Source: https://mokxi.com/ideas/lcd1602i2c-projects
Updated: 2026-11-17

Projects / Project ideas
Project ideas by part

# Projects with an I2C LCD

85 Mokxi projects use an I2C LCD (23 beginner, 44 intermediate and 18 advanced). They run on Arduino Uno, Raspberry Pi Pico and ESP32 boards. Here are 24, from “Water pressure gauge” to “Smart home hub”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

## How to pick your first one

- Start with “Water pressure gauge”, a beginner project that needs a pressure transducer and an I2C LCD.
- Arduino Uno runs 74 of them, Raspberry Pi Pico 5 and ESP32 4. Start on the board you have, or on an Arduino Uno if you are buying one.
- The parts used most here are the push button (28 projects), the buzzer (15) and the piezo speaker (15). With those on hand, most of this list is open to you.
- Before you build one on a real bench, read the I2C LCD wiring guide for your board below. It gives every pin and the voltage notes.

Projects

## 24 projects of 85

### Water pressure gauge

A 0.5 to 4.5 V stainless pressure transducer on a water line and a 16x2 I2C LCD: the pressure in psi and bar, with a warning when it drops.

Board

Arduino Uno R3

Parts

0.5 to 4.5 V pressure sender, I2C LCD

Level

Beginner

Open in the simulator

### Stopwatch with lap times

Stopwatch with lap times on an Arduino Nano and a 16x2 LCD: one button starts, stops and carries on, the other takes laps or resets.

Board

Arduino Nano

Parts

Arcade button, piezo speaker, I2C LCD

Level

Beginner

Open in the simulator

### Electronic voting machine

Electronic voting machine on an Arduino Nano: four buttons to vote, a result button for every count and the winner on an LCD.

Board

Arduino Nano

Parts

Arcade button, piezo speaker, I2C LCD

Level

Beginner

Open in the simulator

### Object counter with an E18-D80NK

An E18-D80NK infrared sensor on pin 2 with the pin’s pull-up: each object that passes adds one to the count on a 16x2 I2C LCD, with a beep.

Board

Arduino Uno R3

Parts

E18-D80NK IR proximity switch, buzzer, I2C LCD

Level

Beginner

Open in the simulator

### Fever thermometer

An MLX90614 reads a forehead without touching it; an I2C LCD shows the temperature, and over 38 C it says FEVER and beeps.

Board

Arduino Uno R3

Parts

IR thermometer, I2C LCD, piezo speaker

Level

Beginner

Open in the simulator

### I2C LCD clock and thermometer

An I2C LCD on A4 and A5 shows the time, kept by a timer interrupt every second, and the temperature from a thermistor on A0.

Board

Arduino Uno R3

Parts

10k NTC thermistor, resistor, I2C LCD

Level

Intermediate

Open in the simulator

### MicroPython DHT11 and LCD1602 on a Pico

MicroPython on a Raspberry Pi Pico: a DHT11 on GP5 and an I2C LCD1602 on GP14 and GP15 show the temperature and humidity, refreshed every two seconds.

Board

Raspberry Pi Pico

Parts

DHT11 or DHT22 sensor, resistor, I2C LCD

Level

Intermediate

Open in the simulator

### Thermometer on an I2C LCD

A 10 k NTC bead in a divider on A0, the temperature on a 16x2 character LCD over its PCF8574 backpack. Four wires to the display.

Board

Arduino Uno R3

Parts

10k NTC thermistor, resistor, I2C LCD

Level

Intermediate

Open in the simulator

### Pitot airspeed meter

An MPX5010DP differential pressure sensor on a pitot tube and a 16x2 I2C LCD: the wind’s pressure in pascals and the airspeed it means.

Board

Arduino Uno R3

Parts

Pressure sensor, I2C LCD

Level

Intermediate

Open in the simulator

### Pico W WiFi weather and time on an I2C LCD

MicroPython on a Pico W: join the simulated WiFi, fetch the weather and the time with urequests, and show both on an I2C LCD1602 on GP6 and GP7.

Board

Raspberry Pi Pico W

Parts

I2C LCD

Level

Intermediate

Open in the simulator

### MicroPython DHT readings on an I2C LCD

MicroPython on an ESP32: a DHT22 on GPIO 18 shows temperature and humidity on an I2C LCD1602 (SDA 13, SCL 14), every two seconds.

Board

ESP32-DevKitC V4

Parts

DHT11 or DHT22 sensor, resistor, I2C LCD

Level

Intermediate

Open in the simulator

### Breathalyzer with an MQ-3

An MQ-3 alcohol sensor calibrated in clean air with MQUnifiedsensor.

