Source: https://mokxi.com/kits/companion/elegoo-uno-r3-most-complete-starter-kit
Updated: 2026-11-07

Kits / Kit companions
Kit companion

# ELEGOO UNO R3 Most Complete Starter Kit: every lesson, simulated

The four parts of the kit’s V2.0 tutorial, lesson by lesson, each one a circuit that runs in your browser with the kit’s parts on the kit’s pins. Use it beside your manual, or to keep going while a part is missing.

Open the first lesson Find your lesson What else it can build

Not affiliated with ELEGOO. Lesson titles are referenced so you can follow along.

Lesson by lesson

## Every lesson in the kit’s order

Lesson numbers and titles follow tutorial V2.0, from the download dated 2023.05.08 (older boxes ship the V1.0 tutorial, which numbers its lessons differently). Each circuit uses the kit’s parts on the pins the lesson uses.

44 of the 44 lessons with a circuit run here, 9 of them with a change we name, 4 setup lessons need no circuit.

1.1

### Packing List

No circuit

What is in the box. Every part the lessons use is in the editor’s parts panel.

1.2

### First Look Arduino

No circuit

A tour of the Uno board. Hover any pin on the canvas to see its name.

1.3

### For Windows Setting up development environment

No circuit

Installing the IDE and drivers on Windows. Not needed here: everything runs in the browser.

1.4

### For Mac and Ubuntu Building a Developed Environment

No circuit

The same setup on a Mac or on Linux. Not needed here either.

1.5

### Blink and Add Libraries

Runs here

The LED on pin 13 blinking once a second. The kit’s libraries are already built in.

Open in the editor Arduino Uno blink

2.1

### LED

Runs here

An LED and a resistor on the 5 V pin, no code. Try 1k and 10k in place of 220 ohm.

Open in the editor An LED on the 5 V pin

2.2

### RGB LED

Runs here

Red on pin 6, green on 5, blue on 3, fading from color to color.

Open in the editor RGB fade on pins 6, 5 and 3

2.3

### Digital Inputs

Runs here

A button on pin 9 turns the LED on pin 5 on, a button on pin 8 turns it off.

Open in the editor Two buttons, one LED

2.4

### Serial Monitor

Runs here

Talking to the board through the serial monitor, the tool you will use in every later lesson.

Open the guided lesson

2.5

### Active Buzzer

Runs here

An active buzzer on pin 12, beeping fast and then slow.

Open in the editor Active buzzer

2.6

### Passive Buzzer

Runs here

A passive buzzer on pin 8 plays a scale with tone().

Open in the editor Passive buzzer on pin 8

2.7

### Tilt Ball Switch

Runs here

Tip the ball switch on pin 2 and the LED on pin 13 lights.

Open in the editor Tilt switch

2.8

### Servo

Runs here

A micro servo on pin 9 moving to set angles and sweeping back.

Open in the editor Servo sweep

2.9

### Ultrasonic Sensor Module

Runs here

An HC-SR04, TRIG on 12 and ECHO on 11, measuring distance in centimeters.

Open in the editor Ultrasonic distance on pins 12 and 11

2.10

### Membrane Switch Module

Runs here

A 4x4 keypad, rows on pins 9 to 6 and columns on 5 to 2, printing each key.

Open in the editor Membrane keypad on pins 9 to 2

2.11

### DHT11 Temperature and Humidity Sensor

Runs here

A DHT11 on pin 2 reading temperature and humidity.

Open in the editor DHT11 temperature and humidity

2.12

### Analog Joystick Module

Runs here

X on A0, Y on A1, the switch on pin 2.

Open in the editor Joystick on A0, A1 and pin 2

2.13

### IR Receiver Module

Runs here

An IR receiver on pin 11 decoding the remote.

Open in the editor IR decoder

2.14

### MAX7219 LED Dot Matrix Module

Runs here

An 8x8 matrix on a MAX7219, DIN 12, CLK 10 and CS 11, drawing faces.

Open in the editor MAX7219 8x8 matrix (pins 12, 10 and 11)

2.15

### Gyro (MPU-6050 Module)

Runs here

An MPU-6050 on the I2C pins, printing its raw acceleration and rotation.

Some boxes ship a QMI-8658 board for this lesson instead; that chip is not simulated yet.

