Source: https://mokxi.com/kits/companion/arduino-starter-kit
Updated: 2026-11-07

Kits / Kit companions
Kit companion

# Arduino Starter Kit: every lesson, simulated

The fifteen projects of the kit’s book, in its order, each as a circuit that runs in your browser on the pins the book uses. Build it here first, then on your bench.

Open the first lesson Find your lesson What else it can build

Not affiliated with Arduino. Lesson titles are referenced so you can follow along.

Lesson by lesson

## Every lesson in the kit’s order

Lesson numbers and titles follow the Arduino Projects Book, with the StarterKit_BasicKit examples that ship in the Arduino IDE. Each circuit uses the kit’s parts on the pins the lesson uses.

15 of the 15 lessons with a circuit run here, 3 of them with a change we name.

Project 01

### Get to Know Your Tools

Runs here

A switch, a resistor and an LED on the 5 V supply: your first circuit, wired by hand.

Open the guided lesson

Project 02

### Spaceship Interface

Runs here

A button on pin 2 with a 10k pull-down; a green lamp on 3 and two red lamps on 4 and 5.

Open in the editor Starship control panel

Project 03

### Love-o-Meter

Runs here

A TMP36 on A0 lights LEDs on pins 2, 3 and 4 as it warms up.

Open in the editor Warm-hands meter

Project 04

### Color Mixing Lamp

Runs, with a change

Three light sensors on A0, A1 and A2 set green on 9, red on 10 and blue on 11 of an RGB LED.

The colored gels are replaced by a light level on each sensor, which you set on the canvas.

Open in the editor Color-mixing lamp

Project 05

### Mood Cue

Runs here

A knob on A0 points a servo on pin 9.

Open in the editor Mood dial

Project 06

### Light Theremin

Runs here

A photoresistor on A0 sets the pitch of a piezo on pin 8.

Open in the editor Light theremin

Project 07

### Keyboard Instrument

Runs here

Four buttons on one analog pin through a resistor ladder, playing notes on a piezo on pin 8.

Open in the editor Four-key keyboard

Project 08

### Digital Hourglass

Runs here

Six LEDs on pins 2 to 7 count the time; turn the tilt switch on pin 8 to start again.

Open in the editor Tilt hourglass

Project 09

### Motorized Pinwheel

Runs here

A button on pin 2 switches a motor through the IRF520 MOSFET on pin 9.

Pin 9 drives the IRF520’s gate straight, as in the book. The IRF520 is specified at a 10 V gate; from the 5 V pin it is about 1 ohm, so it keeps a fifth of a volt of the battery from the motor.

Open in the editor Motor pinwheel

Project 10

### Zoetrope

Runs here

An H-bridge on pins 2, 3 and 9 runs a motor both ways; switches on 4 and 5 and a knob on A0 control it.

Open in the editor Spinning zoetrope

Project 11

### Crystal Ball

Runs here

Tilt the switch on pin 6 and the LCD on pins 12, 11, 5, 4, 3 and 2 answers your question.

Open in the editor Answer ball

Project 12

### Knock Lock

Runs, with a change

Three knocks open a servo lock on pin 9; a button on pin 2 locks it, LEDs on 3, 4 and 5 show the state.

The book listens for knocks with a piezo on A0. The simulated piezo only plays sound, so a force sensor on A0 stands in for it.

Open in the editor Knock lock on the book’s pins

Project 13

### Touchy-feely Lamp

Runs here

Foil on pin 2, a 1 megohm resistor from pin 4, and an LED on pin 12 that lights at a touch.

Open in the editor Touch lamp, LED on pin 12

Project 14

### Tweak the Arduino Logo

Runs, with a change

A knob on A0 sends its reading over serial for a program on your computer to use.

The board’s half runs here; the Processing sketch that changes the logo runs on your computer.

Open in the editor Read a knob

Project 15

### Hacking Buttons

Runs here

An optocoupler on pin 2 presses another gadget’s button without sharing a wire.

Open in the editor Opto press

Lesson list and pins read from the kit’s example sketches. The explanations on this page are our own.

Learning path

## Everything the Arduino Starter Kit can build

86 projects use only the parts in this box, ordered from a first blink to the hardest.

Beginner (67)

