Source: https://mokxi.com/kits/companion/elegoo-uno-r3-super-starter-kit
Updated: 2026-11-07

Kits / Kit companions
Kit companion

# ELEGOO UNO R3 Super Starter Kit: every lesson, simulated

Every lesson of the kit’s tutorial, in its order, as a circuit you can run in your browser with the same parts on the same pins. Open a lesson next to your manual, see it working, then wire it on your bench.

Open the first lesson Find your lesson What else it can build

Not affiliated with ELEGOO. Lesson titles are referenced so you can follow along.

Lesson by lesson

## Every lesson in the kit’s order

Lesson numbers and titles follow tutorial V1.0 (2019.09.17), from the download dated 2023.05.05. Each circuit uses the kit’s parts on the pins the lesson uses.

24 of the 24 lessons with a circuit run here, 1 setup lesson needs no circuit.

0

### Installing IDE

No circuit

Installing the Arduino IDE. Nothing to install here: the editor and the compiler run in the browser.

1

### Add Libraries and Open Serial Monitor

Runs here

Printing from the board to the serial monitor. The libraries the kit uses are already built in.

Open the guided lesson

2

### Blink

Runs here

The board’s own LED on pin 13, on for half a second and off for half a second.

Open in the editor Arduino Uno blink

3

### LED

Runs here

An LED and a resistor on the 5 V pin, no code. Swap 220 ohm for 1k or 10k and see it dim.

Open in the editor An LED on the 5 V pin

4

### RGB LED

Runs here

Red on pin 6, green on 5, blue on 3: analogWrite fades one color into the next.

Open in the editor RGB fade on pins 6, 5 and 3

5

### Digital Inputs

Runs here

Two buttons with the internal pull-ups: one on pin 9 turns the LED on pin 5 on, one on pin 8 turns it off.

Open in the editor Two buttons, one LED

6

### Active buzzer

Runs here

An active buzzer on pin 12 sounds while the pin is HIGH: quick beeps, then slow ones.

Open in the editor Active buzzer

7

### Passive Buzzer

Runs here

A passive buzzer on pin 8 plays a scale with tone().

Open in the editor Passive buzzer on pin 8

8

### Tilt Ball Switch

Runs here

A ball switch on pin 2 with the pull-up on: tip it and the LED on pin 13 lights.

Open in the editor Tilt switch

9

### Servo

Runs here

An SG90 on pin 9 jumps to 0, 90 and 180 degrees, then sweeps back.

Open in the editor Servo sweep

10

### Ultrasonic Sensor Module

Runs here

An HC-SR04 with TRIG on 12 and ECHO on 11, read with the SR04 library, prints centimeters.

Open in the editor Ultrasonic distance on pins 12 and 11

11

### DHT11 Temperature and Humidity Sensor

Runs here

A DHT11 on pin 2 reports temperature and humidity every two seconds.

Open in the editor DHT11 temperature and humidity

12

### Analog Joystick Module

Runs here

X on A0, Y on A1 and the press switch on pin 2, printed to the serial monitor.

Open in the editor Joystick on A0, A1 and pin 2

13

### IR Receiver Module

Runs here

An IR receiver on pin 11 decodes the remote’s buttons.

Open in the editor IR decoder

14

### LCD Display

Runs here

A 16x2 LCD on pins 7 to 12 says hello and counts the seconds.

The contrast knob is left out: the simulated display is always readable, so V0 goes to ground.

Open in the editor LCD1602 on pins 7 to 12

15

### Thermometer

Runs here

A thermistor on A0 and the beta equation, read out in degrees on the LCD.

The contrast knob is left out: the simulated display is always readable, so V0 goes to ground.

Open in the editor Thermistor thermometer on an LCD (pins 7 to 12)

16

### Eight LED with 74HC595

Runs here

Eight LEDs from three pins through a shift register: data 12, clock 9, latch 11.

Open in the editor Eight LEDs on a 74HC595 (pins 12, 9 and 11)

17

### The Serial Monitor

Runs here

Type 0 to 7 into the serial monitor to light that LED on the shift register, or x to clear.

Open in the editor Serial monitor drives eight LEDs (74HC595)

18

### Photocell

Runs here

A photocell on A0 sets how many of the eight LEDs light.

