Source: https://mokxi.com/ideas/stepper28byj-projects
Updated: 2026-11-17

Projects / Project ideas
Project ideas by part

# Projects with a 28BYJ-48 stepper motor

13 Mokxi projects use a 28BYJ-48 stepper motor (1 beginner, 8 intermediate and 4 advanced). They run on Arduino Uno, Arduino Nano and ESP32 boards. Here are all of them, from “Stepper motor on pins 8 to 11” to “Pick and place”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

## How to pick your first one

- Start with “Stepper motor on pins 8 to 11”, a beginner project that needs a 28BYJ-48 stepper motor.
- Arduino Uno runs 10 of them, Arduino Nano 1 and ESP32 1. Start on the board you have, or on an Arduino Uno if you are buying one.
- The parts used most here are the I2C LCD (4 projects), the push button (4) and the servo motor (3). With those on hand, most of this list is open to you.
- Before you build one on a real bench, read the 28BYJ-48 stepper and ULN2003 wiring guide for your board below. It gives every pin and the voltage notes.

Projects

## 13 projects ready to run

### Stepper motor on pins 8 to 11

A 28BYJ-48 on its ULN2003 board with IN1 to IN4 on pins 8 to 11: the Stepper library turns the shaft one full turn one way, then back.

Board

Arduino Uno R3

Parts

28BYJ-48 stepper and ULN2003

Level

Beginner

Open in the simulator

### Stepper dial on the analyzer

A 28BYJ-48 following a knob, with a logic analyzer on its four coil lines: the half-step sequence walking, and the capture as CSV.

Board

Arduino Uno R3

Parts

28BYJ-48 stepper and ULN2003, potentiometer, logic analyzer

Level

Intermediate

Open in the simulator

### MicroPython stepper motor on a Pico, GP21 to GP18

MicroPython on a Raspberry Pi Pico: a 28BYJ-48 stepper on a ULN2003 board, driven from GP21 to GP18, turns once one way and once back.

Board

Raspberry Pi Pico

Parts

Battery: AA, 28BYJ-48 stepper and ULN2003

Level

Intermediate

Open in the simulator

### Remote stepper

An IR receiver on pin 12 and a 28BYJ-48 on its ULN2003 board: VOL+ turns the shaft a quarter turn and VOL- turns it back.

Board

Arduino Uno R3

Parts

28BYJ-48 stepper and ULN2003, IR receiver and remote, IR remote

Level

Intermediate

Open in the simulator

### Knob stepper

A rotary encoder on pins 2, 3 and 4 steers a 28BYJ-48 click for click; press the knob and the shaft goes home.

Board

Arduino Uno R3

Parts

28BYJ-48 stepper and ULN2003, KY-040 rotary encoder

Level

Intermediate

Open in the simulator

### MicroPython stepper motor on a ULN2003 board

MicroPython on an ESP32: a 28BYJ-48 stepper on its ULN2003 board, IN1 to IN4 on GPIO 14, 27, 26 and 25, turns once one way and once back.

Board

ESP32-DevKitC V4

Parts

28BYJ-48 stepper and ULN2003

Level

Intermediate

Open in the simulator

### Stepper follows a knob (pins 2 to 5)

A 28BYJ-48 on its ULN2003 board with IN1 to IN4 on pins 2 to 5 follows a potentiometer on A0: turn the knob and the shaft turns to match.

Board

Arduino Uno R3

Parts

28BYJ-48 stepper and ULN2003, potentiometer

Level

Intermediate

Open in the simulator

### Animated diorama: DFPlayer sound + stepper

A button plays a C-3PO line on a DFPlayer Mini while a 28BYJ-48 turns R2-D2’s dome.

Board

Arduino Nano

Parts

DFPlayer Mini MP3 module, resistor, push button, 8 ohm speaker, 28BYJ-48 stepper and ULN2003

Level

Intermediate

Open in the simulator

### Stepper turntable

A photo turntable on a 28BYJ-48 and its ULN2003 board with AccelStepper: press the button and the plate turns a full circle in eight stops.

Board

Arduino Uno R3

Parts

Push button, 28BYJ-48 stepper and ULN2003

Level

Intermediate

Open in the simulator

### Access control: RFID card opens a stepper door

An RC522 reader (SS 10, RST 9) checks each card against the one it knows.

Board

Arduino Uno R3

Parts

MFRC522 RFID reader, 28BYJ-48 stepper and ULN2003, I2C LCD

Level

Advanced

Open in the simulator

### Satellite tracker

A stepper and a servo point a small dish at a satellite on a demo pass, from a simplified circular-orbit model.

Board

Arduino Uno R3

Parts

28BYJ-48 stepper and ULN2003, servo motor, push button, resistor, LED, +2 more

Level

Advanced

Open in the simulator

### ASRS picker

A stepper carriage homes on a limit switch, then counts its steps to the shelf you type on a keypad.

Board

Arduino Uno R3

Parts

4x3 telephone keypad, servo motor, 28BYJ-48 stepper and ULN2003, limit switch, buzzer, +1 more

Level

Advanced

Open in the simulator

### Pick and place

Two steppers home to their switches, then each START moves a part from the pick point to the place point: nozzle down, vacuum on, up, across, down.

Board

Arduino Uno R3

Parts

Relay module, DC motor, servo motor, 28BYJ-48 stepper and ULN2003, limit switch, +2 more

Level

Advanced

Open in the simulator

Keep going

## Wiring, libraries and more ideas

The 28BYJ-48 stepper and ULN2003 part page Every project ideas list

### Wiring guides

- 28BYJ-48 stepper to Arduino Uno
- 28BYJ-48 stepper to Arduino Nano
- 28BYJ-48 stepper to Raspberry Pi Pico
- 28BYJ-48 stepper to Arduino Mega
- 28BYJ-48 stepper to ESP32

### Library pages

- Stepper library
- AccelStepper library
- GyverStepper library
- LiquidCrystal I2C library
- Servo library
- DFRobotDFPlayerMini library

### More project ideas

- Arduino Uno project ideas
- Arduino Nano project ideas
- ESP32 project ideas
- Raspberry Pi Pico project ideas
- Projects with an I2C LCD
- Projects with a push button
- Servo motor projects
- Projects with a buzzer
- Projects with a limit switch
- Projects with a potentiometer
- Projects with a DC motor
