin 2 names the remote’s buttons.

The simulated remote’s buttons may be labeled differently from the one in your box; the decoding is the same.

Open in the editor IR receiver on pin 2

15

### Humiture Sensor

Runs here

A DHT11 on pin 3, temperature and humidity on the LCD.

The contrast knob is left out: the simulated display is always readable, so V0 goes to ground.

Open in the editor DHT11 on pin 3, readings on an LCD

16

### Joystick PS2

Runs here

X on A0, Y on A1 and the switch on pin 8.

Open in the editor Joystick on A0, A1 and pin 8

17

### 7-Segment Display

Runs, with a change

A seven-segment digit wired straight to pins 4 to 11, counting 0 to 9.

One 220 ohm resistor on the common pin stands in for the lesson’s resistor on every segment.

Open in the editor Seven-segment digit on pins 4 to 11

18

### 74HC595

Runs here

A 74HC595 on pins 11, 8 and 12 shows 0 to F on one digit.

Here Q0 to Q6 drive segments a to g; if your wiring puts them the other way around, reverse the bit patterns in the sketch.

Open in the editor Hex digits through a 74HC595 (pins 11, 8 and 12)

19

### Stepper Motor

Runs here

A stepper on pins 2 to 5 follows a knob on A0.

Open in the editor Stepper follows a knob (pins 2 to 5)

20

### Simple Creation-Stopwatch

Runs here

A four-digit display, segments on 2 to 9 and digits on 13 to 10, counting seconds.

Open in the editor Stopwatch on a four-digit display

21

### Simple Creation-Answer Machine

Runs here

Three answer buttons, a reset button, four LEDs and a buzzer: first to press wins.

Open in the editor Quiz buzzer for three players

22

### Simple Creation-Small Fan

Runs here

A button on pin 2 steps a motor on an L293D (pins 9 and 10) through three speeds.

The 0.1 uF debounce capacitor is left out; the sketch filters the bounce instead.

Open in the editor Three-speed fan on an L293D (pins 9 and 10)

23

### Simple Creation - Digital Dice

Runs here

A digit on a 74HC595 spins; a button on pin 2 stops it on a roll.

The 0.1 uF debounce capacitor is left out; the sketch filters the bounce instead.

Open in the editor Digital dice on a 74HC595 (pins 11, 8 and 12)

Lesson list and pins read from SunFounder’s online tutorial. The explanations on this page are our own.

Learning path

## Everything the SunFounder Starter Kit for Arduino Uno R3 can build

142 projects use only the parts in this box, ordered from a first blink to the hardest.

Beginner (82)

- EEPROM: memory that survives a reset
- Serial echo: the board repeats what you type
- Active buzzer
- Active buzzer module on pin 3
- DHT11 temperature and humidity
- DHT11 module on pin 4
- DHT11 temperature and humidity on pin 10
- Joystick on A0, A1 and pin 2
- Joystick module: A0, A1 and pin 3
- Joystick on A0, A1 and pin 8
- LCD1602 on pins 4, 6 and 10 to 13
- LCD1602 on pins 7 to 12
- LCD1602 hello
- Morse code on an active buzzer (pin 9)
- Pomodoro timer on an active buzzer (pin 9)
- Servo sweep
- Servo sweep on pin 10
- Servo sweep on pin 3
- Ultrasonic distance on pins 12 and 11
- Ultrasonic sensor on 8 and 7, the LED on 13 when out of range
- Stepper motor on pins 8 to 11
- Read a knob
- Operating point and sweep
- Fade an LED
- First blink
- IR decoder
- Blink an LED on pin 13, once a second
- Blink an LED on pin 3
- Blink an LED on pin 8
- Blink an LED on pin 9
- Breathing LED on pin 5
- Button on pin 12 lights the LED on pin 13
- Answer ball
- Flowing lights on pins 2 to 9
- IR remote codes on pin 12
- IR receiver module on pin 11
- IR receiver on pin 2
- LED module on pin 7, blinking
- An LED on the 5 V pin
- Mood dial
- Four brightnesses from PWM: pins 5, 6, 9 and 10
- RGB colors on pins 11, 10 and 9
- RGB LED on pins 3, 5 and 6
- RGB fade on pins 6, 5 and 3
- RGB LED module: red 11, blue 10, green 9
- Random colors on an RGB LED (pins 11, 10 and 9)
- Set the LED on pin 11 from the serial monitor
- A knob on A0 points the servo on pin 3
- Seven-segment digit on pins 4 to 11
- Thermometer: a thermistor on A0
- Tilt switch on pin 3 lights the LED on 13
- Traffic lights on pins 3, 4 and 5
- Two LEDs take turns on pins 4 and 5
- RGB color mixer
- Arduino Uno blink
- Button and LED
- Push button on pin 12 lights the LED on pin 9
- A push button lights an LED, no code
- Push button on pin 12 toggles the LED on pin 9
- Dinosaur game player: light sensor on A0, servo on 9
- Tilt hourglass
- Remote control light switch (IR on 12, servo on 11)
- Joystick lights the way (LEDs on 8 to 11)
- Knob on A0 dims the LED on pin 9
- Photoresistor night light: A0 dims the LED on pin 9
- Light meter: photoresistor on A0, LEDs on pins 5 to 12
- Three knobs mix an RGB LED (pins 11, 10 and 9)
- Starship control panel
- Tilt switch on A5 lights the LED on pin 8
- Tilt switch
- Traffic lights with a crossing button on pin 8
- Two buttons, one LED
- Warm or cool light: a knob blends an RGB LED
- Night light
- Ofrenda candles
- Power module
- Dimmer
- Night light with a light sensor
- A button doorbell with a lamp, no code
- Transistor doorbell: button on 12, buzzer on 9
- Rescue beacon
- Relay on pin 8 through a transistor