Open in the editor Photocell bar graph on a 74HC595

19

### 74HC595 And Segment Display

Runs here

One seven-segment digit through a 74HC595 on pins 2, 4 and 3, counting down from 9.

One 220 ohm resistor on the common pin stands in for a resistor on every segment.

Open in the editor One-digit countdown on a 74HC595 (pins 2, 4 and 3)

20

### Four Digital Seven Segment Display

Runs here

A four-digit display on a 74HC595 (pins 8, 10 and 9), every digit on, stepping through 0 to F.

Open in the editor Four-digit display on a 74HC595 (pins 8, 10 and 9)

21

### DC Motors

Runs here

An L293D runs a motor: speed on pin 5, direction on pins 3 and 4.

The motor runs from the Uno’s 5 V here; on the bench the lesson powers it from the breadboard power module.

Open in the editor DC motor on an L293D (pins 5, 3 and 4)

22

### Relay

Runs here

The L293D drives a relay’s coil, and the relay switches the motor on and off.

The motor runs from the Uno’s 5 V here; on the bench the lesson powers it from the breadboard power module.

Open in the editor Relay switched by an L293D (pins 5, 3 and 4)

23

### Stepper Motor

Runs here

A 28BYJ-48 on its ULN2003 board, pins 8 to 11, one turn each way.

Open in the editor Stepper motor on pins 8 to 11

24

### Controlling Stepper Motor With Remote

Runs here

VOL+ and VOL- on the remote turn the stepper, with the receiver on pin 12.

Open in the editor Remote stepper

Lesson list and pins read from ELEGOO’s tutorial download page. The explanations on this page are our own.

Learning path

## Everything the ELEGOO UNO R3 Super Starter Kit can build

163 projects use only the parts in this box, ordered from a first blink to the hardest.

Beginner (94)

- EEPROM: memory that survives a reset
- Serial echo: the board repeats what you type
- Active buzzer
- Active buzzer module on pin 3
- DHT11 temperature and humidity
- DHT11 module on pin 4
- DHT11 temperature and humidity on pin 10
- Joystick on A0, A1 and pin 2
- Joystick module: A0, A1 and pin 3
- Joystick on A0, A1 and pin 8
- LCD1602 on pins 4, 6 and 10 to 13
- LCD1602 on pins 7 to 12
- LCD1602 hello
- Morse code on an active buzzer (pin 9)
- Passive buzzer scale on pin 12
- Passive buzzer module on pin 3
- Passive buzzer on pin 8
- Pomodoro timer on an active buzzer (pin 9)
- Servo sweep
- Servo sweep on pin 10
- Servo sweep on pin 3
- Siren on a passive buzzer (pin 9)
- Ultrasonic distance on pins 12 and 11
- Ultrasonic sensor on 8 and 7, the LED on 13 when out of range
- Stepper motor on pins 8 to 11
- Twinkle, Twinkle, Little Star on a passive buzzer (pin 9)
- Read a knob
- Digital piano
- Fade an LED
- First blink
- IR decoder
- Blink an LED on pin 13, once a second
- Blink an LED on pin 3
- Blink an LED on pin 8
- Blink an LED on pin 9
- Breathing LED on pin 5
- Button on pin 12 lights the LED on pin 13
- Answer ball
- Flowing lights on pins 2 to 9
- IR remote codes on pin 12
- IR receiver module on pin 11
- IR receiver on pin 2
- LED module on pin 7, blinking
- An LED on the 5 V pin
- Mood dial
- Four brightnesses from PWM: pins 5, 6, 9 and 10
- RGB colors on pins 11, 10 and 9
- RGB LED on pins 3, 5 and 6
- RGB fade on pins 6, 5 and 3
- RGB LED module: red 11, blue 10, green 9
- Random colors on an RGB LED (pins 11, 10 and 9)
- Set the LED on pin 11 from the serial monitor
- A knob on A0 points the servo on pin 3
- Seven-segment digit on pins 4 to 11
- Thermometer: a thermistor on A0
- Tilt switch on pin 3 lights the LED on 13
- Traffic lights on pins 3, 4 and 5
- Two LEDs take turns on pins 4 and 5
- RGB color mixer
- Arduino Uno blink
- Button and LED
- Grabbing candy bowl
- Passive buzzer alarm on pin 9, through a transistor
- Push button on pin 12 lights the LED on pin 9
- A push button lights an LED, no code
- Push button on pin 12 toggles the LED on pin 9
- Dinosaur game player: light sensor on A0, servo on 9
- Doorbell: button on pin 2, buzzer on pin 8
- Tilt hourglass
- Remote control light switch (IR on 12, servo on 11)
- Joystick lights the way (LEDs on 8 to 11)
- Four-key keyboard
- Knob on A0 dims the LED on pin 9
- Photoresistor night light: A0 dims the LED on pin 9
- Light meter: photoresistor on A0, LEDs on pins 5 to 12
- Three knobs mix an RGB LED (pins 11, 10 and 9)
- Starship control panel
- Tilt switch on A5 lights the LED on pin 8
- Tilt switch
- Traffic lights with a crossing button on pin 8
- Two buttons, one LED
- Warm or cool light: a knob blends an RGB LED
- Night light
- Ofrenda candles
- Piezo melody
- Power module
- Dimmer
- Night light with a light sensor
- A button doorbell with a lamp, no code
- Transistor doorbell: button on 12, buzzer on 9
- Metronome
- Police lights and siren
- Rescue beacon
- Relay on pin 8 through a transistor

