Source: https://mokxi.com/ideas/weather
Updated: 2026-11-17

Projects / Project ideas
Weather

# Weather station projects

These are the weather stations, barometers, thermometers and rain gauges named for what they measure, and every project built on a BME280. Mokxi has 30 of them (10 beginner, 19 intermediate and 1 advanced). Here are 24, from “NTC thermometer” to “LoRa weather station with acknowledgments”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

## How to pick your first one

- Start with “CircuitPython BME280 on a Pico”, a beginner project that needs a BME280 sensor.
- Most of them are intermediate projects. Pick one a level below what you think you can do, finish it, then move up.
- The parts used most here are the BME280 weather sensor (7 projects), the I2C LCD (7) and the 10k NTC thermistor (7). With those on hand, most of this list is open to you.
- Read one sensor and print it to the serial monitor before you add a display or WiFi; a reading that is wrong on serial will be wrong everywhere else too.

Projects

## 24 projects of 30

### NTC thermometer

The NTC temperature sensor module on A0, worked out in degrees with the beta equation every tutorial for it uses.

Board

Arduino Uno R3

Parts

NTC temperature sensor module

Level

Beginner

Open in the simulator

### CircuitPython BME280 on a Pico

CircuitPython on a Raspberry Pi Pico: busio.I2C and Adafruit’s adafruit_bme280 read the temperature.

Board

Raspberry Pi Pico

Parts

BME280 weather sensor

Level

Beginner

Open in the simulator

### DHT11 temperature and humidity

A DHT11 module on pin 2: the DHT library reads the temperature and humidity every two seconds and prints both.

Board

Arduino Uno R3

Parts

DHT11 or DHT22 sensor

Level

Beginner

Open in the simulator

### Pico W DHT11 temperature and humidity on GP16

MicroPython on a Pico W: the dht module reads a DHT11 on GP16 and prints the temperature and humidity every two seconds, retrying a failed read.

Board

Raspberry Pi Pico W

Parts

DHT11 or DHT22 sensor

Level

Beginner

Open in the simulator

### Fever thermometer

An MLX90614 reads a forehead without touching it; an I2C LCD shows the temperature, and over 38 C it says FEVER and beeps.

Board

Arduino Uno R3

Parts

IR thermometer, I2C LCD, piezo speaker

Level

Beginner

Open in the simulator

### Pico W thermistor thermometer on GP28

MicroPython on a Pico W: a 10k thermistor divider on GP28, its resistance turned into Celsius and Fahrenheit with the beta equation, once a second.

Board

Raspberry Pi Pico W

Parts

Resistor, 10k NTC thermistor

Level

Beginner

Open in the simulator

### MicroPython BME280 weather on an OLED

MicroPython on a Raspberry Pi Pico: machine.I2C reads a BME280 and shows temperature, pressure and humidity on an SSD1306 OLED with ssd1306.py.

Board

Raspberry Pi Pico

Parts

SSD1306 OLED display, BME280 weather sensor

Level

Intermediate

Open in the simulator

### WiFi: fetch the weather

HTTPClient against a simulated origin, with the numbers on a dial in the Cloud panel, and a request to the real internet that is refused.

Board

ESP32-C3-DevKitM-1

Parts

Just the board

Level

Intermediate

Open in the simulator

### Indoor and outdoor thermometer on two OLEDs

Two BME280s and two SSD1306 OLEDs share their addresses, so a TCA9548A puts each pair on its own channel: each screen shows its own weather.

Board

Arduino Uno R3

Parts

I2C multiplexer, BME280 weather sensor, SSD1306 OLED display

Level

Intermediate

Open in the simulator

### ESP32 DHT22 weather web server

ESP32 DHT22 weather web server: the board serves its own page with the temperature in C and F and the humidity, plus the same reading as JSON.

Board

ESP32 DevKit V1

Parts

DHT11 or DHT22 sensor

Level

Intermediate

Open in the simulator

### Pico W WiFi weather and time on an I2C LCD

MicroPython on a Pico W: join the simulated WiFi, fetch the weather and the time with urequests, and show both on an I2C LCD1602 on GP6 and GP7.

Board

Raspberry Pi Pico W

Parts

I2C LCD

Level

Intermediate

Open in the simulator

### Barometer

A BMP180 read with the Adafruit BMP085 library: temperature to a tenth of a degree, pressure to a pascal, and the altitude that pressure means.

Board

Arduino Uno R3

Parts

BMP180 pressure sensor

Level

Intermediate

Open in the simulator

### Thermometer

A TMP36 on A0 and the temperature on a 16x2 LCD in four-bit mode, with the high and low on the second row.