Intermediate (53)

- Two Arduino Unos talking over serial
- DHT11 on A0, read with no library
- LCD1602 in 8-bit mode on pins 2 to 12
- DHT11 on pin 3, readings on an LCD
- DC motor on an L293D (pins 5, 3 and 4)
- Radar sweep: ultrasonic on 10 and 11, servo on 12
- Smart trash can: ultrasonic on 8 and 7, servo lid on 9
- Ultrasonic distance on an LCD (TRIG 2, ECHO 3)
- Stepper follows a knob (pins 2 to 5)
- Motor both ways
- Stepper turntable
- LED bar chaser
- Electronic dice
- Joystick bar graph
- Hex digits on a common-anode display (74HC595, pins 11, 12, 13)
- Countdown digit
- Hex digits through a 74HC595 (pins 11, 8 and 12)
- One-digit countdown on a 74HC595 (pins 2, 4 and 3)
- One-digit countdown on a 74HC595 (pins 8, 10 and 9)
- Falling rain on eight LEDs (74HC595, pins 11, 12 and 13)
- Flowing light on a 74HC595 (pins 11, 8 and 12)
- Eight LEDs on a 74HC595 (pins 12, 9 and 11)
- Eight LEDs on a 74HC595 (pins 2, 5 and 4)
- A light runs along eight LEDs on a 74HC595 (pins 11, 12 and 13)
- Serial monitor drives eight LEDs (74HC595)
- Type a digit: serial to a 74HC595 display (pins 11, 8 and 12)
- Cyber dice: seven-segment on pins 2 to 8, button on 9
- Summer fan: four buttons and an L293D (pins 9 and 10)
- Four-digit display on a 74HC595 (pins 8, 10 and 9)
- A knob drives a motor both ways through an L293D
- Relay switched by an L293D (pins 5, 3 and 4)
- Ultrasonic ranging on an LCD
- Thermistor thermometer on an LCD (pins 7 to 12)
- Remote stepper
- Remote stepper, a whole turn a press
- Temperature alarm: thermistor on A0, RGB on 10, 11 and 12
- Thermistor thermometer
- Thermistor on A0, degrees on an LCD (pins 4, 6, 10 to 13)
- Remote-controlled lamps
- Photocell bar graph on a 74HC595
- Photoresistor bar graph on a 74HC595 (pins 9, 12 and 11)
- Digital dice on a 74HC595 (pins 11, 8 and 12)
- Three-speed fan on an L293D (pins 9 and 10)
- Remote-controlled colors: IR on pin 2, RGB on 11, 10 and 9
- Photocell light meter
- Quiz buzzer for three players
- Motor on a transistor
- Servo turnouts with a panel
- Parking sensor
- Remote dimmer: IR on 12, LED on 5, buzzer on 13
- Relay switches a motor
- Spinning zoetrope
- Relay switches a motor: button on 12, relay on 9

Advanced (7)

- Two Arduino Unos as an SPI master and slave
- Stopwatch on a four-digit display
- Stopwatch: four-digit display, digits on 10 to 13
- Four-digit counter
- Four digits from one 74HC595 (pins 11, 12, 13 and 7 to 4)
- 4x4x4 LED cube
- Countdown timer on a four-digit display

Level up

## Add a few parts, unlock more projects

The smallest shopping lists that open the most new projects for the SunFounder Starter Kit for Arduino Uno R3.

