Source: https://mokxi.com/ideas/pushbutton-projects
Updated: 2026-11-17

Projects / Project ideas
Project ideas by part

# Projects with a push button

187 Mokxi projects use a push button (64 beginner, 81 intermediate and 42 advanced). They run on Arduino Uno, ESP32 and Raspberry Pi Pico boards. Here are 24, from “LOLIN32 Lite button” to “ESP32-C3 Simon”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

## How to pick your first one

- Start with “CircuitPython button on a Pico”, a beginner project that needs a push button.
- Arduino Uno runs 140 of them, ESP32 19 and Raspberry Pi Pico 10. Start on the board you have, or on an Arduino Uno if you are buying one.
- The parts used most here are the LED (89 projects), the piezo speaker (52) and the potentiometer (29). With those on hand, most of this list is open to you.
- Before you build one on a real bench, read the push button wiring guide for your board below. It gives every pin and the voltage notes.

Projects

## 24 projects of 187

### LOLIN32 Lite button

A pushbutton on GPIO 4 lights the LOLIN32 Lite’s blue LED on GPIO 22, which comes on when its pin is LOW.

Board

Wemos LOLIN32 Lite

Parts

Push button

Level

Beginner

Open in the simulator

### Push button on pin 12 toggles the LED on pin 9

Each press of the button on pin 12 (10k pull-up) flips the LED on pin 9: on, then off.

Board

Arduino Uno R3

Parts

Push button, resistor, LED

Level

Beginner

Open in the simulator

### MicroPython table lamp on a Pico: a button toggles an LED

MicroPython on a Raspberry Pi Pico: each press of the button on GP13 turns the LED on GP15 on or off, with the contact bounce filtered out.

Board

Raspberry Pi Pico

Parts

Resistor, LED, push button

Level

Beginner

Open in the simulator

### Pico W button on GP14 with a pull-down

MicroPython on a Pico W: a push button from 3.3 V to GP14, held low by a 10k pull-down, prints a line to the Serial Monitor at each press.

Board

Raspberry Pi Pico W

Parts

Push button, resistor

Level

Beginner

Open in the simulator

### Traffic lights with gpiozero

gpiozero TrafficLights and a Button on a Raspberry Pi 4: press the button and the lights go amber, red for crossing, red and amber, then green again.

Board

Raspberry Pi 4 Model B

Parts

Traffic light module, push button

Level

Beginner

Open in the simulator

### Nucleo button

A pushbutton from PC13 to GND is the Nucleo’s USER button: pressing it lights the green LED on D13.

Board

STM32 Nucleo-F411RE

Parts

Push button

Level

Beginner

Open in the simulator

### D1 R32 button

A button on the Wemos D1 R32’s D2 hole, which is GPIO 26, lights an LED on D3, GPIO 25, and the blue LED on GPIO 2.

Board

Wemos D1 R32

Parts

Push button, resistor, LED

Level

Beginner

Open in the simulator

### micro:bit flashlight

A pushbutton on ring 1 of a micro:bit lights a lamp on ring 0 and a heart on the LED matrix while it is held.

Board

BBC micro:bit V2

Parts

Resistor, LED, push button

Level

Beginner

Open in the simulator

### Nano RP2040 button

A pushbutton on D2 of the Nano RP2040 Connect lights the LED on D13, with the RP2040’s own pull-up and the Nano’s pin names.

Board

Arduino Nano RP2040 Connect

Parts

Push button

Level

Beginner

Open in the simulator

### CircuitPython button on a Pico

CircuitPython on a Raspberry Pi Pico: a button on GP14 with the pin’s pull-up lights the board’s LED while it is held and counts each press.

Board

Raspberry Pi Pico

Parts

Push button

Level

Beginner

Open in the simulator

### A button toggles an LED with gpiozero

gpiozero on a Raspberry Pi 4: each press of a button on GPIO2 turns the LED on GPIO17 on or off, with when_pressed and signal.pause().

Board

Raspberry Pi 4 Model B

Parts

Resistor, LED, push button

Level

Beginner

Open in the simulator

### MicroPython button on GPIO 13 lights an LED

MicroPython on an ESP32: a push button on GPIO 13 with a 10k pull-up lights the LED on GPIO 2 for as long as it is held.

