Source: https://mokxi.com/ideas/raspberry-pi
Updated: 2026-11-17

Projects / Project ideas
Project ideas by board

# Raspberry Pi project ideas

12 Mokxi projects run on a Raspberry Pi computer (7 beginner and 5 intermediate). Here are all of them, from “Servo sweep with RPi.GPIO PWM” to “SSD1306 OLED on a Pi with smbus2”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

## How to pick your first one

- Start with “Servo sweep with RPi.GPIO PWM”, a beginner project that needs a servo motor.
- Most of them are beginner projects. Pick one a level below what you think you can do, finish it, then move up.
- The parts used most here are the LED (8 projects), the push button (2) and the BME280 weather sensor (1). With those on hand, most of this list is open to you.
- A Raspberry Pi runs Linux and Python, and its GPIO pins are 3.3 V only. Never wire 5 V straight to one.

Projects

## 12 projects ready to run

### Servo sweep with RPi.GPIO PWM

RPi.GPIO software PWM at 50 Hz on a Raspberry Pi 4: a servo on GPIO18 steps from 0 to 180 degrees and back, one position a second.

Board

Raspberry Pi 4 Model B

Parts

Servo motor

Level

Beginner

Open in the simulator

### Traffic lights with gpiozero

gpiozero TrafficLights and a Button on a Raspberry Pi 4: press the button and the lights go amber, red for crossing, red and amber, then green again.

Board

Raspberry Pi 4 Model B

Parts

Traffic light module, push button

Level

Beginner

Open in the simulator

### A button toggles an LED with gpiozero

gpiozero on a Raspberry Pi 4: each press of a button on GPIO2 turns the LED on GPIO17 on or off, with when_pressed and signal.pause().

Board

Raspberry Pi 4 Model B

Parts

Resistor, LED, push button

Level

Beginner

Open in the simulator

### Blink an LED with RPi.GPIO

RPi.GPIO on a Raspberry Pi Zero 2 W: an LED on GPIO17 blinks twice a second, and the Serial Monitor counts every four blinks.

Board

Raspberry Pi Zero 2 W

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### RPi.GPIO BCM and BOARD numbering

RPi.GPIO on a Raspberry Pi 4 with GPIO.setmode(GPIO.BOARD): two LEDs on header pins 11 and 13, which are GPIO17 and GPIO27 in BCM numbers.

Board

Raspberry Pi 4 Model B

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### PIR motion sensor with gpiozero

gpiozero MotionSensor on a Raspberry Pi 4: an HC-SR501 PIR on GPIO4 lights an LED on GPIO17 while something moves, and counts each movement.

Board

Raspberry Pi 4 Model B

Parts

Resistor, LED, PIR motion sensor

Level

Beginner

Open in the simulator

### Blink an LED with gpiozero

The first program on a Raspberry Pi 4: an LED on GPIO17 blinks once a second, in Python with gpiozero, and print() shows each change.

Board

Raspberry Pi 4 Model B

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### MQ-2 gas sensor on a Pi with an MCP3008

An MQ-2 on a Raspberry Pi 5: its 5 V output divided down to 3.3 V, read through an MCP3008 with gpiozero.

Board

Raspberry Pi 5

Parts

Eight-channel ADC, MQ-2 gas sensor, resistor, LED

Level

Intermediate

Open in the simulator

### BME280 on a Pi Zero 2 W with smbus2

A Raspberry Pi Zero 2 W reads a BME280 over I2C with smbus2 and the datasheet formulas: temperature, pressure and humidity every two seconds.

Board

Raspberry Pi Zero 2 W

Parts

BME280 weather sensor

Level

Intermediate

Open in the simulator

### Potentiometer through an MCP3008 on a Pi

gpiozero MCP3008 on a Raspberry Pi 5: a knob read through the ADC on SPI0 sets the brightness of an LED on GPIO18.

Board

Raspberry Pi 5

Parts

Eight-channel ADC, potentiometer, resistor, LED

Level

Intermediate

Open in the simulator

### HC-SR04 distance sensor with gpiozero

gpiozero DistanceSensor on a Raspberry Pi 5: an HC-SR04 with its echo divided down to 3.3 V.

Board

Raspberry Pi 5

Parts

HC-SR04 ultrasonic sensor, resistor, LED

Level

Intermediate

Open in the simulator

### SSD1306 OLED on a Pi with smbus2

A Raspberry Pi 4 draws text on an SSD1306 OLED over I2C bus 1 with smbus2: an uptime counter each second, and how long each frame takes at 100 kHz.

Board

Raspberry Pi 4 Model B

Parts

SSD1306 OLED display

Level

Intermediate

Open in the simulator

Keep going

## Wiring, libraries and more ideas

The Raspberry Pi 4 Model B board page Every project ideas list

### More project ideas

- Raspberry Pi Pico project ideas
- LED projects for Arduino, ESP32 and Pico
- Projects with a push button
- Projects with a BME280 sensor
- Projects with an ultrasonic sensor
- Projects with an MQ-2 gas sensor
- Projects with a PIR motion sensor
- Projects with a potentiometer
- Weather station projects