Open in the editor MPU-6050 readings over I2C

2.16

### HC-SR501 PIR Sensor

Runs here

A motion sensor on pin 7 lights the LED on pin 13.

Open in the editor PIR motion light

2.17

### Water Level Detection Sensor Module

Runs here

A water level sensor on A0, sorted into dry, low, half and full.

Open in the editor Water level sensor

2.18

### Real Time Clock Module

Runs here

A DS1307 clock on A4 and A5 keeping the date and time.

Open in the editor Real-time clock

2.19

### Sound Sensor Module

Runs here

A sound sensor with its analog output on A0 and its digital output on pin 3.

Open in the editor Sound sensor on A0 and pin 3

2.20

### RC522 RFID Module

Runs here

An RC522 reader, SS on 10 and RST on 9, printing each card’s ID.

Open in the editor RC522 RFID reader (SS 10, RST 9)

2.21

### LCD Display

Runs here

A 16x2 LCD on pins 7 to 12.

The contrast knob is left out: the simulated display is always readable, so V0 goes to ground.

Open in the editor LCD1602 on pins 7 to 12

2.22

### Eight LED with 74HC595

Runs here

Eight LEDs on a shift register: data 12, clock 9, latch 11.

Open in the editor Eight LEDs on a 74HC595 (pins 12, 9 and 11)

2.23

### DC Motors

Runs here

An L293D on pins 5, 3 and 4 driving a motor both ways.

The motor runs from the Uno’s 5 V here; on the bench the lesson powers it from the breadboard power module.

Open in the editor DC motor on an L293D (pins 5, 3 and 4)

2.24

### Stepper Motor

Runs here

A 28BYJ-48 on pins 8 to 11, one turn each way.

Open in the editor Stepper motor on pins 8 to 11

2.25

### EEPROM

Runs here

Saving numbers in the Uno’s EEPROM so they survive a reset.

Open in the editor EEPROM: memory that survives a reset

3.1

### Thermometer

Runs here

A thermistor on A0, the temperature on the LCD.

The contrast knob is left out: the simulated display is always readable, so V0 goes to ground.

Open in the editor Thermistor thermometer on an LCD (pins 7 to 12)

3.2

### 74HC595 And Segment Display

Runs here

A digit counting down through a 74HC595 on pins 2, 4 and 3.

One 220 ohm resistor on the common pin stands in for a resistor on every segment.

Open in the editor One-digit countdown on a 74HC595 (pins 2, 4 and 3)

3.3

### The Serial Monitor

Runs here

Lighting the shift register’s LEDs by typing into the serial monitor.

Open in the editor Serial monitor drives eight LEDs (74HC595)

3.4

### Photocell

Runs here

A photocell on A0 drives a bar of eight LEDs.

Open in the editor Photocell bar graph on a 74HC595

3.5

### Four Digit Seven Segment Display

Runs here

Four digits on a 74HC595, pins 8, 10 and 9.

Open in the editor Four-digit display on a 74HC595 (pins 8, 10 and 9)

3.6

### Relay

Runs here

A relay driven by the L293D switches the motor.

The motor runs from the Uno’s 5 V here; on the bench the lesson powers it from the breadboard power module.

Open in the editor Relay switched by an L293D (pins 5, 3 and 4)

3.7

### Controlling a Stepper Motor With Remote

Runs here

The remote’s VOL+ and VOL- turn the stepper.

Open in the editor Remote stepper

3.8

### Controlling a Stepper Motor With Rotary Encoder

Runs here

A rotary encoder on pins 2, 3 and 4 steers the stepper click for click.

Open in the editor Knob stepper

3.9

### Creating Timer

Runs here

A countdown timer on a four-digit display, set with buttons on A3 and 6 and started with A1. An S8050 transistor switches the LED on A0.

The tutorial’s drawing labels the transistor PN2222; its text and parts list say 8050, which is what is used here.

Open in the editor Countdown timer on a four-digit display

4.1

### Dice

Runs, with a change

Shake the tilt switch and an 8x8 matrix rolls a die.

The kit builds this on its ALL IN ONE Sensor Shield. Mokxi has no model of that shield yet, so the same parts are wired on a breadboard to the same pins the shield uses.