Board

Arduino Uno R3

Parts

TMP36 temperature sensor, 16x2 character LCD

Level

Intermediate

Open in the simulator

### BME280 on a Pi Zero 2 W with smbus2

A Raspberry Pi Zero 2 W reads a BME280 over I2C with smbus2 and the datasheet formulas: temperature, pressure and humidity every two seconds.

Board

Raspberry Pi Zero 2 W

Parts

BME280 weather sensor

Level

Intermediate

Open in the simulator

### MicroPython thermometer: a thermistor on GPIO 36

MicroPython on an ESP32: a 10k NTC thermistor in a divider on GPIO 36, turned into degrees Celsius with the beta equation every second.

Board

ESP32-DevKitC V4

Parts

Resistor, 10k NTC thermistor

Level

Intermediate

Open in the simulator

### Two barometers

A BME280 and a BMP280 on one I2C bus, told apart by their address straps and their chip ids.

Board

ESP32-C3-DevKitM-1

Parts

BME280 weather sensor, pressure and temperature

Level

Intermediate

Open in the simulator

### Wind and rain station

The SparkFun weather meter kit on an Uno: wind speed from the anemometer, direction from the vane and rain from the bucket, on an I2C LCD.

Board

Arduino Uno R3

Parts

Weather meter kit, resistor, I2C LCD

Level

Intermediate

Open in the simulator

### ESP32 async web server: BME280, slider and relay

ESPAsyncWebServer serves a page with BME280 temperature, humidity and pressure, a slider that dims an LED and a button that switches a relay.

Board

ESP32 DevKit V1

Parts

BME280 weather sensor, resistor, LED, relay module, DC jack and adapter, +1 more

Level

Intermediate

Open in the simulator

### MicroPython WiFi weather on an ESP32

MicroPython on an ESP32 DevKit: network.WLAN joins the simulated access point and urequests fetches the weather from http.

Board

ESP32 DevKit V1

Parts

Just the board

Level

Intermediate

Open in the simulator

### Thermistor thermometer

A 10k thermistor and a 10k resistor make a divider on A0, and the beta equation turns the reading into degrees on a 16x2 LCD.

Board

Arduino Uno R3

Parts

10k NTC thermistor, resistor, 16x2 character LCD

Level

Intermediate

Open in the simulator

### I2C LCD clock and thermometer

An I2C LCD on A4 and A5 shows the time, kept by a timer interrupt every second, and the temperature from a thermistor on A0.

Board

Arduino Uno R3

Parts

10k NTC thermistor, resistor, I2C LCD

Level

Intermediate

Open in the simulator

### Falling rain on eight LEDs (74HC595, pins 11, 12 and 13)

Eight LEDs on a 74HC595 (DS 11, ST_CP 12, SH_CP 13) show a drop of light with a fading tail running along them.

Board

Arduino Uno R3

Parts

74HC595 shift register, resistor, LED

Level

Intermediate

Open in the simulator

### Weather station

A DHT22 on one wire and a 16x2 I2C display on two. Forty bits and a checksum, a first reading that fails, and a sensor that will not be hurried.

Board

Arduino Uno R3

Parts

DHT11 or DHT22 sensor, I2C LCD

Level

Intermediate

Open in the simulator

### LoRa weather station with acknowledgments

A BME280 node sends temperature, humidity and pressure over LoRa with RadioHead, and a gateway acknowledges each reading and shows it on an I2C LCD.

Board

Arduino Uno R3

Parts

LoRa module, BME280 weather sensor, I2C LCD

Level

Advanced

Open in the simulator

Keep going

## Wiring, libraries and more ideas

Every project ideas list

### Wiring guides

- BME280 to Arduino Uno
- I2C LCD to Arduino Uno
- I2C LCD to Raspberry Pi Pico
- BME280 to ESP32
- I2C LCD to ESP32
- DHT22 to Arduino Uno
- DHT22 to Raspberry Pi Pico
- DHT22 to ESP32

### Library pages

- LiquidCrystal I2C library
- Adafruit BME280 library
- DHT sensor library
- LiquidCrystal library
- Adafruit BMP085 library
- Adafruit GFX library

### More project ideas

- Arduino Uno project ideas
- ESP32 project ideas
- Raspberry Pi Pico project ideas
- Projects with a BME280 sensor
- Projects with an I2C LCD
- Projects with a thermistor
- Projects with a DHT11 or DHT22 sensor
- Projects with a 16x2 LCD
- LED projects for Arduino, ESP32 and Pico
- OLED display projects
- Projects with a 74HC595 shift register
