Source: https://mokxi.com/ideas/pro-micro
Updated: 2026-11-17

Projects / Project ideas
Project ideas by board

# Pro Micro and Leonardo project ideas

16 Mokxi projects run on a Pro Micro, Leonardo or Micro (3 beginner, 5 intermediate and 8 advanced). Here are all of them, from “Leonardo fade” to “Macro pad for streamers and coders”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

## How to pick your first one

- Start with “Leonardo fade”, a beginner project that needs a resistor and an LED.
- Most of them are advanced projects. Pick one a level below what you think you can do, finish it, then move up.
- The parts used most here are the LED (9 projects), the arcade button (6) and the KY-040 rotary encoder (5). With those on hand, most of this list is open to you.
- These boards have USB on the chip itself, which is why they can act as a keyboard, a mouse or a game controller.

Projects

## 16 projects ready to run

### Leonardo fade

Two LEDs off two different kinds of timer: the ten-bit one on pin 13 and an ordinary 16-bit one on pin 9.

Board

Arduino Leonardo

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### Micro blink

The Arduino Micro’s RX lamp, which lights when its pin goes low, blinking beside an LED on pin 9 that lights when it goes high.

Board

Arduino Micro

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### Pro Micro blink

A board with no LED on pin 13 blinks its RX lamp instead, with an LED on pin 9 beside it wired the ordinary way around.

Board

SparkFun Pro Micro

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### Leverless SOCD cleaning

Four direction buttons that can be held two at a time, cleaned by the neutral or last-input rule a slide switch picks.

Board

SparkFun Pro Micro

Parts

Game console buttons, slide switch, LED, resistor

Level

Intermediate

Open in the simulator

### Stream deck on a Pro Micro

Six keys with their labels drawn on an SSD1306 OLED, a second page on the sixth key, and a Ctrl+Shift+F-key hotkey for each press through Keyboard.h.

Board

SparkFun Pro Micro

Parts

SSD1306 OLED display, arcade button

Level

Intermediate

Open in the simulator

### Guitar controller on a Pro Micro

Five fret buttons, a two-switch strum bar, a whammy knob and a tilt switch for star power, sent as a gamepad report through Joystick.h.

Board

SparkFun Pro Micro

Parts

Limit switch, push button, arcade button, potentiometer, tilt switch

Level

Intermediate

Open in the simulator

### Dance pad on a Pro Micro

Four FSR panels on A0 to A3 with a press and a release threshold each, lighting a panel lamp and sent as four gamepad buttons through Joystick.h.

Board

SparkFun Pro Micro

Parts

Force-sensing resistor, LED, resistor

Level

Intermediate

Open in the simulator

### Fight stick on a Pro Micro

A four-way lever and six buttons on a Pro Micro, debounced with no added delay and reported as a numpad direction plus the buttons held.

Board

SparkFun Pro Micro

Parts

Game console buttons, arcade button

Level

Intermediate

Open in the simulator

### Sim racing button box

Two encoders, an ignition key with a start button, three toggles, four buttons and three LEDs on a Pro Micro, sent to the game as one USB controller.

Board

SparkFun Pro Micro

Parts

Slide switch, arcade button, KY-040 rotary encoder, LED, resistor

Level

Advanced

Open in the simulator

### Load cell pedals on a Pro Micro

A load cell brake on an HX711 that responds to force, a hall sensor throttle and a pot clutch, each calibrated and sent as one Joystick.h report.

Board

SparkFun Pro Micro

Parts

Load cell with HX711, 49E linear hall sensor, potentiometer

Level

Advanced

Open in the simulator

### Key matrix numpad

Twelve switches in a 4 x 3 matrix with a diode on every key, three layers, an encoder and per-key RGB on a Pro Micro, typed as a USB keyboard.

Board

SparkFun Pro Micro

Parts

Push button, diode, KY-040 rotary encoder, WS2812 NeoPixel LEDs

Level

Advanced

Open in the simulator

### Flight stick and throttle on a Pro Micro

A two-axis stick with a center deadzone and an expo curve, a twist rudder, a hall sensor throttle, a hat switch and two buttons.

Board

SparkFun Pro Micro

Parts

Game console buttons, 49E linear hall sensor, potentiometer, joystick

Level

Advanced

Open in the simulator

### MIDI controller

Two faders, a knob, four drum pads and an encoder on a Pro Micro, sending real MIDI bytes the 5-pin way.

Board

SparkFun Pro Micro

Parts

Resistor, LED, slide potentiometer, push button, potentiometer, +1 more

Level

Advanced

Open in the simulator

### H-pattern shifter and handbrake

Two pots read an H-pattern gate with hysteresis and push-down reverse, two microswitches make sequential paddles and a hall sensor is the handbrake.

Board

SparkFun Pro Micro

Parts

TM1637 four-digit display, limit switch, slide potentiometer, arcade button, 49E linear hall sensor

Level

Advanced

Open in the simulator

### Autopilot and landing gear panel

An autopilot knob for heading, altitude and vertical speed on a four-digit display, an AP button.

Board

SparkFun Pro Micro

Parts

TM1637 four-digit display, KY-040 rotary encoder, slide switch, arcade button, LED, +1 more

Level

Advanced

Open in the simulator

### Macro pad for streamers and coders

A Pro Micro that plugs in as a keyboard: twelve keys of shortcuts, a volume knob, three layers with a lamp each and an OLED.

Board

SparkFun Pro Micro

Parts

4x3 telephone keypad, KY-040 rotary encoder, SSD1306 OLED display, LED, resistor

Level

Advanced

Open in the simulator

Keep going

## Wiring, libraries and more ideas

The SparkFun Pro Micro board page Every project ideas list

### Library pages

- Arduino Joystick library
- Adafruit GFX library
- Adafruit SSD1306 library
- Encoder library
- TM1637 library
- Adafruit NeoPixel library

### More project ideas

- LED projects for Arduino, ESP32 and Pico
- Projects with an arcade button
- Projects with a rotary encoder
- Projects with a potentiometer
- Projects with game console buttons
- Projects with a push button
- Projects with a slide switch
- Projects with a hall effect sensor
- Arduino game projects
- Arduino music and sound projects