- EEPROM: memory that survives a reset
- Serial echo: the board repeats what you type
- LCD1602 on pins 4, 6 and 10 to 13
- LCD1602 on pins 7 to 12
- LCD1602 hello
- Passive buzzer scale on pin 12
- Passive buzzer module on pin 3
- Passive buzzer on pin 8
- Servo sweep
- Servo sweep on pin 10
- Servo sweep on pin 3
- Siren on a passive buzzer (pin 9)
- Twinkle, Twinkle, Little Star on a passive buzzer (pin 9)
- Read a knob
- Operating point and sweep
- Digital piano
- Fade an LED
- First blink
- Blink an LED on pin 13, once a second
- Blink an LED on pin 3
- Blink an LED on pin 8
- Blink an LED on pin 9
- Breathing LED on pin 5
- Button on pin 12 lights the LED on pin 13
- Answer ball
- Flowing lights on pins 2 to 9
- LED module on pin 7, blinking
- An LED on the 5 V pin
- Mood dial
- Four brightnesses from PWM: pins 5, 6, 9 and 10
- RGB colors on pins 11, 10 and 9
- RGB LED on pins 3, 5 and 6
- RGB fade on pins 6, 5 and 3
- RGB LED module: red 11, blue 10, green 9
- Random colors on an RGB LED (pins 11, 10 and 9)
- Set the LED on pin 11 from the serial monitor
- A knob on A0 points the servo on pin 3
- Tilt switch on pin 3 lights the LED on 13
- Traffic lights on pins 3, 4 and 5
- Two LEDs take turns on pins 4 and 5
- RGB color mixer
- Arduino Uno blink
- Button and LED
- Push button on pin 12 lights the LED on pin 9
- A push button lights an LED, no code
- Push button on pin 12 toggles the LED on pin 9
- Color-mixing lamp
- Doorbell: button on pin 2, buzzer on pin 8
- Tilt hourglass
- Four-key keyboard
- Knob on A0 dims the LED on pin 9
- Warm-hands meter
- Three knobs mix an RGB LED (pins 11, 10 and 9)
- Starship control panel
- Tilt switch on A5 lights the LED on pin 8
- Tilt switch
- Traffic lights with a crossing button on pin 8
- Two buttons, one LED
- Warm or cool light: a knob blends an RGB LED
- Light theremin
- Night light
- Ofrenda candles
- Piezo melody
- Dimmer
- Metronome
- Police lights and siren
- Motor pinwheel

Intermediate (18)

- Two Arduino Unos talking over serial
- LCD1602 in 8-bit mode on pins 2 to 12
- DC motor on an L293D (pins 5, 3 and 4)
- Motor both ways
- Thermometer
- Arpeggiator
- Summer fan: four buttons and an L293D (pins 9 and 10)
- A knob drives a motor both ways through an L293D
- Three-speed fan on an L293D (pins 9 and 10)
- Looper
- Opto press
- Servo turnouts with a panel
- Reaction duel
- Tap-tempo metronome
- ADSR synth
- Ringtone player
- Spinning zoetrope
- Lion dance head

Advanced (1)

- Two Arduino Unos as an SPI master and slave

Level up

## Add a few parts, unlock more projects

The smallest shopping lists that open the most new projects for the Arduino Starter Kit.

### Add Addressable RGB LEDs

Unlocks 13 more projects:

- Diwali diya row
- Love meter
- Marigold path
- Hanukkah menorah
- Rainbow to the pot of gold
- LED sparkler
- and 7 more

### Add Character LCD with I2C backpack and Addressable RGB LEDs

Unlocks 23 more projects:

- I2C LCD1602: find its address, then say hello
- Diwali diya row
- Dreidel spinner
- Love meter
- Marigold path
- Hanukkah menorah
- and 17 more

### Add ili9341, Character LCD with I2C backpack and Addressable RGB LEDs

Unlocks 32 more projects:

- I2C LCD1602: find its address, then say hello
- Diwali diya row
- Dreidel spinner
- Love meter
- Marigold path
- Hanukkah menorah
- and 26 more

Two kits

## Projects that combine two kits

Own another kit as well? These need parts from both boxes, and neither can build them alone.

### With the SunFounder Kepler Kit for Raspberry Pi Pico W

138 projects:

- Active buzzer
- Active buzzer module on pin 3
- DHT11 temperature and humidity
- DHT11 module on pin 4
- DHT11 temperature and humidity on pin 10
- and 133 more

### With the Freenove Ultimate Starter Kit for Raspberry Pi Pico

135 projects:

- Active buzzer
- Active buzzer module on pin 3
- DHT11 temperature and humidity
- DHT11 module on pin 4
- DHT11 temperature and humidity on pin 10
- and 130 more

### With the Freenove Ultimate Starter Kit for ESP32-WROVER

128 projects:

- Active buzzer
- Active buzzer module on pin 3
- DHT11 temperature and humidity
- DHT11 module on pin 4
- DHT11 temperature and humidity on pin 10
- and 123 more

### With the SunFounder ESP32 Ultimate Starter Kit

106 projects:

- Active buzzer
- Active buzzer module on pin 3
- DHT11 temperature and humidity
- DHT11 module on pin 4
- DHT11 temperature and humidity on pin 10
- and 101 more

Free course

## Learn it as a course

The same lessons as a guided course: chapters, projects and every step checked by the simulator.

Starter kit companion: the project book

15 lessons, 10 of them from this kit

In the box

## The kit’s parts, and what plays them here

The parts in the Arduino Starter Kit, by the names its maker gives them. Each one is in the editor’s parts panel.