Open in the editor Tilt dice on an 8x8 matrix

4.2

### Greedy Snake

Runs, with a change

A snake on the 8x8 matrix, steered by tipping the MPU-6050: eat the blinking dot to grow.

The kit builds this on its ALL IN ONE Sensor Shield. Mokxi has no model of that shield yet, so the same parts are wired on a breadboard to the same pins the shield uses.

Open in the editor Tilt snake on an 8x8 matrix

4.3

### Memory Arithmetic Game

Runs, with a change

A number or a sum flashes on the LCD for two seconds; key in the answer on the IR remote. Five questions a round.

The kit builds this on its ALL IN ONE Sensor Shield. Mokxi has no model of that shield yet, so the same parts are wired on a breadboard to the same pins the shield uses. The kit remote’s VOL-, EQ and ST/REPT keys send the same codes as the +, 100+ and 200+ keys on the simulated one.

Open in the editor Memory math game on an LCD and an IR remote

4.4

### Fruit Forecast

Runs, with a change

Tip the board to slide a cup along the matrix and catch the falling beans; the RGB LED counts your lives.

The kit builds this on its ALL IN ONE Sensor Shield. Mokxi has no model of that shield yet, so the same parts are wired on a breadboard to the same pins the shield uses.

Open in the editor Catch the beans: a tilt game on an 8x8 matrix

4.5

### Multifunctional alarm clock

Runs, with a change

The time, the date, the temperature and humidity on the four-digit display, with a kitchen timer and an alarm saved in EEPROM.

The kit builds this on its ALL IN ONE Sensor Shield. Mokxi has no model of that shield yet, so the same parts are wired on a breadboard to the same pins the shield uses. The fourth button (pin 10) sits beside the board; the sketch reads the buttons in loop() rather than with pin-change interrupts.

Open in the editor Alarm clock with a timer on a four-digit display

4.6

### Ultrasonic Ranging

Runs, with a change

Hold a button and the distance in front of the sensor appears on the LCD.

The kit builds this on its ALL IN ONE Sensor Shield. Mokxi has no model of that shield yet, so the same parts are wired on a breadboard to the same pins the shield uses.

Open in the editor Ultrasonic ranging on an LCD

4.7

### RFID Time Clock

Runs, with a change

Enroll cards with a button, then swipe one to clock in: the LCD names the person and the serial monitor logs the time.

The kit builds this on its ALL IN ONE Sensor Shield. Mokxi has no model of that shield yet, so the same parts are wired on a breadboard to the same pins the shield uses. The reader’s RST is on A1, as in the lesson’s sketch (the shield’s label says D9).

Open in the editor RFID time clock with an LCD and a DS1307

4.8

### Infrared Remote Switch Light

Runs, with a change

A servo arm flips a light switch when you press 1 or 2 on the remote.

The kit builds this on its ALL IN ONE Sensor Shield. Mokxi has no model of that shield yet, so the same parts are wired on a breadboard to the same pins the shield uses.

Open in the editor Remote control light switch (IR on 12, servo on 11)

4.9

### Body-sensing Nightlight

Runs, with a change

A motion sensor turns on an RGB night light for 20 seconds.

The kit builds this on its ALL IN ONE Sensor Shield. Mokxi has no model of that shield yet, so the same parts are wired on a breadboard to the same pins the shield uses.

Open in the editor Motion night light (PIR on 12, RGB on 5, 6 and 9)

Lesson list and pins read from ELEGOO’s tutorial download page. The explanations on this page are our own.

Learning path

## Everything the ELEGOO UNO R3 Most Complete Starter Kit can build

199 projects use only the parts in this box, ordered from a first blink to the hardest.

Beginner (114)