Intermediate (62)

- Two Arduino Unos talking over serial
- DHT11 on A0, read with no library
- LCD1602 in 8-bit mode on pins 2 to 12
- DHT11 on pin 3, readings on an LCD
- DC motor on an L293D (pins 5, 3 and 4)
- Radar sweep: ultrasonic on 10 and 11, servo on 12
- Smart trash can: ultrasonic on 8 and 7, servo lid on 9
- Ultrasonic distance on an LCD (TRIG 2, ECHO 3)
- Stepper follows a knob (pins 2 to 5)
- Motor both ways
- Stepper turntable
- Arpeggiator
- LED bar chaser
- Electronic dice
- Joystick bar graph
- Hex digits on a common-anode display (74HC595, pins 11, 12, 13)
- Countdown digit
- Hex digits through a 74HC595 (pins 11, 8 and 12)
- One-digit countdown on a 74HC595 (pins 2, 4 and 3)
- One-digit countdown on a 74HC595 (pins 8, 10 and 9)
- Falling rain on eight LEDs (74HC595, pins 11, 12 and 13)
- Flowing light on a 74HC595 (pins 11, 8 and 12)
- Eight LEDs on a 74HC595 (pins 12, 9 and 11)
- Eight LEDs on a 74HC595 (pins 2, 5 and 4)
- A light runs along eight LEDs on a 74HC595 (pins 11, 12 and 13)
- Serial monitor drives eight LEDs (74HC595)
- Type a digit: serial to a 74HC595 display (pins 11, 8 and 12)
- Cyber dice: seven-segment on pins 2 to 8, button on 9
- Summer fan: four buttons and an L293D (pins 9 and 10)
- Four-digit display on a 74HC595 (pins 8, 10 and 9)
- A knob drives a motor both ways through an L293D
- Relay switched by an L293D (pins 5, 3 and 4)
- Ultrasonic ranging on an LCD
- Thermistor thermometer on an LCD (pins 7 to 12)
- Remote stepper
- Remote stepper, a whole turn a press
- Temperature alarm: thermistor on A0, RGB on 10, 11 and 12
- Thermistor thermometer
- Thermistor on A0, degrees on an LCD (pins 4, 6, 10 to 13)
- Remote-controlled lamps
- Photocell bar graph on a 74HC595
- Photoresistor bar graph on a 74HC595 (pins 9, 12 and 11)
- Digital dice on a 74HC595 (pins 11, 8 and 12)
- Three-speed fan on an L293D (pins 9 and 10)
- Remote-controlled colors: IR on pin 2, RGB on 11, 10 and 9
- Photocell light meter
- Quiz buzzer for three players
- Looper
- Motor on a transistor
- Servo turnouts with a panel
- Reaction duel
- Parking sensor
- Tap-tempo metronome
- ADSR synth
- Reaction timer
- Ringtone player
- Remote dimmer: IR on 12, LED on 5, buzzer on 13
- Memory math game on an LCD and an IR remote
- Relay switches a motor
- Spinning zoetrope
- Lion dance head
- Relay switches a motor: button on 12, relay on 9

Advanced (7)

- Two Arduino Unos as an SPI master and slave
- Stopwatch on a four-digit display
- Stopwatch: four-digit display, digits on 10 to 13
- Four-digit counter
- Four digits from one 74HC595 (pins 11, 12, 13 and 7 to 4)
- 4x4x4 LED cube
- Countdown timer on a four-digit display

Level up

## Add a few parts, unlock more projects

The smallest shopping lists that open the most new projects for the ELEGOO UNO R3 Super Starter Kit.

