Source: https://mokxi.com/ideas/led-projects
Updated: 2026-11-17

Projects / Project ideas
Project ideas by part

# LED projects for Arduino, ESP32 and Pico

278 Mokxi projects use an LED (141 beginner, 100 intermediate and 37 advanced). They run on Arduino Uno and ESP32 boards, and 32 need no board at all. Here are 24, from “Relay module on pin 8” to “An ESP32 and an Arduino Uno talking over serial”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

## How to pick your first one

- Start with “Blink, with a breakpoint”, a beginner project that needs a resistor and an LED.
- Arduino Uno runs 142 of them, ESP32 43 and 32 need no board at all. Start on the board you have, or on an Arduino Uno if you are buying one.
- The parts used most here are the push button (89 projects), the potentiometer (38) and the piezo speaker (31). With those on hand, most of this list is open to you.
- Before you build one on a real bench, read the LED wiring guide for your board below. It gives every pin and the voltage notes.

Projects

## 24 projects of 278

### Relay module on pin 8

A relay module on pin 8 clicks on and off every two seconds; its contact switches an LED.

Board

Arduino Uno R3

Parts

Resistor, LED, relay module

Level

Beginner

Open in the simulator

### ESP32-C3 PWM fade

Breathes an LED on GPIO 4 and the on-board one on GPIO 8 with analogWrite.

Board

ESP32-C3-DevKitM-1

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### Pico W chaser

Six lamps sweeping on the breadboard, on the same pins as the Pico’s chaser.

Board

Raspberry Pi Pico W

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### STM32 chaser

A six-LED sweep that runs back and forth on the Black Pill, wired to PA1 through PA6.

Board

STM32F411 Black Pill

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### ESP-01 blink

An LED wired from 3V3 through a resistor to GPIO 2 lights together with the module’s own blue one, whenever the pin goes low.

Board

ESP-01S

Parts

LED, resistor

Level

Beginner

Open in the simulator

### NodeMCU fade

An LED breathing on an ESP8266, which has no PWM hardware at all: the core moves the pin itself, and the range is 0 to 1023.

Board

ESP8266 NodeMCU V1.0

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### MicroPython motion sensor on a Pico: PIR on GP18, LED

MicroPython on a Raspberry Pi Pico: an HC-SR501 motion sensor on GP18 lights the LED on GP15 for as long as its output says something moved.

Board

Raspberry Pi Pico

Parts

PIR motion sensor, resistor, LED

Level

Beginner

Open in the simulator

### ESP32 web server with two LEDs

The Random Nerd Tutorials ESP32 web server: press Run, open the Web panel, and its ON and OFF buttons switch the LEDs on GPIO 26 and 27.

Board

ESP32 DevKit V1

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### Uno R4 knob

A potentiometer on an Uno R4’s A0 fades an LED on pin 9, and the monitor prints the same pin in ten bits and in the converter’s own fourteen.

Board

Arduino Uno R4 Minima

Parts

Potentiometer, resistor, LED

Level

Beginner

Open in the simulator

### Nucleo blink

The STM32 Nucleo-F411RE’s green LED on D13 and an LED beside the board, which light when the pin is HIGH, as on an Uno.

Board

STM32 Nucleo-F411RE

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### Leonardo fade

Two LEDs off two different kinds of timer: the ten-bit one on pin 13 and an ordinary 16-bit one on pin 9.

Board

Arduino Leonardo

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### Dimmer

A potentiometer on A0 sets the brightness of an LED on pin 9. Turn the knob while it runs.

Board

Arduino Uno R3

Parts

Potentiometer, resistor, LED

Level

Beginner

Open in the simulator

### RP2040-Zero blink

An LED on GP0 of the RP2040-Zero, which has no plain LED of its own, with the board beside the breadboard.

Board

Waveshare RP2040-Zero

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### XIAO S3 knob

The XIAO knob circuit on the ESP32-S3: D0 is A0 on GPIO 1, and the count is printed as the converter gives it.

Board

Seeed XIAO ESP32-S3

Parts

Potentiometer, resistor, LED

Level

Beginner

Open in the simulator

### SuperMini blink

The blue LED on GPIO 8 lights when the pin is low and an LED on GPIO 2 when it is high, on the smallest ESP32-C3 board.

Board

ESP32-C3 SuperMini

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### A button toggles an LED with gpiozero

gpiozero on a Raspberry Pi 4: each press of a button on GPIO2 turns the LED on GPIO17 on or off, with when_pressed and signal.pause().

Board

Raspberry Pi 4 Model B

Parts

Resistor, LED, push button

Level

Beginner

Open in the simulator

### Blue Pill lamp

A lamp on a Blue Pill that blinks in step with the board’s own LED, because both hang off 3.3 V and PC13 sinks them.

Board

STM32 Blue Pill (F103)

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### ATmega328P at 8 MHz

An ATmega328P in a breadboard on its internal 8 MHz clock, with no crystal, running a blink built for 8 MHz.

Board

ATmega328P, 8 MHz internal clock

Parts

ATmega328P, resistor, LED

Level

Beginner

Open in the simulator

### Night light with a light sensor

A light-dependent resistor in a divider fades a lamp up when the room goes dark. Drag the slider on the sensor.

Board

Arduino Uno R3

Parts

Photoresistor, resistor, LED

Level

Beginner

Open in the simulator

### Nano dial

A potentiometer on the Nano's A7, the analog-only pin an Uno does not have, fades an LED on pin 9.

Board

Arduino Nano

Parts

Potentiometer, resistor, LED

Level

Beginner

Open in the simulator

### Blink, with a breakpoint

Stop the board on the line that lights the LED, and see it frozen mid-blink with its registers.

Board

ESP32-C3-DevKitM-1

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### Dance pad on a Pro Micro

Four FSR panels on A0 to A3 with a press and a release threshold each, lighting a panel lamp and sent as four gamepad buttons through Joystick.h.

Board

SparkFun Pro Micro

Parts

Force-sensing resistor, LED, resistor

Level

Intermediate

Open in the simulator

### HC-SR04 distance sensor with gpiozero

gpiozero DistanceSensor on a Raspberry Pi 5: an HC-SR04 with its echo divided down to 3.3 V.

Board

Raspberry Pi 5

Parts

HC-SR04 ultrasonic sensor, resistor, LED

Level

Intermediate

Open in the simulator

### An ESP32 and an Arduino Uno talking over serial

An ESP32 reads a knob and sends the number to an Arduino Uno over a serial wire; the Uno sets an LED’s brightness from it.

Board

ESP32 DevKit V1 and Arduino Uno R3

Parts

Potentiometer, resistor, LED

Level

Intermediate

Open in the simulator

Keep going

## Wiring, libraries and more ideas

The LED part page Every project ideas list

### Wiring guides

- LED to Arduino Uno
- LED to Raspberry Pi Pico
- LED to Arduino Nano
- LED to Arduino Mega

### Library pages

- Chrono library
- CountDown library
- Tasker library
- Servo library
- LiquidCrystal I2C library
- Keypad library

### More project ideas

- Arduino Uno project ideas
- ESP32 project ideas
- Electronics projects with no code
- Raspberry Pi Pico project ideas
- Projects with a push button
- Projects with a potentiometer
- Projects with a piezo speaker
- Projects with a slide switch
- Projects with a buzzer
- Projects with a transistor
- Servo motor projects