- EEPROM: memory that survives a reset
- Serial echo: the board repeats what you type
- Active buzzer
- Active buzzer module on pin 3
- DHT11 temperature and humidity
- DHT11 module on pin 4
- DHT11 temperature and humidity on pin 10
- Joystick on A0, A1 and pin 2
- Joystick module: A0, A1 and pin 3
- Joystick on A0, A1 and pin 8
- Keypad on pins 11 to 4
- Membrane keypad on pins 9 to 2
- LCD1602 on pins 4, 6 and 10 to 13
- LCD1602 on pins 7 to 12
- LCD1602 hello
- MAX7219 8x8 matrix (pins 12, 10 and 11)
- Morse code on an active buzzer (pin 9)
- MPU-6050 readings over I2C
- Passive buzzer scale on pin 12
- Passive buzzer module on pin 3
- Passive buzzer on pin 8
- Motion sensor on pin 3 lights the LED on 13
- Motion sensor on pin 12 lights the LED on 13
- Pomodoro timer on an active buzzer (pin 9)
- RC522 RFID reader (SS 10, RST 9)
- Real-time clock
- Servo sweep
- Servo sweep on pin 10
- Servo sweep on pin 3
- Siren on a passive buzzer (pin 9)
- Ultrasonic distance on pins 12 and 11
- Ultrasonic sensor on 8 and 7, the LED on 13 when out of range
- Sound sensor on A0 and pin 3
- Analog sound module on A0
- Stepper motor on pins 8 to 11
- Twinkle, Twinkle, Little Star on a passive buzzer (pin 9)
- Water level sensor
- Read a knob
- MAX7219 scrolling text display
- Operating point and sweep
- Digital piano
- Fade an LED
- First blink
- IR decoder
- Blink an LED on pin 13, once a second
- Blink an LED on pin 3
- Blink an LED on pin 8
- Blink an LED on pin 9
- Breathing LED on pin 5
- Button on pin 12 lights the LED on pin 13
- Answer ball
- Flowing lights on pins 2 to 9
- IR remote codes on pin 12
- IR receiver module on pin 11
- IR receiver on pin 2
- LED module on pin 7, blinking
- An LED on the 5 V pin
- Mood dial
- Four brightnesses from PWM: pins 5, 6, 9 and 10
- RGB colors on pins 11, 10 and 9
- RGB LED on pins 3, 5 and 6
- RGB fade on pins 6, 5 and 3
- RGB LED module: red 11, blue 10, green 9
- Random colors on an RGB LED (pins 11, 10 and 9)
- Set the LED on pin 11 from the serial monitor
- A knob on A0 points the servo on pin 3
- Seven-segment digit on pins 4 to 11
- Thermometer: a thermistor on A0
- Tilt switch on pin 3 lights the LED on 13
- Traffic lights on pins 3, 4 and 5
- Two LEDs take turns on pins 4 and 5
- RGB color mixer
- Arduino Uno blink
- Light-up Valentine heart
- Button and LED
- Grabbing candy bowl
- Hatching chick
- Clap switch
- Passive buzzer alarm on pin 9, through a transistor
- Push button on pin 12 lights the LED on pin 9
- A push button lights an LED, no code
- Push button on pin 12 toggles the LED on pin 9
- Dinosaur game player: light sensor on A0, servo on 9
- Doorbell: button on pin 2, buzzer on pin 8
- Tilt hourglass
- Remote control light switch (IR on 12, servo on 11)
- Joystick lights the way (LEDs on 8 to 11)
- Four-key keyboard
- Knob on A0 dims the LED on pin 9
- Photoresistor night light: A0 dims the LED on pin 9
- Light meter: photoresistor on A0, LEDs on pins 5 to 12
- PIR motion light
- Motion night light (PIR on 12, RGB on 5, 6 and 9)
- Three knobs mix an RGB LED (pins 11, 10 and 9)
- Starship control panel
- Tilt switch on A5 lights the LED on pin 8
- Tilt switch
- Traffic lights with a crossing button on pin 8
- Two buttons, one LED
- Warm or cool light: a knob blends an RGB LED
- Motion light
- Night light
- Ofrenda candles
- Piezo melody
- Power module
- Rotary encoder
- Dimmer
- Night light with a light sensor
- A button doorbell with a lamp, no code
- Transistor doorbell: button on 12, buzzer on 9
- Metronome
- Police lights and siren
- Rescue beacon
- Relay on pin 8 through a transistor

Intermediate (72)

