Source: https://mokxi.com/ideas/lcd2004i2c-projects
Updated: 2026-11-17

Projects / Project ideas
Project ideas by part

# Projects with a 20x4 I2C LCD

7 Mokxi projects use a 20x4 I2C LCD (5 intermediate and 2 advanced). They run on Arduino Uno and Arduino Mega boards. Here are all of them, from “Twenty by four” to “Escape-room puzzle box”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

## How to pick your first one

- Start with “Twenty by four”, an intermediate project that needs a character LCD.
- Arduino Uno runs 5 of them and Arduino Mega 2. Start on the board you have, or on an Arduino Uno if you are buying one.
- The parts used most here are the push button (4 projects), the buzzer (2) and the LED (2). With those on hand, most of this list is open to you.
- Before you build one on a real bench, open the 20x4 I2C LCD part page for its pins and what each one does.

Projects

## 7 projects ready to run

### Twenty by four

Two 20x4 character LCDs, one on six wires and one on its I2C backpack. A long line runs off row 0 and carries on in row 2.

Board

Arduino Uno R3

Parts

Character LCD

Level

Intermediate

Open in the simulator

### Solar battery monitor with an INA3221

One INA3221 reads a solar panel, an 18650 and its load on three channels, and a 20x4 LCD shows volts, currents and whether the cell is charging.

Board

Arduino Uno R3

Parts

Three-channel current monitor, solar panel, li-ion charger, battery: AA, filament lamp, +1 more

Level

Intermediate

Open in the simulator

### Tire pressure check station

An MPX5700 gauge pressure sensor on a shop air chuck, auto-zeroed at power up: the tire in psi, kPa and bar on a 20x4 LCD.

Board

Arduino Uno R3

Parts

Traffic light module, pressure sensor, push button, buzzer, 20x4 I2C LCD

Level

Intermediate

Open in the simulator

### Boost and oil pressure gauge

Oil pressure from a 0.5 to 4.5 V sender and boost or vacuum from an absolute MAP sensor on a 20x4 LCD, with a resettable peak boost.

Board

Arduino Uno R3

Parts

0.5 to 4.5 V pressure sender, pressure sensor, resistor, push button, buzzer, +2 more

Level

Intermediate

Open in the simulator

### Line OEE dashboard

A 20x4 LCD shows how well a machine is doing as one number: availability, performance and quality from a part counter.

Board

Arduino Uno R3

Parts

Slide switch, push button, E18-D80NK IR proximity switch, potentiometer, 20x4 I2C LCD

Level

Intermediate

Open in the simulator

### Spaceship control panel

Arm three systems, pass the go/no-go poll, lift the safety and launch.

Board

Arduino Mega 2560 R3

Parts

Slide switch, LED arcade button, TM1637 four-digit display, piezo speaker, WS2812 NeoPixel LEDs, +7 more

Level

Advanced

Open in the simulator

### Escape-room puzzle box

Five puzzles in ten minutes: a keypad code, a magnet key, the right RFID card, a tilt sequence and three flashes of light.

Board

Arduino Mega 2560 R3

Parts

4x4 keypad, reed switch, piezo speaker, MPU6050 accelerometer and gyro, servo motor, +6 more

Level

Advanced

Open in the simulator

Keep going

## Wiring, libraries and more ideas

The 20x4 I2C LCD part page Every project ideas list

### Library pages

- LiquidCrystal I2C library
- hd44780 library
- Servo library
- Adafruit NeoPixel library
- Keypad library
- LiquidCrystal library

### More project ideas

- Arduino Uno project ideas
- Arduino Mega project ideas
- Projects with a push button
- Projects with a buzzer
- LED projects for Arduino, ESP32 and Pico
- Projects with a piezo speaker
- Servo motor projects
- Projects with a slide switch