### Add Piezo speaker

Unlocks 22 more projects:

- Passive buzzer scale on pin 12
- Passive buzzer module on pin 3
- Passive buzzer on pin 8
- Siren on a passive buzzer (pin 9)
- Twinkle, Twinkle, Little Star on a passive buzzer (pin 9)
- Digital piano
- and 16 more

### Add Character LCD with I2C backpack and Piezo speaker

Unlocks 37 more projects:

- I2C LCD1602: find its address, then say hello
- Passive buzzer scale on pin 12
- Passive buzzer module on pin 3
- Passive buzzer on pin 8
- Siren on a passive buzzer (pin 9)
- Twinkle, Twinkle, Little Star on a passive buzzer (pin 9)
- and 31 more

### Add Character LCD with I2C backpack, Piezo speaker and Addressable RGB LEDs

Unlocks 50 more projects:

- I2C LCD1602: find its address, then say hello
- Passive buzzer scale on pin 12
- Passive buzzer module on pin 3
- Passive buzzer on pin 8
- Siren on a passive buzzer (pin 9)
- Twinkle, Twinkle, Little Star on a passive buzzer (pin 9)
- and 44 more

Two kits

## Projects that combine two kits

Own another kit as well? These need parts from both boxes, and neither can build them alone.

### With the Freenove Ultimate Starter Kit for Raspberry Pi Pico

72 projects:

- I2C LCD1602: find its address, then say hello
- Keypad on pins 11 to 4
- Membrane keypad on pins 9 to 2
- MPU-6050 readings over I2C
- Passive buzzer scale on pin 12
- and 67 more

### With the Keyestudio 37 in 1 Sensor Kit

67 projects:

- Bluetooth chat
- Dusk switch
- Alcohol sensor on A0
- Ambient light sensor on A0
- Button module on pin 3 lights the LED on 13
- and 62 more

### With the Freenove Ultimate Starter Kit for ESP32-WROVER

66 projects:

- I2C LCD1602: find its address, then say hello
- Keypad on pins 11 to 4
- Membrane keypad on pins 9 to 2
- MPU-6050 readings over I2C
- Passive buzzer scale on pin 12
- and 61 more

### With the SunFounder Universal Maker Sensor Kit

56 projects:

- Digital piano
- ESP-01 blink
- Battery level indicator
- Crosswalk
- Dreidel spinner
- and 51 more

Free course

## Learn it as a course, step by step

The same lessons as a guided course: chapters, projects and every step checked by the simulator.

Starter kit companion: the 24-lesson kit

24 lessons, 2 of them from this kit

Starter kit companion: the 33-lesson kit

33 lessons, 2 of them from this kit

In the box

## The kit’s parts, and what plays them here

The parts in the SunFounder Starter Kit for Arduino Uno R3, by the names its maker gives them. Each one is in the editor’s parts panel.

