Source: https://mokxi.com/ideas/relay-projects
Updated: 2026-11-17

Projects / Project ideas
Project ideas by part

# Projects with a relay module

21 Mokxi projects use a relay module (5 beginner, 8 intermediate and 8 advanced). They run on Arduino Uno and ESP32 boards. Here are all of them, from “On and off desk lamp: button on 7, relay on 2” to “Delta-T monitor”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

## How to pick your first one

- Start with “Mini pump plant waterer”, a beginner project that needs a soil moisture sensor, a relay module and a water pump.
- Arduino Uno runs 19 of them and ESP32 2. Start on the board you have, or on an Arduino Uno if you are buying one.
- The parts used most here are the LED (11 projects), the push button (11) and the slide switch (7). With those on hand, most of this list is open to you.
- Before you build one on a real bench, read the relay module wiring guide for your board below. It gives every pin and the voltage notes.

Projects

## 21 projects ready to run

### On and off desk lamp: button on 7, relay on 2

Board

Arduino Uno R3

Parts

Push button, resistor, LED, relay module

Level

Beginner

Open in the simulator

### Mini pump plant waterer

A capacitive soil probe watches the pot; when it reads dry, a relay runs the mini pump for three seconds, then waits for the water to soak in.

Board

Arduino Uno R3

Parts

Capacitive soil moisture sensor, relay module, mini water pump

Level

Beginner

Open in the simulator

### PIR motion light with a relay

After dark, an HC-SR501 PIR switches a 12 V lamp on through a relay, and it goes off 20 s after the last movement; a light sensor keeps it off by day.

Board

Arduino Uno R3

Parts

PIR motion sensor, photoresistor module, relay module, DC jack and adapter, filament lamp

Level

Beginner

Open in the simulator

### Relay module on pin 8

A relay module on pin 8 clicks on and off every two seconds; its contact switches an LED.

Board

Arduino Uno R3

Parts

Resistor, LED, relay module

Level

Beginner

Open in the simulator

### Fog machine trigger

A PIR fires a relay across a fog machine’s remote button for a short burst, then a cooldown with a red lamp lets the fog drift and the heater recover.

Board

Arduino Uno R3

Parts

Resistor, LED, PIR motion sensor, relay module

Level

Beginner

Open in the simulator

### ESP32 async web server: BME280, slider and relay

ESPAsyncWebServer serves a page with BME280 temperature, humidity and pressure, a slider that dims an LED and a button that switches a relay.

Board

ESP32 DevKit V1

Parts

BME280 weather sensor, resistor, LED, relay module, DC jack and adapter, +1 more

Level

Intermediate

Open in the simulator

### Garage door opener

A relay that presses the opener’s wall button for half a second and two reed switches that say closed, opening, open, closing or stopped.

Board

ESP32-C3-DevKitM-1

Parts

Reed switch, push button, relay module

Level

Intermediate

Open in the simulator

### Water level controller with float switches

Two float switches keep a tank between its low and high marks with a pump on a relay; a stuck float or a pump running dry stops it and blinks red.

Board

Arduino Uno R3

Parts

Float switch, push button, resistor, LED, relay module, +2 more

Level

Intermediate

Open in the simulator

### Ultrasonic water tank level monitor

An HC-SR04 in the lid reads the water level onto an I2C LCD, a relay pump refills from 20 to 90 percent, and a buzzer warns of an overflow.

Board

Arduino Uno R3

Parts

HC-SR04 ultrasonic sensor, relay module, mini water pump, buzzer, I2C LCD

Level

Intermediate

Open in the simulator

### Automatic plant waterer

A soil moisture stake, a relay and a small pump water a plant when it gets dry, in short bursts with time to soak.

Board

Arduino Uno R3

Parts

Capacitive soil moisture sensor, water level sensor, push button, relay module, DC motor, +2 more

Level

Intermediate

Open in the simulator

### Bidirectional visitor counter

Two IR sensors at a doorway tell people coming in from going out, an I2C LCD shows IN, OUT and inside, and a relay lights the room while anyone is in.