### Add Character LCD with I2C backpack

Unlocks 15 more projects:

- I2C LCD1602: find its address, then say hello
- Dreidel spinner
- Eid greeting card
- Message display gift
- Red envelope box
- Pi digits on an LCD
- and 9 more

### Add Character LCD with I2C backpack and Addressable RGB LEDs

Unlocks 28 more projects:

- I2C LCD1602: find its address, then say hello
- Diwali diya row
- Dreidel spinner
- Marigold path
- Hanukkah menorah
- Rainbow to the pot of gold
- and 22 more

### Add ili9341, Character LCD with I2C backpack and Addressable RGB LEDs

Unlocks 40 more projects:

- I2C LCD1602: find its address, then say hello
- Diwali diya row
- Dreidel spinner
- Marigold path
- Hanukkah menorah
- Rainbow to the pot of gold
- and 34 more

Two kits

## Projects that combine two kits

Own another kit as well? These need parts from both boxes, and neither can build them alone.

### With the SunFounder Kepler Kit for Raspberry Pi Pico W

60 projects:

- I2C LCD1602: find its address, then say hello
- Keypad on pins 11 to 4
- Membrane keypad on pins 9 to 2
- MPU-6050 readings over I2C
- Motion sensor on pin 3 lights the LED on 13
- and 55 more

### With the Freenove Ultimate Starter Kit for Raspberry Pi Pico

50 projects:

- I2C LCD1602: find its address, then say hello
- Keypad on pins 11 to 4
- Membrane keypad on pins 9 to 2
- MPU-6050 readings over I2C
- Motion sensor on pin 3 lights the LED on 13
- and 45 more

### With the Keyestudio 37 in 1 Sensor Kit

45 projects:

- Bluetooth chat
- Dusk switch
- Alcohol sensor on A0
- Ambient light sensor on A0
- Button module on pin 3 lights the LED on 13
- and 40 more

### With the Freenove Ultimate Starter Kit for ESP32-WROVER

44 projects:

- I2C LCD1602: find its address, then say hello
- Keypad on pins 11 to 4
- Membrane keypad on pins 9 to 2
- MPU-6050 readings over I2C
- Motion sensor on pin 3 lights the LED on 13
- and 39 more

Free course

## Learn it as a course, step by step

The same lessons as a guided course: chapters, projects and every step checked by the simulator.

Starter kit companion: the 24-lesson kit

24 lessons, 6 of them from this kit

Starter kit companion: the 33-lesson kit

33 lessons, 6 of them from this kit

In the box

## The kit’s parts, and what plays them here

The parts in the ELEGOO UNO R3 Super Starter Kit, by the names its maker gives them. Each one is in the editor’s parts panel.

- Uno R3 Controller Board Arduino Uno R3
- 830 Tie-Points Breadboard Full-size breadboard
- LED LED
- RGB RGB LED
- Resistor Resistor
- Button (Small) Pushbutton
- Potentiometer Potentiometer
- Tilt Ball Switch Tilt switch
- Active Buzzer Buzzer
- Passive Buzzer Piezo speaker
- Servo Motor (SG90) Hobby servo
- Ultrasonic Sensor Ultrasonic ranger
- DHT11 Temperature and Humidity Module Temperature and humidity, DHT22 Set to the DHT11 model on the canvas.
- Joystick Module Thumb stick
- IR Receiver Module Infrared receiver, VS1838B
- Remote Infrared remote, 21 buttons
- LCD 1602 Module (with pin header) Character LCD, 16x2
- Thermistor Thermistor, 10k NTC
- 74HC595 IC 74HC595 shift register
- Photoresistor (Photocell) Light sensor
- 1 digit 7-segment Display Seven segment display
- 4 digit 7-segment Display Four-digit seven segment, multiplexed
- L293D Motor driver, L293D
- Fan Blade and 3-6V DC Motor (with wire) DC motor
- NPN Transistor PN2222 Transistor (NPN or PNP) Set to 2N2222, the same transistor.
- Diode Rectifier Diode
- 5V Relay DPDT relay
- Stepper Motor and ULN2003 Stepper Motor Driver Module Stepper motor, 28BYJ-48 with ULN2003
- Power Supply Module Breadboard power supply, MB102
- 9V Battery with Snap-on Connector Clip Battery: AA, coin cell, LiPo The battery is set to 9 V.
- Prototype Expansion Module No model of the prototype shield yet; no lesson uses it.
- USB Cable The editor connects the board for you.
- Breadboard Jumper Wire and Female-to-male Dupont wire Drawn as wires between pins; nothing to place.

