Source: https://mokxi.com/ideas/mfrc522-projects
Updated: 2026-11-17

Projects / Project ideas
Project ideas by part

# Projects with an RFID reader

11 Mokxi projects use an MFRC522 RFID reader (1 beginner, 3 intermediate and 7 advanced). They run on Arduino Uno, Raspberry Pi Pico and Arduino Mega boards. Here are all of them, from “RC522 RFID reader (SS 10, RST 9)” to “RFID time clock with an LCD and a DS1307”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

## How to pick your first one

- Start with “RC522 RFID reader (SS 10, RST 9)”, a beginner project that needs an RFID reader.
- Arduino Uno runs 6 of them, Raspberry Pi Pico 3 and Arduino Mega 1. Start on the board you have, or on an Arduino Uno if you are buying one.
- The parts used most here are the piezo speaker (4 projects), the I2C LCD (3) and the LED (3). With those on hand, most of this list is open to you.
- Before you build one on a real bench, read the MFRC522 RFID reader wiring guide for your board below. It gives every pin and the voltage notes.

Projects

## 11 projects ready to run

### RC522 RFID reader (SS 10, RST 9)

An RC522 RFID reader on the SPI pins with SDA (SS) on pin 10 and RST on pin 9: hold a card to it and the MFRC522 library prints the card’s ID.

Board

Arduino Uno R3

Parts

MFRC522 RFID reader

Level

Beginner

Open in the simulator

### RFID reader with an I2C LCD

An RC522 reader on the SPI pins with SS on 10 and RST on 9 reads a card’s UID and shows it on an I2C LCD on A4 and A5.

Board

Arduino Uno R3

Parts

MFRC522 RFID reader, I2C LCD

Level

Intermediate

Open in the simulator

### ESP32 traffic emergency system with RFID

Three roads’ lights take turns on an ESP32. Click the white card beside a road’s MFRC522 reader: that road gets green for 8 s and the others red.

Board

ESP32 DevKit V1

Parts

MFRC522 RFID reader, resistor, LED

Level

Intermediate

Open in the simulator

### RFID door

An MFRC522 reader and four cards. Tap one: two are on the list and light the green lamp, the other two light the red.

Board

Arduino Uno R3

Parts

MFRC522 RFID reader, resistor, LED

Level

Intermediate

Open in the simulator

### Access control: RFID card opens a stepper door

An RC522 reader (SS 10, RST 9) checks each card against the one it knows.

Board

Arduino Uno R3

Parts

MFRC522 RFID reader, 28BYJ-48 stepper and ULN2003, I2C LCD

Level

Advanced

Open in the simulator

### MicroPython RFID on a Pico: read a card’s UID, RC522

MicroPython on a Raspberry Pi Pico: an RC522 reader on SoftSPI (GP2 to GP5) prints a MIFARE card’s UID and reads block 8 with the factory key.

Board

Raspberry Pi Pico

Parts

MFRC522 RFID reader

Level

Advanced

Open in the simulator

### Pico W MFRC522 reads and writes RFID cards

MicroPython on a Pico W: an MFRC522 on SPI0 reads a card’s UID and the text stored on it, and writes text typed in the Serial Monitor to a card.

Board

Raspberry Pi Pico W

Parts

MFRC522 RFID reader

Level

Advanced

Open in the simulator

### Escape-room puzzle box

Five puzzles in ten minutes: a keypad code, a magnet key, the right RFID card, a tilt sequence and three flashes of light.

Board

Arduino Mega 2560 R3

Parts

4x4 keypad, reed switch, piezo speaker, MPU6050 accelerometer and gyro, servo motor, +6 more

Level

Advanced

Open in the simulator

### Pico W RFID music player with a WS2812 strip

MicroPython on a Pico W: lay an RFID card on an MFRC522 and the notes stored on it play on a passive buzzer while a WS2812 strip flashes a color per.

Board

Raspberry Pi Pico W

Parts

MFRC522 RFID reader, WS2812 NeoPixel LEDs, piezo speaker, transistor, resistor

Level

Advanced

Open in the simulator

### RFID attendance system

RFID attendance system on an Arduino: tap a card on an RC522, the LCD shows IN, LATE or OUT with the DS3231 time, and a CSV on the SD card logs it.

Board

Arduino Uno R3

Parts

MFRC522 RFID reader, microSD card module, DS3231 real-time clock, I2C LCD, piezo speaker

Level

Advanced

Open in the simulator

### RFID time clock with an LCD and a DS1307

Swipe a card on an RC522 (SS 10, RST A1) to clock in: the LCD names the person, a DS1307 stamps the time, and a line goes to the serial monitor.

Board

Arduino Uno R3

Parts

16x2 character LCD, MFRC522 RFID reader, DS1307 real-time clock, push button, piezo speaker

Level

Advanced

Open in the simulator

Keep going

## Wiring, libraries and more ideas

The MFRC522 RFID reader part page Every project ideas list

### Wiring guides

- RC522 RFID reader to Arduino Uno
- RC522 RFID reader to Arduino Mega
- RC522 RFID reader to ESP32
- RC522 RFID reader to Raspberry Pi Pico
- RC522 RFID reader to Arduino Nano

### Library pages

- MFRC522 library
- SPI library
- LiquidCrystal I2C library
- RTClib library
- Keypad library
- LiquidCrystal library

### More project ideas

- Arduino Uno project ideas
- Raspberry Pi Pico project ideas
- Arduino Mega project ideas
- ESP32 project ideas
- Projects with a piezo speaker
- Projects with an I2C LCD
- LED projects for Arduino, ESP32 and Pico
- Projects with a push button
- Projects with a DS1307 real-time clock
- Projects with a DS3231 real-time clock
- Projects with a 4x4 keypad