Board

Arduino Uno R3

Parts

FC-51 IR obstacle sensor, relay module, DC jack and adapter, filament lamp, I2C LCD

Level

Intermediate

Open in the simulator

### Sump pump controller

A teaching model of a sump controller: two floats run a relay pump, an ACS712 checks that current really flows, and alarms catch a dead pump.

Board

Arduino Uno R3

Parts

Float switch, ACS712 current sensor, relay module, mini water pump, slide switch, +4 more

Level

Intermediate

Open in the simulator

### GFCI concept demo (not a real GFCI)

Two ACS712 sensors compare the hot and neutral current of a 12 V lamp and a relay latches open on a 60 mA imbalance: a teaching model.

Board

Arduino Uno R3

Parts

DC jack and adapter, ACS712 current sensor, relay module, filament lamp, resistor, +2 more

Level

Intermediate

Open in the simulator

### Fire fighting robot

Three flame sensors steer a 2WD car on an L298N to the fire, then a relay runs a water pump while a servo sweeps the nozzle until the flame is out.

Board

Arduino Uno R3

Parts

L298N motor driver, 2WD robot car chassis, flame sensor, servo motor, relay module, +1 more

Level

Advanced

Open in the simulator

### Keypad lock

A 4x4 keypad, a relay and an RGB LED on an Uno: type 1234 then # and the relay clicks the door lamp on.

Board

Arduino Uno R3

Parts

4x4 keypad, RGB LED, resistor, relay module, LED

Level

Advanced

Open in the simulator

### Motor starter

START and a fail-safe STOP, a relay and a small DC motor, and an ACS712 that feeds an inverse-time overload trip with a manual RESET.

Board

Arduino Uno R3

Parts

Push button, resistor, LED, limit switch, ACS712 current sensor, +4 more

Level

Advanced

Open in the simulator

### Bench supply monitor

An INA219 reads a 12 V supply’s volts, amps, watts and watt-hours on an LCD; an over-current knob trips a shutoff relay that latches, with a buzzer.

Board

Arduino Uno R3

Parts

INA219 current monitor, DC voltage source, relay module, resistor, slide switch, +5 more

Level

Advanced

Open in the simulator

### Pressure tank monitor

A pressure transducer and a pump relay run a 40/60 or 30/50 psi cut-in and cut-out, count pump cycles and run time, and flag short cycling.

Board

Arduino Uno R3

Parts

0.5 to 4.5 V pressure sender, relay module, filament lamp, slide switch, push button, +2 more

Level

Advanced

Open in the simulator

### Pick and place

Two steppers home to their switches, then each START moves a part from the pick point to the place point: nozzle down, vacuum on, up, across, down.

Board

Arduino Uno R3

Parts

Relay module, DC motor, servo motor, 28BYJ-48 stepper and ULN2003, limit switch, +2 more

Level

Advanced

Open in the simulator

### PLC ladder

A motor starter solved like a PLC: every scan reads all inputs into a table, solves the ladder rungs from it and writes the outputs at once.

Board

Arduino Uno R3

Parts

Traffic light module, relay module, DC motor, push button, limit switch, +2 more

Level

Advanced

Open in the simulator

### Delta-T monitor

Two DS18B20s on one wire read supply and return air: the drop across the coil is judged only while the cooling call runs and has settled.

Board

Arduino Uno R3

Parts

DS18B20 temperature sensor, float switch, relay module, slide switch, resistor, +1 more

Level

Advanced

Open in the simulator

Keep going

## Wiring, libraries and more ideas

The relay module part page Every project ideas list

### Wiring guides

- relay module to Arduino Uno
- relay module to ESP32
- relay module to Arduino Mega
- relay module to Arduino Nano
- relay module to Raspberry Pi Pico

### Library pages

- LiquidCrystal I2C library
- Servo library
- Adafruit BME280 library
- Adafruit INA219 library
- Adafruit Unified Sensor library
- Async TCP library

### More project ideas

- Arduino Uno project ideas
- ESP32 project ideas
- LED projects for Arduino, ESP32 and Pico
- Projects with a push button
- Projects with a slide switch
- Projects with an I2C LCD
- Projects with a lamp
- Projects with a water pump
- Projects with a DC motor