- Two Arduino Unos talking over serial
- DHT11 on A0, read with no library
- LCD1602 in 8-bit mode on pins 2 to 12
- Matrix ball
- DHT11 on pin 3, readings on an LCD
- Knob stepper
- DC motor on an L293D (pins 5, 3 and 4)
- Radar sweep: ultrasonic on 10 and 11, servo on 12
- Smart trash can: ultrasonic on 8 and 7, servo lid on 9
- Ultrasonic distance on an LCD (TRIG 2, ECHO 3)
- Stepper follows a knob (pins 2 to 5)
- Tilt snake on an 8x8 matrix
- Motor both ways
- Stepper turntable
- Arpeggiator
- LED bar chaser
- Electronic dice
- Joystick bar graph
- Kalman filter tilt angle with an MPU6050
- Hex digits on a common-anode display (74HC595, pins 11, 12, 13)
- Countdown digit
- Hex digits through a 74HC595 (pins 11, 8 and 12)
- One-digit countdown on a 74HC595 (pins 2, 4 and 3)
- One-digit countdown on a 74HC595 (pins 8, 10 and 9)
- Falling rain on eight LEDs (74HC595, pins 11, 12 and 13)
- Flowing light on a 74HC595 (pins 11, 8 and 12)
- Eight LEDs on a 74HC595 (pins 12, 9 and 11)
- Eight LEDs on a 74HC595 (pins 2, 5 and 4)
- A light runs along eight LEDs on a 74HC595 (pins 11, 12 and 13)
- Serial monitor drives eight LEDs (74HC595)
- Type a digit: serial to a 74HC595 display (pins 11, 8 and 12)
- Cyber dice: seven-segment on pins 2 to 8, button on 9
- Summer fan: four buttons and an L293D (pins 9 and 10)
- Four-digit display on a 74HC595 (pins 8, 10 and 9)
- A knob drives a motor both ways through an L293D
- Relay switched by an L293D (pins 5, 3 and 4)
- Ultrasonic ranging on an LCD
- Thermistor thermometer on an LCD (pins 7 to 12)
- Remote stepper
- Remote stepper, a whole turn a press
- Rotary encoder on pins 2, 3 and 4, LEDs on 5 and 6
- Temperature alarm: thermistor on A0, RGB on 10, 11 and 12
- Thermistor thermometer
- Thermistor on A0, degrees on an LCD (pins 4, 6, 10 to 13)
- RFID door
- Tilt meter
- Remote-controlled lamps
- Photocell bar graph on a 74HC595
- Photoresistor bar graph on a 74HC595 (pins 9, 12 and 11)
- Digital dice on a 74HC595 (pins 11, 8 and 12)
- Three-speed fan on an L293D (pins 9 and 10)
- Remote-controlled colors: IR on pin 2, RGB on 11, 10 and 9
- Photocell light meter
- Quiz buzzer for three players
- Tilt dice on an 8x8 matrix
- Looper
- Motor on a transistor
- Servo turnouts with a panel
- Reaction duel
- Parking sensor
- Tap-tempo metronome
- ADSR synth
- Combination lock: keypad, servo bolt and buzzer
- Catch the beans: a tilt game on an 8x8 matrix
- Reaction timer
- Ringtone player
- Remote dimmer: IR on 12, LED on 5, buzzer on 13
- Memory math game on an LCD and an IR remote
- Relay switches a motor
- Spinning zoetrope
- Lion dance head
- Relay switches a motor: button on 12, relay on 9

Advanced (13)

- Two Arduino Unos as an SPI master and slave
- Stopwatch on a four-digit display
- Stopwatch: four-digit display, digits on 10 to 13
- Four-digit counter
- MPU6050 servo stabilizer
- Snake on two matrices
- Four digits from one 74HC595 (pins 11, 12, 13 and 7 to 4)
- Game of Life
- Grid sequencer
- RFID time clock with an LCD and a DS1307
- 4x4x4 LED cube
- Countdown timer on a four-digit display
- Alarm clock with a timer on a four-digit display

Level up

## Add a few parts, unlock more projects

The smallest shopping lists that open the most new projects for the ELEGOO UNO R3 Most Complete Starter Kit.

### Add Character LCD with I2C backpack

Unlocks 18 more projects:

- I2C LCD1602: find its address, then say hello
- Dreidel spinner
- Eid greeting card
- Message display gift
- Red envelope box
- Pi digits on an LCD
- and 12 more

### Add Character LCD with I2C backpack and Addressable RGB LEDs

Unlocks 33 more projects:

- I2C LCD1602: find its address, then say hello
- Diwali diya row
- Dreidel spinner
- Marigold path
- Hanukkah menorah
- Rainbow to the pot of gold
- and 27 more

### Add ili9341, Character LCD with I2C backpack and Addressable RGB LEDs

Unlocks 46 more projects:

- I2C LCD1602: find its address, then say hello
- Diwali diya row
- Dreidel spinner
- Marigold path
- Hanukkah menorah
- Rainbow to the pot of gold
- and 40 more

Two kits

## Projects that combine two kits

Own another kit as well? These need parts from both boxes, and neither can build them alone.