- Arduino Uno Arduino Uno R3
- Breadboard, 400 points Full-size breadboard The kit’s breadboard is the 400-point half size.
- Projects Book (170 pages) The printed book; nothing to place.
- USB cable The editor connects the board for you.
- Solid core jumper wires, and stranded jumper wires (black and red) Drawn as wires between pins; nothing to place.
- Easy-to-assemble wooden base A holder for the board and breadboard; nothing to place.
- 9V battery snap Battery: AA, coin cell, LiPo The battery is set to 9 V; the kit has the snap, not the battery.
- Phototransistor Phototransistor
- Potentiometer, 10kOhms Potentiometer
- Pushbuttons Pushbutton
- Temperature sensor [TMP36] Temperature sensor, TMP36
- Tilt sensor Tilt switch
- Alphanumeric LCD (16x2 characters) Character LCD, 16x2
- LEDs (bright white, red, green, yellow and blue) LED
- LED (RGB) RGB LED
- Small DC motor, 6/9V DC motor
- Small servo motor Hobby servo
- Piezo capsule [PKM22EPP-40] Piezo speaker
- H-bridge motor driver [L293D] Motor driver, L293D
- Optocouplers [4N35] Optocoupler, 4N35
- Mosfet transistors [IRF520] MOSFET Set to IRF520.
- Capacitors, 100uF Capacitor
- Diodes [1N4007] Diode Set to 1N4007.
- Transparent gels (red, green, blue) Color filters for the phototransistors; nothing to place.
- Male pins strip (40x1) Header pins for soldering; nothing to place.
- Resistors, 220 Ohms, 560 Ohms, 1 kOhms, 4.7 kOhms, 10 kOhms, 1 MOhms and 10 MOhms Resistor

Parts list read from the Arduino Store page for the Starter Kit. An item with no part beside it has no match in the editor yet.

For the manual

## A link and a QR code for this page

Print either one beside a lesson, or tape it inside the box lid. Both open this page.

mokxi.com/k/arduino-starter

The code is black on white with a quiet border, so it prints and scans at any size from 2 cm up.
Download the QR code (SVG)
Make kits? See what we offer kit makers.

FAQ

## Questions about this page

Is this made by Arduino?

No. Mokxi is independent and is not affiliated with Arduino. The page follows the kit’s lessons so you can use the two side by side; the circuits, sketches and explanations are Mokxi’s own.

Do I need the kit?

No. Every lesson that runs here runs in the browser, so you can try them before you buy a kit, or keep going while a part is missing or broken.

Is the code the same as in my manual?

The pins and the parts are the same, and the sketches use the same libraries where the kit does. The code itself is written for this page, with comments that explain each step, so it will not match the manual line for line.

What do "with a change" and "coming soon" mean?

A lesson marked "with a change" runs, but something differs from the kit, and the note under it says exactly what. "Coming soon" means we cannot simulate that lesson yet, and the note says why. We do not mark a lesson as running unless it does.

Is it free?

Yes. Every lesson on this page opens with no account. A free account saves your own copies of the circuits.

Keep going

## Other kits

Companion pages for more starter kits.

ELEGOO UNO R3 Super Starter Kit

25 lessons, 24 run in the browser

ELEGOO UNO R3 Most Complete Starter Kit

48 lessons, 44 run in the browser

Freenove Ultimate Starter Kit

42 lessons, 42 run in the browser

ELEGOO UNO R3 Basic Starter Kit

11 lessons, 10 run in the browser

SunFounder Starter Kit for Arduino Uno R3

23 lessons, 23 run in the browser

SunFounder Inventor Lab Kit

34 lessons, 33 run in the browser

Keyestudio 37 in 1 Sensor Kit

37 lessons, 37 run in the browser

REXQualis UNO R3 Super Starter Kit

22 lessons, 21 run in the browser

LAFVIN Super Starter Kit

28 lessons, 27 run in the browser

Freenove Ultimate Starter Kit for ESP32-WROVER

54 lessons, 44 run in the browser

SunFounder Kepler Kit for Raspberry Pi Pico W

63 lessons, 48 run in the browser

Freenove Ultimate Starter Kit for Raspberry Pi Pico

56 lessons, 50 run in the browser

keyestudio Super Starter Kit

Projects you can build with its parts

Vilros Arduino Uno 3 Ultimate Starter Kit

Projects you can build with its parts

SunFounder Universal Maker Sensor Kit

Projects you can build with its parts

SunFounder ESP32 Ultimate Starter Kit

Projects you can build with its parts

Adafruit MetroX Classic Kit

Projects you can build with its parts

MonkMakes Electronics Kit 1 for Raspberry Pi Pico

Projects you can build with its parts

Kitronik Discovery Kit for Raspberry Pi Pico

Projects you can build with its parts

Kitronik Inventor’s Kit for the Raspberry Pi Pico

Projects you can build with its parts

Keyestudio ESP32 Learning Kit Ultimate Edition

Projects you can build with its parts

## Start at lesson one

Every project opens in the editor with no account and nothing to install. Run it, change a number, run it again.

See the lessons
