Source: https://mokxi.com/ideas/science-fair
Updated: 2026-11-17

Projects / Project ideas
Science fair

# Arduino science fair projects

These projects are tagged science fair. Each one measures something real, so it can answer a question with numbers. Mokxi has 10 of them (4 beginner, 5 intermediate and 1 advanced). Here are all of them, from “Robotic hand with flex sensors” to “Orbit simulator”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

## How to pick your first one

- Start with “Laser ruler”, a beginner project that needs a VL53L0X time-of-flight sensor.
- Most of them are intermediate projects. Pick one a level below what you think you can do, finish it, then move up.
- The parts used most here are the I2C LCD (3 projects), the DHT11 or DHT22 sensor (1) and the 16x2 character LCD (1). With those on hand, most of this list is open to you.
- A science fair project needs a question and a measurement, so pick the build that measures the thing your question is about, then log readings over time.

Projects

## 10 projects ready to run

### Robotic hand with flex sensors

Robotic hand with flex sensors on an Arduino Mega: five flex sensors on a glove move five servo fingers, and the Serial Monitor names the gesture.

Board

Arduino Mega 2560 R3

Parts

Servo motor, flex sensor

Level

Beginner

Open in the simulator

### Laser ruler

A VL53L0X time-of-flight sensor over I2C, read with Pololu’s library: millimeters to the target, and “out of range” past about 1.2 m.

Board

Arduino Uno R3

Parts

VL53L0X time-of-flight sensor

Level

Beginner

Open in the simulator

### Geiger counter

A RadiationD-v1.1 Geiger counter board on an Uno: the clicks counted on an interrupt, a running minute of counts.

Board

Arduino Uno R3

Parts

Geiger counter, I2C LCD

Level

Beginner

Open in the simulator

### NTC thermometer

The NTC temperature sensor module on A0, worked out in degrees with the beta equation every tutorial for it uses.

Board

Arduino Uno R3

Parts

NTC temperature sensor module

Level

Beginner

Open in the simulator

### Weather station

A DHT22 on one wire and a 16x2 I2C display on two. Forty bits and a checksum, a first reading that fails, and a sensor that will not be hurried.

Board

Arduino Uno R3

Parts

DHT11 or DHT22 sensor, I2C LCD

Level

Intermediate

Open in the simulator

### Wind and rain station

The SparkFun weather meter kit on an Uno: wind speed from the anemometer, direction from the vane and rain from the bucket, on an I2C LCD.

Board

Arduino Uno R3

Parts

Weather meter kit, resistor, I2C LCD

Level

Intermediate

Open in the simulator

### Barometer

A BMP180 read with the Adafruit BMP085 library: temperature to a tenth of a degree, pressure to a pascal, and the altitude that pressure means.

Board

Arduino Uno R3

Parts

BMP180 pressure sensor

Level

Intermediate

Open in the simulator

### Thermometer

A TMP36 on A0 and the temperature on a 16x2 LCD in four-bit mode, with the high and low on the second row.

Board

Arduino Uno R3

Parts

TMP36 temperature sensor, 16x2 character LCD

Level

Intermediate

Open in the simulator

### Kitchen scale

A bar load cell on an HX711, read with the HX711 library: tare, a scale in counts per gram, and grams on the serial monitor.

Board

Arduino Uno R3

Parts

Load cell with HX711

Level

Intermediate

Open in the simulator

### Orbit simulator

A planet and its moon pull on each other on a 128x64 OLED, and a knob turns gravity up and down: round orbits, ovals, crashes and escapes.

Board

Arduino Uno R3

Parts

SSD1306 OLED display, potentiometer, push button

Level

Advanced

Open in the simulator

Keep going

## Wiring, libraries and more ideas

Every project ideas list

### Wiring guides

- I2C LCD to Arduino Uno
- I2C LCD to Arduino Mega
- DHT22 to Arduino Uno
- potentiometer to Arduino Uno
- push button to Arduino Uno
- servo to Arduino Uno
- SSD1306 OLED to Arduino Uno
- DHT22 to Arduino Mega

### Library pages

- LiquidCrystal I2C library
- Adafruit BMP085 library
- HX711 Arduino library
- LiquidCrystal library
- Servo library
- VL53L0X library

### More project ideas

- Arduino Uno project ideas
- Arduino Mega project ideas
- Projects with an I2C LCD
- Projects with a DHT11 or DHT22 sensor
- Projects with a 16x2 LCD