Board

Arduino Uno R3

Parts

Traffic light module, alcohol sensor, I2C LCD

Level

Intermediate

Open in the simulator

### Guess the number: IR remote and an I2C LCD

The board picks a number from 0 to 99; type guesses on the remote (IR receiver on pin 2), press PLAY/PAUSE to check.

Board

Arduino Uno R3

Parts

IR receiver and remote, IR remote, I2C LCD

Level

Intermediate

Open in the simulator

### RFID reader with an I2C LCD

An RC522 reader on the SPI pins with SS on 10 and RST on 9 reads a card’s UID and shows it on an I2C LCD on A4 and A5.

Board

Arduino Uno R3

Parts

MFRC522 RFID reader, I2C LCD

Level

Intermediate

Open in the simulator

### Touch climate display

An AHT20 and a 16x2 I2C LCD on the same two wires, and a TTP223 touch pad that flips the reading between Celsius and Fahrenheit.

Board

Arduino Uno R3

Parts

Humidity sensor, I2C LCD, touch sensor

Level

Intermediate

Open in the simulator

### MicroPython I2C LCD1602: hello and a counter

MicroPython on an ESP32: an LCD1602 on an I2C backpack, SDA on GPIO 13 and SCL on 14, says hello and counts the seconds.

Board

ESP32-DevKitC V4

Parts

I2C LCD

Level

Intermediate

Open in the simulator

### Pico W room temperature on an I2C LCD

MicroPython on a Pico W: a 10k thermistor divider on GP28 gives the temperature, and an I2C LCD1602 on GP6 and GP7 shows it every second.

Board

Raspberry Pi Pico W

Parts

I2C LCD, resistor, 10k NTC thermistor

Level

Intermediate

Open in the simulator

### Wind and rain station

The SparkFun weather meter kit on an Uno: wind speed from the anemometer, direction from the vane and rain from the bucket, on an I2C LCD.

Board

Arduino Uno R3

Parts

Weather meter kit, resistor, I2C LCD

Level

Intermediate

Open in the simulator

### Pico W guess the number: keypad and LCD

MicroPython on a Pico W: a number game on a 4x4 keypad (rows GP21 to GP18.

Board

Raspberry Pi Pico W

Parts

I2C LCD, 4x4 keypad

Level

Advanced

Open in the simulator

### Access control: RFID card opens a stepper door

An RC522 reader (SS 10, RST 9) checks each card against the one it knows.

Board

Arduino Uno R3

Parts

MFRC522 RFID reader, 28BYJ-48 stepper and ULN2003, I2C LCD

Level

Advanced

Open in the simulator

### Typewriter

A PS/2 keyboard read on an interrupt and printed on a 16x2 LCD: type on it for real and watch the scan codes become letters.

Board

ESP32-C3-DevKitM-1

Parts

PS/2 keyboard, I2C LCD

Level

Advanced

Open in the simulator

### nRF24L01 sensor network with RF24Network

Two nRF24L01 sensor nodes send DS18B20 temperatures to a base node every 2 seconds, and the base shows each one on an LCD.

Board

Arduino Uno R3

Parts

NRF24L01+ 2.4 GHz radio, I2C LCD, DS18B20 temperature sensor

Level

Advanced

Open in the simulator

### LoRa weather station with acknowledgments

A BME280 node sends temperature, humidity and pressure over LoRa with RadioHead, and a gateway acknowledges each reading and shows it on an I2C LCD.

Board

Arduino Uno R3

Parts

LoRa module, BME280 weather sensor, I2C LCD

Level

Advanced

Open in the simulator

### Smart home hub

An ESP32-C3 web dashboard that switches a lamp and a fan through relays, dims a porch light, reads temperature, humidity and motion.

Board

ESP32-C3-DevKitM-1

Parts

Two-channel relay board, filament lamp, DC motor, LED, resistor, +4 more

Level

Advanced

Open in the simulator

Keep going

## Wiring, libraries and more ideas

The I2C LCD part page Every project ideas list

### Wiring guides

- I2C LCD to Arduino Uno
- I2C LCD to Arduino Nano
- I2C LCD to Raspberry Pi Pico
- I2C LCD to Arduino Mega
- I2C LCD to ESP32

### Library pages

- LiquidCrystal I2C library
- hd44780 library
- LCD_I2C library
- LiquidCrystal_PCF8574 library
- Wire library
- Servo library

### More project ideas

- Arduino Uno project ideas
- Raspberry Pi Pico project ideas
- ESP32 project ideas
- Arduino Nano project ideas
- Projects with a push button
- Projects with a buzzer
- Projects with a piezo speaker
- Projects with a DC motor
- LED projects for Arduino, ESP32 and Pico
- Servo motor projects
- Projects with a limit switch