- Mega 2560 Controller Board Arduino Uno R3 SunFounder’s list, and the packing list on its store page, name a Mega 2560, though the kit is sold for the Uno R3; the lessons here run on the Uno.
- Breadboard Full-size breadboard
- LED (Red, Green, Yellow, White and Blue) LED
- RGB LED RGB LED
- Resistors (10, 100, 220 and 330 ohm, 1k, 2k, 5.1k, 10k and 100k ohm, 1M ohm) Resistor
- Button (small) Pushbutton
- Potentiometer Potentiometer
- Tilt Switch Tilt switch
- Active Buzzer Buzzer
- Photoresistor Light sensor
- Thermistor Thermistor, 10k NTC
- Humiture Sensor Temperature and humidity, DHT22 A DHT11 module; set to the DHT11 model on the canvas.
- Joystick PS2 Thumb stick
- Infrared Receiver Infrared receiver, VS1838B
- Remote Control Infrared remote, 21 buttons
- Ultrasonic Sensor Module Ultrasonic ranger
- 16*2 LCD Character Display Character LCD, 16x2
- One-digit Segment Display Seven segment display
- 4-digit 7-segment Display Four-digit seven segment, multiplexed
- 74HC595 74HC595 shift register
- Servo Motor (SG90) Hobby servo
- Stepper Motor and Stepper Motor Driver Stepper motor, 28BYJ-48 with ULN2003
- L293d Motor driver, L293D
- Small Motor DC motor
- Fan The blade for the small motor; nothing to place.
- 5v Relay DPDT relay
- NPN Transistor (S8050) Transistor (NPN or PNP) Set to S8050.
- 1N4007 Diode Set to 1N4007.
- Capacitor Ceramic 100nF Capacitor
- power supply module Breadboard power supply, MB102
- 9V Battery Clip Connector Battery: AA, coin cell, LiPo The battery is set to 9 V; the kit has the clip, not the battery.
- USB Cable The editor connects the board for you.
- Jumper Wire and Dupont Wire Drawn as wires between pins; nothing to place.

Parts list read from SunFounder’s components list. An item with no part beside it has no match in the editor yet.

For the manual

## A link and a QR code for this page

Print either one beside a lesson, or tape it inside the box lid. Both open this page.

mokxi.com/k/sunfounder-starter

The code is black on white with a quiet border, so it prints and scans at any size from 2 cm up.
Download the QR code (SVG)
Make kits? See what we offer kit makers.

FAQ

## Questions about this page

Is this made by SunFounder?

No. Mokxi is independent and is not affiliated with SunFounder. The page follows the kit’s lessons so you can use the two side by side; the circuits, sketches and explanations are Mokxi’s own.

Do I need the kit?

No. Every lesson that runs here runs in the browser, so you can try them before you buy a kit, or keep going while a part is missing or broken.

Is the code the same as in my manual?

The pins and the parts are the same, and the sketches use the same libraries where the kit does. The code itself is written for this page, with comments that explain each step, so it will not match the manual line for line.

What do "with a change" and "coming soon" mean?

A lesson marked "with a change" runs, but something differs from the kit, and the note under it says exactly what. "Coming soon" means we cannot simulate that lesson yet, and the note says why. We do not mark a lesson as running unless it does.

Is it free?

Yes. Every lesson on this page opens with no account. A free account saves your own copies of the circuits.

Keep going

## Other kits

Companion pages for more starter kits.

ELEGOO UNO R3 Super Starter Kit

25 lessons, 24 run in the browser

ELEGOO UNO R3 Most Complete Starter Kit

48 lessons, 44 run in the browser

Arduino Starter Kit

15 lessons, 15 run in the browser

Freenove Ultimate Starter Kit

42 lessons, 42 run in the browser

ELEGOO UNO R3 Basic Starter Kit

11 lessons, 10 run in the browser

SunFounder Inventor Lab Kit

34 lessons, 33 run in the browser

Keyestudio 37 in 1 Sensor Kit

37 lessons, 37 run in the browser

REXQualis UNO R3 Super Starter Kit

22 lessons, 21 run in the browser

LAFVIN Super Starter Kit

28 lessons, 27 run in the browser

Freenove Ultimate Starter Kit for ESP32-WROVER

54 lessons, 44 run in the browser

SunFounder Kepler Kit for Raspberry Pi Pico W

63 lessons, 48 run in the browser

Freenove Ultimate Starter Kit for Raspberry Pi Pico

56 lessons, 50 run in the browser

keyestudio Super Starter Kit

Projects you can build with its parts

Vilros Arduino Uno 3 Ultimate Starter Kit

Projects you can build with its parts

SunFounder Universal Maker Sensor Kit

Projects you can build with its parts

SunFounder ESP32 Ultimate Starter Kit

Projects you can build with its parts

Adafruit MetroX Classic Kit

Projects you can build with its parts

MonkMakes Electronics Kit 1 for Raspberry Pi Pico

Projects you can build with its parts

Kitronik Discovery Kit for Raspberry Pi Pico

Projects you can build with its parts

Kitronik Inventor’s Kit for the Raspberry Pi Pico

Projects you can build with its parts

Keyestudio ESP32 Learning Kit Ultimate Edition

Projects you can build with its parts

## Start at lesson one

Every project opens in the editor with no account and nothing to install. Run it, change a number, run it again.

See the lessons