### With the SunFounder Kepler Kit for Raspberry Pi Pico W

46 projects:

- I2C LCD1602: find its address, then say hello
- LED bar graph on pins 3 to 12
- Touch piano
- Diwali diya row
- Dreidel spinner
- and 41 more

### With the SunFounder ESP32 Ultimate Starter Kit

45 projects:

- I2C LCD1602: find its address, then say hello
- Line tracking sensor on pin 3
- Obstacle sensor on pin 3 lights the LED on 13
- Diwali diya row
- Dreidel spinner
- and 40 more

### With the Kitronik Inventor’s Kit for the Raspberry Pi Pico

41 projects:

- MicroPython joystick on a Pico: X, Y and the press
- DHT11 on a Pico with MicroPython
- MicroPython DHT11 on a Pico: temperature and humidity
- MicroPython color wheel on a Pico’s RGB LED
- MicroPython random colors on a Pico’s RGB LED
- and 36 more

### With the Freenove Ultimate Starter Kit for Raspberry Pi Pico

38 projects:

- I2C LCD1602: find its address, then say hello
- Pico W water level sensor on GP28
- Pico W tilt switch on GP14
- LED bar graph on pins 3 to 12
- Diwali diya row
- and 33 more

Free course

## Learn it as a course, step by step

The same lessons as a guided course: chapters, projects and every step checked by the simulator.

Starter kit companion: the 33-lesson kit

33 lessons, 10 of them from this kit

Starter kit companion: the 24-lesson kit

24 lessons, 6 of them from this kit

In the box

## The kit’s parts, and what plays them here

The parts in the ELEGOO UNO R3 Most Complete Starter Kit, by the names its maker gives them. Each one is in the editor’s parts panel.

- UNO R3 Controller Board Arduino Uno R3
- 830 Tie-Points Breadboard Full-size breadboard
- Red, Yellow, Blue, Green and White LED LED
- RGB LED RGB LED
- Resistor Resistor
- Button Pushbutton
- Potentiometer Potentiometer
- Tilt Ball Switch Tilt switch
- Active Buzzer Buzzer
- Passive Buzzer Piezo speaker
- Servo Motor SG90 Hobby servo
- Ultrasonic Sensor Ultrasonic ranger
- Membrane Switch Module Keypad, 4x4
- DHT11 Temperature and Humidity Module Temperature and humidity, DHT22 Set to the DHT11 model on the canvas.
- Joystick Module Thumb stick
- IR Receiver Module Infrared receiver, VS1838B
- Remote Control Infrared remote, 21 buttons
- MAX7219 Module LED matrix, 8x8
- GY-521 Module (MPU6050) Accelerometer and gyroscope, MPU6050 Some boxes ship a QMI-8658 board instead, which is not simulated yet.
- HC-SR501 PIR Motion Sensor Module Motion sensor
- Water Level Detection Sensor Module Water level sensor
- DS1307 RTC Module Real-time clock, DS1307
- Sound Sensor Module Sound sensor, KY-038
- RC522 RFID Module RFID reader, MFRC522
- LCD1602 Module (with pin header) Character LCD, 16x2
- 74HC595 IC 74HC595 shift register
- Fan Blade and 3-6V Motor DC motor
- L293D Motor driver, L293D
- ULN2003 Stepper Motor Driver Module and Stepper Motor Stepper motor, 28BYJ-48 with ULN2003
- Thermistor Thermistor, 10k NTC
- 1 Digit 7-Segment Display Seven segment display
- 4 Digit 7-Segment Display Four-digit seven segment, multiplexed
- Photoresistor (Photocell) Light sensor
- 5V Relay DPDT relay
- Rotary Encoder Module Rotary encoder, KY-040
- NPN Transistor PN2222 Transistor (NPN or PNP) Set to 2N2222, the same transistor.
- NPN Transistor S8050 Transistor (NPN or PNP) Set to S8050.
- Diode Rectifier Diode Set to 1N4007, the diode in the kit’s datasheets.
- 100uF and 10uF Electrolytic Capacitor Capacitor
- 104pF and 22pF Ceramic Capacitor Capacitor The one marked 104 is 100 nF.
- Power Supply Module Breadboard power supply, MB102
- 9V Battery with Snap-on Connector Clip Battery: AA, coin cell, LiPo The battery is set to 9 V.
- 9V1A Adapter A wall supply for the board; the editor powers the board for you.
- ALL IN ONE Sensor Shield No model of this shield yet; the lessons here wire the same parts on a breadboard to the pins the shield uses.
- USB Cable The editor connects the board for you.
- Breadboard Jumper Wire, Female-to-Male and Female-to-Female Dupont Wire Drawn as wires between pins; nothing to place.