Parts list read from ELEGOO’s tutorial PDF (a copy hosted by uastem.com). An item with no part beside it has no match in the editor yet.

For the manual

## A link and a QR code for this page

Print either one beside a lesson, or tape it inside the box lid. Both open this page.

mokxi.com/k/elegoo-super

The code is black on white with a quiet border, so it prints and scans at any size from 2 cm up.
Download the QR code (SVG)
Make kits? See what we offer kit makers.

FAQ

## Questions about this page

Is this made by ELEGOO?

No. Mokxi is independent and is not affiliated with ELEGOO. The page follows the kit’s lessons so you can use the two side by side; the circuits, sketches and explanations are Mokxi’s own.

Do I need the kit?

No. Every lesson that runs here runs in the browser, so you can try them before you buy a kit, or keep going while a part is missing or broken.

Is the code the same as in my manual?

The pins and the parts are the same, and the sketches use the same libraries where the kit does. The code itself is written for this page, with comments that explain each step, so it will not match the manual line for line.

What do "with a change" and "coming soon" mean?

A lesson marked "with a change" runs, but something differs from the kit, and the note under it says exactly what. "Coming soon" means we cannot simulate that lesson yet, and the note says why. We do not mark a lesson as running unless it does.

Is it free?

Yes. Every lesson on this page opens with no account. A free account saves your own copies of the circuits.

Keep going

## Other kits

Companion pages for more starter kits.

ELEGOO UNO R3 Most Complete Starter Kit

48 lessons, 44 run in the browser

Arduino Starter Kit

15 lessons, 15 run in the browser

Freenove Ultimate Starter Kit

42 lessons, 42 run in the browser

ELEGOO UNO R3 Basic Starter Kit

11 lessons, 10 run in the browser

SunFounder Starter Kit for Arduino Uno R3

23 lessons, 23 run in the browser

SunFounder Inventor Lab Kit

34 lessons, 33 run in the browser

Keyestudio 37 in 1 Sensor Kit

37 lessons, 37 run in the browser

REXQualis UNO R3 Super Starter Kit

22 lessons, 21 run in the browser

LAFVIN Super Starter Kit

28 lessons, 27 run in the browser

Freenove Ultimate Starter Kit for ESP32-WROVER

54 lessons, 44 run in the browser

SunFounder Kepler Kit for Raspberry Pi Pico W

63 lessons, 48 run in the browser

Freenove Ultimate Starter Kit for Raspberry Pi Pico

56 lessons, 50 run in the browser

keyestudio Super Starter Kit

Projects you can build with its parts

Vilros Arduino Uno 3 Ultimate Starter Kit

Projects you can build with its parts

SunFounder Universal Maker Sensor Kit

Projects you can build with its parts

SunFounder ESP32 Ultimate Starter Kit

Projects you can build with its parts

Adafruit MetroX Classic Kit

Projects you can build with its parts

MonkMakes Electronics Kit 1 for Raspberry Pi Pico

Projects you can build with its parts

Kitronik Discovery Kit for Raspberry Pi Pico

Projects you can build with its parts

Kitronik Inventor’s Kit for the Raspberry Pi Pico

Projects you can build with its parts

Keyestudio ESP32 Learning Kit Ultimate Edition

Projects you can build with its parts

## Start at lesson one

Every project opens in the editor with no account and nothing to install. Run it, change a number, run it again.

See the lessons