Board

ESP32-DevKitC V4

Parts

Resistor, LED, push button

Level

Beginner

Open in the simulator

### Digital piano

Eight keys and a piezo play an octave from middle C on an Uno.

Board

Arduino Uno R3

Parts

Push button, piezo speaker

Level

Beginner

Open in the simulator

### Garage door opener

A relay that presses the opener’s wall button for half a second and two reed switches that say closed, opening, open, closing or stopped.

Board

ESP32-C3-DevKitM-1

Parts

Reed switch, push button, relay module

Level

Intermediate

Open in the simulator

### Rangoli lights

A 16x16 WS2812B panel draws glowing rangoli patterns for Diwali, each symmetric eight ways from the center.

Board

Arduino Uno R3

Parts

Push button, resistor, WS2812 NeoPixel LEDs

Level

Intermediate

Open in the simulator

### GPS speedometer with a trip odometer

A NEO-6M and NeoGPS show speed, heading and satellites on an OLED, and a trip and total distance saved in EEPROM survive a reset.

Board

Arduino Uno R3

Parts

GPS module, push button, SSD1306 OLED display

Level

Intermediate

Open in the simulator

### ESP-NOW button and LED

Two ESP32s and no wire between them: the button on one sends on or off over ESP-NOW, the other lights its LED and prints each message.

Board

ESP32 DevKit V1

Parts

Push button, resistor, LED

Level

Intermediate

Open in the simulator

### Dice on an ESP32-C3

A button rolls a die and an ESP32-C3 tumbles the number onto a seven-segment display.

Board

ESP32-C3-DevKitM-1

Parts

Seven-segment display, resistor, push button

Level

Intermediate

Open in the simulator

### E-paper name badge

A 2.13 inch SSD1680 e-paper badge driven with GxEPD2: the name drawn once, a button that swaps the bottom line with a partial refresh.

Board

Arduino Uno R3

Parts

E-paper display, push button

Level

Intermediate

Open in the simulator

### Scoreboard

A MAX7219 eight-digit display driven with LedControl: home score, a ten-minute game clock and the guest score.

Board

Arduino Uno R3

Parts

Eight-digit display, push button

Level

Intermediate

Open in the simulator

### ESP32 Telegram doorbell with a PIR sensor

An ESP32 doorbell: the button rings a buzzer and sends you a Telegram message with UniversalTelegramBot, and a PIR sensor reports motion at the door.

Board

ESP32 DevKit V1

Parts

Push button, buzzer, PIR motion sensor

Level

Intermediate

Open in the simulator

### LED strip controller

Sixteen WS2812B pixels with on, off, brightness, color and two effects, faded between, from two buttons and a knob on the strip or from the Web tab.

Board

ESP32-C3-DevKitM-1

Parts

Potentiometer, push button, WS2812 NeoPixel LEDs

Level

Intermediate

Open in the simulator

### Pocket pet

A Tamagotchi-style pet on a 128x64 OLED: hatch it, feed it, play two mini-games, clean up, and it remembers you after a reset.

Board

Arduino Uno R3

Parts

SSD1306 OLED display, push button, piezo speaker

Level

Advanced

Open in the simulator

### ESP32-C3 Simon

Four LEDs flash a growing sequence, four buttons play it back.

Board

ESP32-C3-DevKitM-1

Parts

Resistor, LED, push button

Level

Advanced

Open in the simulator

Keep going

## Wiring, libraries and more ideas

The push button part page Every project ideas list

### Wiring guides

- push button to Arduino Uno
- push button to Raspberry Pi Pico
- push button to Arduino Nano
- push button to ESP32
- push button to Arduino Mega

### Library pages

- AceButton library
- Bounce2 library
- Button2 library
- ezButton library
- GyverButton library
- HotButton library

### More project ideas

- Arduino Uno project ideas
- ESP32 project ideas
- Raspberry Pi Pico project ideas
- Electronics projects with no code
- LED projects for Arduino, ESP32 and Pico
- Projects with a piezo speaker
- Projects with a potentiometer
- Projects with an I2C LCD
- Servo motor projects
- Projects with a buzzer
- Projects with a DC motor
