Source: https://mokxi.com/ideas/soilmoisture-projects
Updated: 2026-11-17

Projects / Project ideas
Project ideas by part

# Projects with a soil moisture sensor

6 Mokxi projects use a capacitive soil moisture sensor (2 beginner, 2 intermediate and 2 advanced). They run on Arduino Uno and ESP32 boards. Here are all of them, from “Mini pump plant waterer” to “Plant monitor: light, soil, temperature and a pump”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

## How to pick your first one

- Start with “Mini pump plant waterer”, a beginner project that needs a soil moisture sensor, a relay module and a water pump.
- Arduino Uno runs 5 of them and ESP32 1. Start on the board you have, or on an Arduino Uno if you are buying one.
- The parts used most here are the I2C LCD (2 projects), the photoresistor module (2) and the LED (2). With those on hand, most of this list is open to you.
- Before you build one on a real bench, read the capacitive soil moisture sensor wiring guide for your board below. It gives every pin and the voltage notes.

Projects

## 6 projects ready to run

### Mini pump plant waterer

A capacitive soil probe watches the pot; when it reads dry, a relay runs the mini pump for three seconds, then waits for the water to soak in.

Board

Arduino Uno R3

Parts

Capacitive soil moisture sensor, relay module, mini water pump

Level

Beginner

Open in the simulator

### Plant sensor for Home Assistant

A capacitive soil sensor mapped between two calibration readings, a light level, and a thirsty LED with two thresholds so it does not flicker.

Board

ESP32-C3-DevKitM-1

Parts

Photoresistor module, capacitive soil moisture sensor, resistor, LED

Level

Beginner

Open in the simulator

### Automatic plant waterer

A soil moisture stake, a relay and a small pump water a plant when it gets dry, in short bursts with time to soak.

Board

Arduino Uno R3

Parts

Capacitive soil moisture sensor, water level sensor, push button, relay module, DC motor, +2 more

Level

Intermediate

Open in the simulator

### Plant monitor

A soil moisture sensor, a rain sensor and a water level sensor on three analog pins. Two read lower when wetter and one reads higher.

Board

Arduino Uno R3

Parts

Capacitive soil moisture sensor, rain sensor, water level sensor, resistor, LED

Level

Intermediate

Open in the simulator

### Mars rover

A rover that drives three waypoints by dead reckoning, steers around hazards it sees with a sonar mast, samples soil and light.

Board

Arduino Uno R3

Parts

L298N motor driver, 2WD robot car chassis, push button, SSD1306 OLED display, VL53L0X time-of-flight sensor, +3 more

Level

Advanced

Open in the simulator

### Plant monitor: light, soil, temperature and a pump

A photoresistor on A0, a soil moisture sensor on A1 and a thermistor on A2 report to an I2C LCD; when the soil dries out.

Board

Arduino Uno R3

Parts

Photoresistor, resistor, 10k NTC thermistor, L293D motor driver, capacitive soil moisture sensor, +2 more

Level

Advanced

Open in the simulator

Keep going

## Wiring, libraries and more ideas

The capacitive soil moisture sensor part page Every project ideas list

### Wiring guides

- soil moisture sensor to Arduino Uno
- soil moisture sensor to Arduino Mega
- soil moisture sensor to Arduino Nano
- soil moisture sensor to Raspberry Pi Pico

### Library pages

- LiquidCrystal I2C library
- Adafruit GFX library
- Adafruit SSD1306 library
- Servo library
- VL53L0X library

### More project ideas

- Arduino Uno project ideas
- ESP32 project ideas
- Projects with an I2C LCD
- Projects with a light sensor module
- LED projects for Arduino, ESP32 and Pico
- Projects with a push button
- Projects with a relay module
- Projects with a water level sensor
- Projects with a water pump