Parts list read from ELEGOO’s V2.0 tutorial download. An item with no part beside it has no match in the editor yet.

For the manual

## A link and a QR code for this page

Print either one beside a lesson, or tape it inside the box lid. Both open this page.

mokxi.com/k/elegoo-complete

The code is black on white with a quiet border, so it prints and scans at any size from 2 cm up.
Download the QR code (SVG)
Make kits? See what we offer kit makers.

FAQ

## Questions about this page

Is this made by ELEGOO?

No. Mokxi is independent and is not affiliated with ELEGOO. The page follows the kit’s lessons so you can use the two side by side; the circuits, sketches and explanations are Mokxi’s own.

Do I need the kit?

No. Every lesson that runs here runs in the browser, so you can try them before you buy a kit, or keep going while a part is missing or broken.

Is the code the same as in my manual?

The pins and the parts are the same, and the sketches use the same libraries where the kit does. The code itself is written for this page, with comments that explain each step, so it will not match the manual line for line.

What do "with a change" and "coming soon" mean?

A lesson marked "with a change" runs, but something differs from the kit, and the note under it says exactly what. "Coming soon" means we cannot simulate that lesson yet, and the note says why. We do not mark a lesson as running unless it does.

Is it free?

Yes. Every lesson on this page opens with no account. A free account saves your own copies of the circuits.

Keep going

## Other kits

Companion pages for more starter kits.

ELEGOO UNO R3 Super Starter Kit

25 lessons, 24 run in the browser

Arduino Starter Kit

15 lessons, 15 run in the browser

Freenove Ultimate Starter Kit

42 lessons, 42 run in the browser

ELEGOO UNO R3 Basic Starter Kit

11 lessons, 10 run in the browser

SunFounder Starter Kit for Arduino Uno R3

23 lessons, 23 run in the browser

SunFounder Inventor Lab Kit

34 lessons, 33 run in the browser

Keyestudio 37 in 1 Sensor Kit

37 lessons, 37 run in the browser

REXQualis UNO R3 Super Starter Kit

22 lessons, 21 run in the browser

LAFVIN Super Starter Kit

28 lessons, 27 run in the browser

Freenove Ultimate Starter Kit for ESP32-WROVER

54 lessons, 44 run in the browser

SunFounder Kepler Kit for Raspberry Pi Pico W

63 lessons, 48 run in the browser

Freenove Ultimate Starter Kit for Raspberry Pi Pico

56 lessons, 50 run in the browser

keyestudio Super Starter Kit

Projects you can build with its parts

Vilros Arduino Uno 3 Ultimate Starter Kit

Projects you can build with its parts

SunFounder Universal Maker Sensor Kit

Projects you can build with its parts

SunFounder ESP32 Ultimate Starter Kit

Projects you can build with its parts

Adafruit MetroX Classic Kit

Projects you can build with its parts

MonkMakes Electronics Kit 1 for Raspberry Pi Pico

Projects you can build with its parts

Kitronik Discovery Kit for Raspberry Pi Pico

Projects you can build with its parts

Kitronik Inventor’s Kit for the Raspberry Pi Pico

Projects you can build with its parts

Keyestudio ESP32 Learning Kit Ultimate Edition

Projects you can build with its parts

## Start at lesson one

Every project opens in the editor with no account and nothing to install. Run it, change a number, run it again.

See the lessons
